Having problems with your Maytag 24 in. MDBH950AWS Built-in Dishwasher ?

Maytag MDBH955aws When you push the cycle

\015 Maytag MDBH955aws When you push the cycle buttons, only the heavy wash lite comes on. All the option lites come and the auto wash lite as well. When you push the start button, nothing happens. The drain and supply lines are clear and not pinched. The power cable is connected, properly grounded, and it is connected to it's own breaker.\015\012The washer was working fine the last time it was used, then completely\015\012failed the next time we wanted to use it. It can't be more then 3 years old. I'm at a loss, but am guessing it is probably in to electronic control\015\012panel.\015

Answers :


If you see the lights and button works, but No response from machine - You might have a Faulty Pump Motor. If you do not see any lights, then you can guess at Control Board/User Interface.

Then , you might try to Reset the breaker.

Let me know, if you need further assistance.

Hope i helped you.

Thanks for using ' Fixya ' and have a nice day!!
Hello. Since you have checked the power the next most common reason for the problem as stated is \015\012\015\012\015\012\015\012\015\012Lid switch\015\012\015\012If the lid switch is defective, your washer can't spin and may not function at all. The switch is inside the washing machine main housing near the door frame. Often you have to raise or open the top or front of the washer to get to the switch. If it's defective, you need to replace it.

Some machines have a special lid-switch fuse near the lid switch, inside the control panel. If this fuse blows, the unit won't fill with water until you replace the fuse.
Repair Help & Product Troubleshooting for Maytag 24 in. MDBH950AWS Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Maytag Quiet Series 300 Dishwasher will not stop flashing [81] if I push any normal cycle, or the [2h] if I push the delay button.The washer never cycles though. Is there an reset option or what shou

... Dishwashers

Maytag dishwasher mdb7601 will not run- light doesn't come on and nothing happens when you push the buttons. Earlier it would work but if you pushed the light cycle button the longer cycle would light up and it would run. Then the time running light did not light up.

... Maytag MDB7100AWB Dishwasher

I have a Maytag Quiet Series 300 dishwasher model number MDBH955AWW. When I press the wash cycle button it starts and then automatically jumps to the rinse cycle. After going thru the rinse cycle for a couple of minutes, it shuts off. After that,I can push the wash cycle agin and it works. Any idea what could be wrong?

HI. This will be a basic logic chip fault. It could possibly be solved by simply preforming a hard reset. You can do this by shutting down the power to the unit for five minutes. This shutdown will force the logic sector of your electronic control bo ... Maytag 24 in. MDB9750AW Dishwasher

Maytag MDBH985AWS...control panel button to turn on the washer does not work...wash cycle and delay lights will light when pushed but washer will not come on. Have tried pushing normal wash and heated dry in sequence, flipped circuit breaker, open and close door, pushed buttons while door is closed

... Maytag MDBH985AWB / MDBH985AWS 24 in. Built-in Dishwasher

Maytag MDBH955aws When you push the cycle

Hi,If you see the lights and button works, but No response from machine - You might have a Faulty Pump Motor. If you do not see any lights, then you can guess at Control Board/User Interface.Then , you might try to Reset the ... Maytag 24 in. MDBH950AWS Built-in Dishwasher

Have a brand new maytag dishwasher. When the cycle is finished the clean light stays on and I have to push buttons to clear is this normal?

If you open the door after the cycle, does it clear the display? Mine is a different maytag model, and when it's done it shows the display as clean. The display will go blank when I open the door manually... let me know if that helps.KEN ... Maytag 24 in. MDB5651A Built-in Dishwasher

I have a maytag dishwasher model MDB7749AWB1 that suddenly won't start; i push the cycle that i want and push start and the light comes on like its going to start but then in about one second it starts blinking and the dishwasher never starts.

... Maytag Dishwashers

Maytag mdb6601aww push normal wash button-- nothing happens. push other wash cycles, the lights flash about 30 times then stop-- then nothing happens. tried clearing codes. hi temp wash then heated dry , hi temp wash then heated dry. same problem. also tried normal wash then heated dry 3 times in 6 seconds--- same thing. also tried unplugging unit waiting 10 minutes with no luck. thanks

... Maytag 24 in. MDB6100A Built-in Dishwasher

Our maytag mdbh979awb has 3 lights flashing normal, start resume, and cancel it stopped mid-cycle. We have cut power for an hour. Pushed start/resume once, and cancle twice.. we have pushed each button to check for a stuck button.. Help:(

