Having problems with your Maytag Dishwasher ?

Model GSD3620Z02BB - The normal cycle will not engage when the knob is turned. The short cycle will engage (sound like it is working) but the soap is left in the reservoir and about 2 inches of water is left in the bottom. Thank you for your help.


Answers :

Sounds like the selector switch has gone bad. The machine is not fully cycling thru and draining because the selector isn't proceeding like it should. \015\012
\015\012This typically happens if the selector dial is spun real hard repeatedly over time. The little cogs inside of the selector will get broken and sometimes the broken parts will lodge inside the switch and cause jams.
Repair Help & Product Troubleshooting for Maytag Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Model GSD3620Z02BB - The normal cycle will not engage when the knob is turned. The short cycle will engage (sound like it is working) but the soap is left in the reservoir and about 2 inches of water is left in the bottom. Thank you for your help.


Sounds like the selector switch has gone bad. The machine is not fully cycling thru and draining because the selector isn't proceeding like it should. \015\012\015\012This typically happens if the selector dial is spun real hard repeatedly ove ... Maytag Dishwasher

Whirlpool dishwasher: Model DU920PWKT0; 8 years old Lately, have noticed not full drainage of water at end of cycle... about 1 inch standing (thus 2 inches at the sump). Glasses have had noticeable film on them. Ran the rinse cycle a number of times to explore problem. When I interrupted the cycle, the water on the bottom was soapy, yet no new soap had been introduced. I even colored the water "left" in the tub to see if it was replaced by fresher water. Although it was going through t


Find the 'tech sheet' behind the front 'kick plate' of the machine. This doc will give you a troubleshooting procedure for that specific machine. Check drain line and make sure it's clear and not kinked. Is filter clean?Has machine ... Dishwashers

Dishwasher Issues My dishwasher is not properly dispensing the dishwasher soap. The flap on the soap container seems to be opening, but the soap is always caked in there after the cycle is finished. I have tried leaving the soap flap open, but that just seems to deposit soap particles on the dishes in the front of the bottom rack. Also, there is often a greasy film left on many of my dishes. Is this a soap issue or a water issue? I am very frustrated! Can you help?


I would try using a different soap or less of your current soap. ... Maytag 24 in. MDB4100 Built-in Dishwasher

Kude48fxbl - brand new out-of-the-box. When put through a test cycle after installing it, water poured out of the bottom left edge of the door. This was not associated with either the water input or the discharge hose, but rather seemed to come from the interior of the washer and out under the door. The door seemed well latched, and running it with some dishes in the bottom tray (not blocking the soap dispenser) didn't help.


... KitchenAid Dishwashers

Hotpoint dishwasher machine go's through wash cycle, through to the end, after dry cycle ends there is always 2 inch's of water left in it that doesn't drain out' but some water is added when new cycle is started, then throughout wash cycle whenever water drains it never drains completely, always leaves 2 inches of water before adding more water to begin rinse cycle. what do I need to do?


... Dishwashers

Subject is Bosch dishwasher SHU6800. There is a soap residue left on dishes. Residue is not visible. Using two glasses taken from a recently completed wash cycle I rinsed one under tap water and then filled glass with tap water. The second was just filled with tap water. There is noticeable soap bubbling and foam in the second glass. Starting the 10 min rinse/hold cycle following completion of a full 60 min wash cycle results in considerble soap foam in the bottom of the tub. Have tried thr


WHAT IS WRONG WITH YOUR DISHWASHER? \015\012\015\012\015\012\015\012 \015\012For a detailed Dishwasher ill ... Dishwashers

The dishwasher does not pump all of the water out. There is an inch or two left in the bottom of the dishwasher after the cycle has completely run. The control panel has been recently replaced on this dishwasher and it did not correct the problem. Help?


You likely have a dirty or faulty water level sensor in the machine that needs to be cleaned or replaced. ... Dishwashers

I have about an inch of clean water is left at the bottom of my Maytag dishwasher after the cycle ends. Help


Hi,Here is a tip that I wrote that will help you with your dishwasher not draining problem...Dishwasher Problems - Water will not drain out ... Maytag Dishwashers

Hello, I had a problem with my Bosch dishwasher not washing properly. I have fixed burnt out wires, replaced the water inlet valve, AND tested with a new control module. Nothing is helping. When I start the cycle, it completes the initial drain and water does flow into the unit for about a minute, maybe a minute and a half. I can hear the clicking of cycle changes but it is not washing. Eventually it will drain the inch or so of water in the bottom, but it never washes. Any help???


