Having problems with your Maytag Dishwashers ?

The contol lock LED is illuminated on the front panel of my Maytag dishwasher. (Neither my wife nor I pressed the control lock for 3 seconds!) We've tried to extinguish it by pressing it for 3 to 5 seconds, but it remains ON. We've turned off the breaker to the dishwasher overnight, but when we turn the breaker back On, the contol lock LED comes on. We simply can't unlock the control panel. We can tell that all of the other buttons work just fine because pressing any of them causes the 3 Sec LED


Answers :

If by pressing the control lock button for 3 seconds does not solves the problem.then there are 3 possibilities due to which this problem may occur\015\0121)the door is not closing properly. the dishwasher door latch is either cracked internally or the door is bit opened.by closing the door you will fee;l that its closed but internal door latch if cracked then sensor will not get command so the control lock light will get on.\015\0122)the internal main board is got shorted so the machine is got stuck up on stand still and control lock is not unlocking because the internal circuit is shorted.if this is the case the main board needs replacement.\015\0123)this is a rare option ,but some users face this problem too that.control lock button which you press for 3 seconds actually that button is got internally loose so nothing happens after you press it for 3 seconds.so keep it press for more then 3 seconds but very tightly without damaging the button or front panel.also press this button again n again randomly for more then 3 seconds.\015\012------------------\015\012if the door latch or the main board any of this is faulty--------\015\012you can get the replacement part from \015\012-------\015\012www.repairclinic.com\015\012or at \015\012------\015\012www.shopjimmy.com\015\012-------------\015\012thanks.this will help.please do rate the solution.thank you for using fixya.keep updated.
To unlock the control, press the “Options” and “Select” buttons simultaneously. The control lock status light will no longer be lit. If this doesn't work please give me you model #. If it does, let me know that too.. I hope this helps.
Repair Help & Product Troubleshooting for Maytag Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The contol lock LED is illuminated on the front panel of my Maytag dishwasher. (Neither my wife nor I pressed the control lock for 3 seconds!) We've tried to extinguish it by pressing it for 3 to 5 seconds, but it remains ON. We've turned off the breaker to the dishwasher overnight, but when we turn the breaker back On, the contol lock LED comes on. We simply can't unlock the control panel. We can tell that all of the other buttons work just fine because pressing any of them causes the 3 Sec LED


If by pressing the control lock button for 3 seconds does not solves the problem.then there are 3 possibilities due to which this problem may occur\015\0121)the door is not closing properly. the dishwasher door latch is either cracked internally or t ... Maytag Dishwashers

The control lock light goes on as soon as I press the cycle to start the dishwasher. The dishwasher does not start, presumably because the control lock stays on. I do not know how to disable the control lock function. Pushing and holding the button for 3 seconds does not disable it.


Hello &\015\012Welcome to FixYa\015\012\015\012To unlock the\015\012controls press and hold the HEATED DRY button for 20seconds. If the problme\015\012returns then only option is touch pad replacement. Please get back t ... Maytag Dishwasher

I have a Whirlpool dishwasher model #DU920PFGQ4. The controls locked light is flashing, and when I press the air dry key for 5 seconds it won't unlock, however the cancel/drain light starts flashing. When I press the cancel key the controls lock light will stop flashing, but will resume as soon as I release the cancel key. I have tried disconnecting power for 24 hours, but as soon as I plug it back up it does the same thing. Nothing else on the control panel will work.


... Whirlpool Dishwashers

I have a Maytag dishwasher MDBM601AWW. The control lock on the control pad will not unlock. I replaced the electronic control board and it worked for one wash. Control lock engaged again. I shut down the power and pressed the control lock for 3 seconds as directed by the owners manual. No luck. Please help Rich.


You have to power the unit back up and then holld the lock in for three seconds, if ths does not reset it then the console not the control bord needs to be replaced it comes with a new touch pad ... Dishwashers

The dishwasher will not turn on. The light is on where it says "to lock controls press 3 seconds" How do I unlock the controls?


Try holding the "lock controls" button in for 3-5 seconds, until the light goes out. On our dishwasher, the light for the lock-out feature is not on the button itself, but on the far left of the panel. ... Dishwashers

I have a Whirlpool Energy Star dishwasher (no clue what the model is). Door will not latch. Inside of door says to press and hold ''Heated Dry'' 5 seconds to lock control and repeat to unlock. This is not helping. We rent and do not have a manual. Please help.


Happened to me today. After much head scratching I found that the screw attaching the unit to the underside of the kitchen counter had loosened and was preventing the door from closing all the way. I tightened the screw and was back in business. ... Dishwashers

I cannot unlock the controls on the panel - i just bought a house that has the whirlpool gold quiet partner dishwasher and when i press any button nothing happens but says controls locked - i unlock the controls and try to turn on the dishwasher and still happens and says controls locked again. can you help?


Try turning the circuit breaker off for 30 minutes. Then turn back on and see. If it keeps locking you may need new control console. Hope this helps. ... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

The controls on my GE GLD4600N10WW have on occasion locked up. In the past, I have resolved this by turning the breaker off and back on. It has now locked up, but won't reset. When the breaker is turned back on, the dishwasher control panel lights indicate "Normal Wash" and "Heated Dry" but the controls do not respond. After several minutes the lights simply go dark. It does not respond to any button pushing.


