Having problems with your Maytag Dishwashers ?

Machine not functioning

\015 Rotary dial control, timer is cycling, but machine is not operating. will sometime wash or rinse, then not drain. or will drain but not dry, Have moved the dial to various cycles\015

Answers :

HI, this is a damaged timer device. the mechanism has failed and , it is unable to correctly initiate the proper washing cycle. simply replacing the timer/control will fix this issue..
Repair Help & Product Troubleshooting for Maytag Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Unable to start dishwasher, only functioning light on the panel is the cancel/drain light. push that button the machine funtions for a minute or two and shuts off,also the light above normal wash is blinking. When the machine last functioned it would start with a very high decibel level.If its the circuit board I need an approximate replacement cost. Bob


If you go to searspartsdirect.com you can get the exact cost of the module. ... Dishwashers

Electronic controls the dishwasher will not turn on. press and hold the heated dry button for 5 seconds and the machine came back to normal. now even that is not getting the machine back to normal. the normal button and start buttons flash but machine does not function. i have the front electronic panel off and do have a volt meter to test if you could run me thru the proper procedures.


First thing to check is the door latch switches, and hte strike plate(metal tab protruding from the top of tub assy in which the door closes into, if bent up to high the door will not be recognizedas being closed. you can use a small screw driver nad ... Whirlpool 24 in. DU1100XTP Built-in Dishwasher

I have a Zanussi DE6850 free-standing dishwasher. Have just put on a 65 degree programme. After approximately 1 minute the machine has stopped functioning and the top two lights are flashing and water remains in bottom of machine. There's also a bad dirty water smell from machine now


Hello,\015\012You seem to have a blockage,have you checked the filters lately.Also check the drain hose and the pipe that the drain hose goes into,if they are clear then the blockage is down in the bottom of the dishwasher in the pipes or the d ... Zanussi 24 in. DE6850 Free-standing Dishwasher

The hidden control panel has only about half the lights showing what function is pressed. A couple of days ago the washer would not start. The only function which would work was the far left sensor light. After trying to cut power and pushing other buttons, to no avail, we let the machine sit a couple days. It now works again with only half the lights on function pad working. It acts like there was a electrical short.


First retrieve the tech spec sheet behind the toe-kick panel located near the floor and run the diagnostics if it will let you do so w/o the full operation of the keys on the pad,then if it wont the touchpad or keyboard on the front that you use to s ... Jenn-Air 24 in. JDB1100AWS Built-in Dishwasher

Dishes are no longer coming out as clean as they used to, especially bowls or utinsiles with dried on food. The machine appears to function ok, but is about 8 years old. The machine just seems tired. Am I looking at a worn out pump or something else?


Hello,\015\012\015\012Those are common issues with dishwasher's as they age, and very good questions. The Asko dishwasher however is a very good hi-end machine and typically good for much more than 8yrs. That being said, 8yrs. is subjective isn't it ... Asko D1706 Built-in Dishwasher

The control panel on the front of the machine will not light up and will not activate any of the functions on the dishwasher. The machine is getting power into the main connection box.


Hi,\015\012 \015\012Checked whether you have accidentally locked the control panel or not, push and hold the 3 key for 5 seconds and the dishwasher will activate. \015\012OR ... Dishwashers

My Siemens SL84A305UC/26 dishwasher will not drain. I've checked the drain and it is clear. I can hear the motor hum during the drain cycle. It will fill and wash OK, but not drain. Does this machine have a solenoid for draining and if so how do I check it? How do I check the pump to ensure it is functioning correctly? I've tried to remove the plastic bottom of the machine to see what is inside and to troubleshoot the components, but it seems almost impossible to remove. What is the trick? What


... Siemens 24 in. SL84A305UC Built-in Dishwasher

Have Frigidaire Gallery Dishwasher, model FGHD2433KW1, had to relevel machine. Got finished and the hold lock light is lit and will not go off. with this light on, machine will not function. any suggestions?


... Frigidaire FGHD2433KF Builtin Dishwasher

My 1yo slimline hotpoint dishwasher LST216 has developed a fault when trying to run the 'normal wash': washing stops after a couple of mins, the lights start flashing and the alarm comes on as soon as the water is being drawn into the machine. When I open the door I can hear a whirling/grating motor noise coming from the bottom of the machine. I have cleaned all filters and have run other programmes to check overall functionality and they all work as expected most of the time. I cannot unders


... Hotpoint Dishwashers

My Siemens SL84A305UC/21 dishwasher will not drain. I've checked the drain and it is clear. I can hear the motor hum during the drain cycle. It will fill and wash OK, but not drain. Does this machine have a solenoid for draining and if so how do I check it? How do I check the pump to ensure it is functioning correctly? I've tried to remove the plastic bottom of the machine to see what is inside and to troubleshoot the components, but it seems almost impossible to remove. What is the trick? What


... Siemens 24 in. SL84A305UC Built-in Dishwasher

Non-functional When turned on, machine functions for 10-15 seconds before stopping. It sounds like there is no water coming in. All filters have been removed, checked, and cleaned. Any suggestions?