... Maytag Dishwashers

Our dishwasher (a Maytag - MDBH970AW) will not proceed past the intital intake of water. It has done this occasionally in the past, but with repeated attempts to start a wash cycle, it would eventually work and continue to work for some time afterward. However, in the past week, it will not go through a wash cycle. I have ran the water, prior to starting, to ensure that it is intaking very hot water. When it quits, I can push the start button again and it will go through the 2 minute drain c

... Maytag 24 in. MDBH970AW Built-in Dishwasher

My Maytag dishwasher MDB6759AWS3 just stopped working. I had to stop it mid cycle and then I pushed cancel drain and now some of the buttons light up but not the start button

... Maytag 24 in. MDBH950AWS Built-in Dishwasher

Maytag dw mdb7809awb1 wash cycle and rinse lights work but will not start when I push start button. Where do i begin to check for problem? Thanks

... Maytag MDB7609AWS Builtin Dishwasher

Just bought a 4 year old maytag 300 quiet series and hooked it up all front buttons light up when you push what you want but will not fill with water. Goes to cycle where water should be spraying around but will not fill with any water.

Sounds like an internal timer malfunction.\012\012Maytag Customer Service: 1 (800) 344-1274 U.S.\012\012Try to find your model # and serial number if not out of warranty before called.\012 ... Maytag 24 in. MDB9750AW Dishwasher

My maytag dishwasher model MDBH979AWB3 is new. the sanitize light flickers when pushed then does not stay on. the sanitize cycle does not run.

... Maytag Dishwashers

I have a maytag dishwasher model # mdbtt70awb quiet series 300 when you push any of the wash cycle buttons nothing works. the only button that lights up is heated dry so there is at least power there. do you think the control panel is bad?

... Maytag Dishwashers

I have a Maytag dishwasher MDBS561AWW that doesn't start when the start/cancel button is pushed. Power is on. Water is on. All of the other buttons seem to function as you can cycle through all of the other settings and the lights respond.

... Maytag Dishwashers

My Maytag model MDBS561AWW won't start the cycle when you push the start/cancel button

... Dishwashers

I have a Maytag dishwasher quiet series 300. It is one year old. The problem I am having is this. After running a cleaning cycle, there is water in the bottom of the machine. If I push the start button, then cancel a few seconds later it will drain. Any idea? Thanks, Terry Roose

Hi Terry, Welcome to FixYa, I am Kelly. \015\012 A few things can cause this. Most of the time it is drain related with the Air-Gap being the culprit that is restricting drain flow. If the dishwasher drain has a restriction ... Maytag Dishwashers

I have a maytag mdb 9 dishwasher. The only cycle that will work is instawash. None of the other options light up when I push the buttons. Is there any way to reset?

... Maytag Dishwashers

I have a maytag mdb6650 aww dishwasher. The dishwasher just stopped. The light on the control panel is on. If I push the buttons to try a different cycle, the light over light wash remains lit, so the buttons don't seem to respond. I was wondering if it is the control assembly, or if the door switch is not working. The handle cracked a while ago, but if the dishwasher still worked even though the handle had cracked in half.

... Maytag 24 in. MDB6600A Jetclean II Built-in Dishwasher

I used the "rinse only" cycle on the dishwasher a little while ago. I've never used this cycle before. After dinner I tried to start the dishwasher, but no other buttons on the panel respond except the last one I used, which is the rinse only cycle. I push and push, I tried pushing and holding, nothing works, I get no lights no anything. I've been using the "light wash" cycle for a long time and I normally just push the start button and the last cycle used starts automatically, so I wasn't a

Try un-plugging the dishwasher (check for cord under the sink) or turn off the breaker to it to re-set the control board. If this does not resolve your issue you may have a defective key panel. ... Dishwashers

Kenmore 665.15912001 DISHWASHER RUNS BUT DISPLAYS ERROR MESSAGE Instead of displaying the number of minutes in the cycle when I push the cycle selector button and then the start button, it starts as soon as I push the cycle selector, without waiting for me to push start; meanwhile, it displays "_J" instead of the number of minutes in the cycle. It washes the dishes but not well, lots of food debris. Some people in this forum have described running a diagnostic on this machine; how do you do that

... Kenmore 15912 Built-in Dishwasher

I have model GU3600XTSY2. Sometimes the pots and pans light flashes for no reason. Sometimes I can push that button and it stops. However, the cycle I select to wash the dishes is constantly interupted by the pots and pans (P&P) light flashing. If I push the P&P button, the wash cycle usually starts where it left off. Sometimes it will go back to the beginning of the cycle and begin all over again and get caught in a loop; start washer, P&P flashes, push P&P, begins cycle from beginning, P&

... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

Maytag Dishwasher Stops During Cycle

... Dishwashers

Maytag Dishwasher, Quiet Series 300, Won't let us CHANGE CYCLES

... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0742 seconds