Hi,\015\012\015\012Welcome to Fixya.\015\012\015\012Can you hear the wash motor humming ? I`ve got a "pdf" I can send you regarding this if you want to contact me at ... Bosch SHU9925UC Built-in Dishwasher

Large amount of water remains in tub after completion of wash, water is draining out during cycle, dishes are cleaned, I can hear water being pumped out into sink drain as dishwater is going thru its cycle. The depth of the water is over one inch at the lowest part of tub. Water is not clean and has soap in it.


Hi.To start check the drain well, and also have a look at the drain hose at the back of the appliance.If the drain lines are OK, then you will need to replace the pressure switch, that determines when to stop pump from drainin ... GE Dishwashers

Kenmore dishwasher leaves LOTS of soap residue. We have hard water and have adjusted rinse aid level. Previously told problem wasdue to having washed dishes by hand and that dishsoap was problem. Told to run a cycle every once in a while with T of vegetable oil. Hasn't helped. Tried multiple soaps and soap amounts. Help please.


HI. You should never run any unit with vegetable oil. That was a horrible suggestion. This actually made your problem worse. With that said; This issue will be the result of a mineral build up inside all the hoses under the unit. The drain hose and r ... Dishwashers

I have a maytag quiet series 300. When it is done with any of the cycles in leaves about 1-2 inches of water in the bottom of the dishwasher. I can manually hit the start button twice and it will go through a 2 minute cycle and pump out the water. I have cleaned the filter inside the dishwasher where it drains and have checked the hose to the disposal and it pumps out fine. It just doen't pump itself at the end of the cycle. HELP!


Here it is - Maytag Quiet Series 300 Manual ... Maytag Dishwashers

I am a licensed plumber who installed a frigidaire fdb1o5rem1 dishwasher for a customer about 2 years ago. It has water to the solenoid valve and the screen is clean. I can see water coming in to the unit on left side through the port hole on the inside of the unit. Dishes do not get clean and it doesnt act like water is being distrubuted inside the dishwasher. Soap never gets washed away from door. Dishwasher makes funny sound in mid cycle like the pump is not running in wash cycle. Discharge p


I can see from what you have described (by the way it is a very clear and precise description which is very helpful), there is a problem in the water circulation system. These dishwashers use an alternating water flow method to split the water circul ... Frigidaire Dishwashers

There isabout 2 inches of water left in the bottom of the dishwasher after i run a cycle , and some food bits left in the water how do i drain the waterand remove the food bits? A manual was never left when the new machine was installed. We have a Quiet something 3 machine.


The filter is probably blocked.\015\012\015\012It is inside the base of the machine.\015\012\015\012Take out the filter and clean it and also clean out the filter well as that can also hold quite a bit of debris.\015\012\015\012 ... GE Dishwashers

Kitchenaid dishwasher - small pieces of food are left on otherwise clean dishes. Water level comes to about 1 inch below heater coil. I ran it without dishes (or soap) and added about a quart of water so that level came to about 1/4 inch below heater and that's when I noticed food pieces on drain surfaces (nylon filter under bottom spray arm unit and circular plastic "trap" surrounding it). Spray arms holes are clear and water is hot.


It sounds as if you figured the solution out. The holes in the spray arm(s) get plugged by small debris, (tooth picks, seeds, bits of plastic like candy wrappers, etc) and the water does not reach the dishes to wash and rinse effective ... Dishwashers

Put through entire cycle, standing water and dishes still wet, only 1 yr and 3 months old!WHY!!!!!!!!! It also has a musky or bad smell like food in the trash sometimes smells. 500 series 6 cycle stainless steel inside, black 24" in wall. Water is about an inch deep. Have tried it on pots and pans cycle, regular and auto, and have on sani-dry and have spot stuff in it. HELP!!!!!!!!!!