... Dishwashers

Machine not functioning


HI, this is a damaged timer device. the mechanism has failed and , it is unable to correctly initiate the proper washing cycle. simply replacing the timer/control will fix this issue.. ... Maytag Dishwashers

I can remove the lower spray arm in the Kenwood Elite 66517262401 but cannot remove the screen to clear out debris below which is preventing the machine functioning well. What is the solution?


Found a screwdriver which was able to remove the special screws fastening the screen. ... Dishwashers

Vulcan vsa regency 500e touch control. I have light in dishwasher but when you close the door the main control panel touch pad will not function. Can't operate machine


... Dishwashers

My indesit IDL 500 dishwasher has two warning lights flashing (nos 2 & 4) but the manual gives no indication of what this means. Apart from the lights the machine appears to be functioning normally. Any ideas what this means?


... Indesit Dishwashers

Hi I have a Fisher & Paykel dishwasher model dw681es, the start & reset buttons light up but the machine won't function. Is there a special reset button or something else I can do? Thanks.


... Fisher and Paykel Dishwashers

Noticed dishes on top shelf not entirely clean. Ran machine empty and opened many times during wash. Noticed that Lower Spray Arm works as expected, but Middle Spray Arm turns only 1/8 or less, then Lower Arm spins again. Schematic with Use and Care manual just says pump motor switches from one to the other in certain cycles, but I don't see this happening. Looked for obstructions to water flow and pressure seems normal. Is control for this function part of the pump, or in the control panel?


Something could be in that checkball, see page 5 ... Frigidaire 24 in. GLDB653A Built-in Dishwasher

My kitchenaid KUDI01DL dishwasher began making a lot of noise while running, then subsequently decided not to circulate the water around to wash the dishes. It sounds like the motor is running (maybe) but there is no washing action going on. The machine will fill, drain and heat the water but nothing else. Is it likely that the pump/motor assembly has ceased to function properly? thanks...


The problem is very likely in the chopper and/or somewhat possible in the impeller. The chopper is replaceable from the front. Disassemble the pump, the chopper will be on its left side under a cover. That cover is kinda tricky to remove (remove all ... KitchenAid 24 in. KUDI01DL - Multiple Color Built-in Dishwasher

Non-functional I purchased the dishwasher to replace a very old one. I plumbed and wired it exactly according to the installation instructions. When I started the machine to test it all i get is a blinking "wash cycle" light. There is no water moving, no pump noie, nothing. I pulled it back out and double checked everything and it is all in order. Any suggestions?


CHECK FOR A FAULTY WATER INLET SOLENOID ... Frigidaire 24 in. FDB1050REC Stainless Steel Built-in Dishwasher

When I pick a cycle with my washer the lites on the door come on for a short period of time then go out.We found sequence on line of selecting various functions repeating this to reset machine,this worked for awhile but know all it will do is fundtion lites will come on when you se;ect a cycle then go out nothing happens.


Remove the touch panel and un plug ribon . clean with alcohol wipe/ reinsert and try again. this some times will correct poor connections .if this does not work the panel may be bad. . mm fed back pls . ... Dishwashers

Help! My Whirlpool Quiet Partner II isn't working at all. Water was standing in bottom at end of last 2 cycles, but on the last cycle, I came home to clean looking dishes, standing water, and a machine that won't turn on at all- no lights on any buttons- nothing works. I've tried the reset codes published here and elsewhere, but there are no lights on any buttons at all. The circuit breaker is fine. I have 3 young kids and can't function long without my dishwasher!


There is a fuse in the control panel what your model# i can get you the part number its easy to replace it. ... Dishwashers

Machine not emptying. I have checked & cleaned filter. Holding down the function key nothing happens


An engineer had to come out and found some class in the pump which he removed and the machine funtioned again. ... Hoover Dishwashers

Water will not drain/pump out of machine. All other functions seem to work fine, but water does not drain out. Problem is not in drain line. The bottom of dishwasher is clean. I wet vacuumed it clean twice


Check for clogged pipe,drain pump or timer. ... Whirlpool 24 in. DP840D Free-standing Dishwasher

A message "Error4" appears. The machine does not function at all. Power is OK


The best and at NO COST. Talk to the Organ Grinder not the Monkeys. I spoke to Candy who told me exactly the meaning of error4. I cured it instantly and If I had used Fixya they would have cost me a lot of money for no good reason. ... Candy 17 in. CS455 Built-in Dishwasher

Drainage Problems My ASKO D3120 doesn't drain properly leaving water in the bottom. I have had this problem before (2 yrs ago) and called the helpline who told me how to reset the machine by pressing the buttons in a particular order which fixed it immediately. Now when I call them they claim this can't be done and they will have to send a technician. Sounds like a money making exercise to me. Does anyone know how to reset through the programming function? Next time I'll write it down and wont h


Turn off the dishwasher by pressing the on/off switch on the top left of the dishwasher. Wait 5 seconds. Press and hold the program button on the right side of the front of the dishwasher. As you are holding the program button, press the on/off sw ... Asko 24 in. D3120 Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0691 seconds