Take the drain hose into a bucket and see if it pumps out.\015\012if it does check for blockages where the hose goes to.\015\012\015\012most likely is a blocked pump, the pump is assesable from in side the sump, you may have to get ... Bosch Evolution 500 SHE45M06UC Built-in Dishwasher

Help! My dishwasher runs thru it's cycles but when I open it I find my second detergent cup still full of soap and my dishes still dirty. I have an older maytag dishwasher but have never had this problem with it. I've tried running a short prewash cycle with the soap despenser open to wash out the soap from the open second despenser but it doesn't wash it out. I know water is coming out of the spray arms but can't see if the arms are spinning although when running it does sound like they ar


Hi,\012There are three common problems that cause the Soap Dispenser or Cup not to open. I have a tip that will explain these problems in detail....Dishwasher Repair Problem ... Dishwashers

I have a Kenmore Ultra Dishwasher. The bottom arm spins, the top doesn't, although water drips out. The water fills up under the heating element. The top dishes aren't getting clean and the bottom aren't as clean as they used to be. I also noticed that the soap dispenser is open, some of the soap is gone, but there's still some soap in left in the dispenser. This never happened before and it happens all the time now. Thanks for any help you can give me!


Hi, \012I have an older dishwasher also and recently my wife alsocomplained about it not cleaning right... so me being the man I am tried invain to clean the things... Bought new spray arms online and installed them inminutes...now the thing works li ... Dishwashers

Dishwasher is not rinising properly. Frequently food left on dishes and soap residue. We have a water softner, we have been using less and less soap. Sometimes theres even soap left in the cup at the end of the cycle.


Hi,\012\012\012\012\012I\012have an older dishwasher also and recently my wife also complained\012about it not cleaning right... so me being the man I am tried in vain\012to clean the things... Bought new ... Frigidaire PLD2855RFC Dishwasher

Bosch Shu43C02UC dishwasher fills with water but the washing won't start. As the filling nears complete, a double clicking noise occurs to start the washing motor but nothing happens. The time continues to countdown but the machine is silent. When I open and close the door, the click click noise is heard but the machine is silent. I can cancel the cycle and drain the water but none of the washing or rinse cycles will activate but the timer works. The soap door even opens if the timer is left to


Have you checked the inlet water temperature is at the correct level for the dishwasher.\015\012\015\012Please provide the full model no. of your dishwasher -- Shu43C02UC /??\015\012\015\012I think the problem is linked to th ... Bosch 24 in. SHU43 Built-in Dishwasher

My 5 year old bosch dishwasher cycles to one minute and then cycles forever and ever with very soapy water in the bottom. After a very long time, the water is out of the dishwasher but soap residue is left on the dishes and the bottom ot the dishwasher.We are presently using only 1/2 teaspoon of detergent (Finish brand). I have had a repairman here to look at it, but he didn't seem confident that it was a timer issue and even though I have paid the exorbitant service call fee, I am not sure I wa


Hello,Welcome to FixYa.Based on your description ... Bosch 24 in. SHU66C05 Stainless Steel Built-in Dishwasher

My dishwasher is SHU 3000 series and over 10 years old. The problem is SUDS that will not go away. I have used on-line methods such as vinegar. I have gone through 6 bottles of "Dishwasher Magic" and have put it through cycles not using soap over 30 times and am still getting suds even at the end of the rinse cycle. I have called a local repairman and he says he cannot help me..that I should continue running the dishwasher time after time till the water is w/o suds. Any help for me?


... Bosch Dishwashers

Bosch Dishwasher model : SHV4313GB/17 The machine won't switch off and the pump is still trying to drain water ( there is no water left in machine ) The cycle seems to have finished as it has made the beep sound as if it has finished. The dishwasher is still working even when you open the main door. Have tried to reset it but to no avail. Even after turning it off at the mains it still starts up again as if in mid cycle ! HELP PLEASE


I have a SHV. My sink drain backed up, and the water accumulating in the sink then migrated to the dishwasher, through the drain pipe, causing the dishwasher to fill up and, it turned out, overflow a little. When I turned on the dishwasher, the wat ... Dishwashers

My Bosh SHX33MO5UC built in dishwasher does not empty. There is about one and a half inches of water left in the dishwasher at the end of the cycle. The water does not seep in after the cycle ends but just does not completely empty


Hi,\015\012\015\012\015\012The drain hose can cause the dishwasher to fail to drain properly. The recirculation hose can be responsible for problems with poor rinsing of dishes.To access the drain hose remove the lower panel located benea ... Bosch 24 in. SHU43 Built-in Dishwasher

We have a GE Profile Dishwasher Model GSD4430X66WW. It runs through the all cycles but at the end displays code PF and there is a couple of inches of water left in the bottom. If I hit the run cycle and then the reset, the water will drain and the code goes away. Any suggestions?


Pf means power failure. you may have a loose connection underneath where main wiring ties in in box. ... GE Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1808 seconds