... Dishwashers

When I press the start/resume control, the dish washer start/resume light blinks 2 to 3 times, then turns-off. then the dish washer beeps several times; however, the dish washer does not start. when turned the breaker switch off and on, and then I press the start/resume control, the dish washer go through a normal wash cycle. The next day when I press the start/resume control, the same thing happens. 2 to 3 blinking lights followed by beeping for several seconds. Dish washer does not start


... KitchenAid KUDC10IXSS Builtin Dishwasher

Lock Control I don't have a manual for my dishwasher. The Lock button is on (top of dishwasher). I have pushed that top button for 3 seconds. The button on the top and the "L" then both blink. The button on the top then stays on and the "L" light goes off. Since I can't get the lock light to go off - - my dishwasher won't tun on. Thank you very much.


First try unplugging the washer from powerpoint for 30secs..this may disable lock.if not, some washers will still work on lock if you hold the buttons you need. for 5seconds. eg try starting washer as normal but hold the button for 5secs....(Ps you m ... Jenn-Air 24 in. JDB1050AW Free-standing Dishwasher

Baumatic (BKD62SS or BKD62W .3) Dishwasher will not do a normal load but will run in a strange start up mode I found. When I press the power button, select a cycle, then press start the dishwasher will no longer do anything. 5 seconds after pressing start it will make a light hum noise, a little like heating water. After about a minute the dishwasher won't have done anything. It will then beep 30 times with the third led on the set of four (don't know what it means) will flash a lot. The beeps t


... Dishwashers

Kenmore Ultra Wash Dishwasher Model 665.15779 LOCK ON light blinking on control panel, unable to use washer. If buttons were locked, LOCK ON light should be lit continually not flashing. If you press and hold NO HEAT DRY button to disengage lock, nothing happens. If you press the CANCEL button it begins to blink in unison with the LOCK ON light. How can I stop the light from blinking to allow button function again?


... Kenmore Dishwashers

Hi I have a Jenair JDB1090AWS Dishwasher, that seems to be in locked mode (flashes 5 times when I press the start buttom). I tried holding the Heated Dry down for 3 seconds like it says in the manual but nothing happens. I even cut power to the dishwasher for > 30sec, still no joy. The dishwasher is still locked. How do I unlock it? Chuck Olson


Hello Chuck,. When these appliances work like they are supposed to they are great....... that being said lets see if we can unlock your dishwasher.\015\012\015\012Since the heated dry button doesn't unlock it, lets try the energy saver ... Dishwashers

I have a Kitchenaid Dishwasher Model KUDC25CHSS1. (Manual says KUDC25CH). The Delay Hours button is stuck on 2 hours. The manual says to cancel it, press it until no lights are on, but when we press it, the Child Lock light comes on. I tried pressing Energy Saver Dry to cancel the Child Lock, but that didn't cancel it. I tried turning off the circuit breaker for 5 minutes, but the same light(s) come back on when I re-set it.


... KitchenAid 24 in. KUDS01FLSS Built-In Dishwasher

Our Ikea Nutid Whirlpool dishwasher locked up recently. It started when someone was wiping off the top of the door where the control buttons are located. The dishwasher was locked on the china setting. Holding the cancel button, shutting off the breaker did not seem to clear it. Is there a way to reset the dishwasher? There was flashing on buttons but I cannot remember how many flashes or what one was flashing.


... Whirlpool GU2400XTP Built-in Dishwasher

GU1500XTLS3 Periodically won't start. Dishwasher has power because pressing cancel causes dishwasher to start draining (even though there is no water). Door switch works because opening door prevents starting drain cycle. No other button on control panel will work except for the 'air dry' / 'lockout' button. Turning off circuit breaker for 15-30 minutes and then turning circuit breaker back on seems to fix the problems but only for a couple uses and then it stops working again. Need ad


This could be the 'fill switch', which is the level sensor. Could be a plastic tube that exerts air pressure into the tube as it fills, make sure it's clear and open. The dishwasher has a sensor that monitors the door being closed too. Some use a hig ... Dishwashers

For the GE 24 in. GLD5560LSS Stainless Steel Built-in Dishwasher, I reset the breaker on the service panel, the unit is on but I press a wash cycle and press start and nothing happens. Is there a fuse inside the control panel of the dishwasher?


... GE 24 in. GLD5560LSS Stainless Steel Built-in Dishwasher

Kudl03fv883 The dishwasher will not start. When I press the Start button, the green LED comes on, but then starts to blink within a few seconds. I close the door, but the dishwasher does not start. The Start LED just continues to blink.


... KitchenAid Dishwashers

Our Kitchenaid dishwasher model # KUDP021R will not start. We close door, select wash and press start. The control lock light at the top which is lit flashes a few times and then stays lit. Dishwasher remains silent. An aside which may be helpful is that the door has always seemed to be not quite straight...as though it had to warp a tiny bit to close and lock.


The problem you have already identified could be the door switch is not closing when you shut the door. Please confirm your dishwasher is KUDP02I (i and not 1).\015\012\015\012One way to check is find out the door switch on the door panel ... KitchenAid Dishwashers

I have a MDB6759AWS3 that is one year and two months old. This morning I went to the control panel to press the buttons and some would light up and others would not. I disassembled the inner panel and looked at the "computer like" flat ribbon that connects the control panel to the main circuit board and noticed that some of the wires in the flat ribbon had deteriorated. I put it back together and pressed the buttons and they flash very dimly for a few seconds and got the dishwasher working bu


You may want to check the warranty iif it is a maytag or whirlpool, some have a 5 year warranty on the control and board. If not you can go to www.searspartsdirect.com to l ... Dishwashers

Whirlpool dishwasher model GU1500XTLSO Control panel is mostly not responsive. Can enter "control lock" mode by pressing and holding "air dry". If I press air dry again in this mode, the green button flashes three times. Does this mean anything? I would really appreciate some help.


... Whirlpool Dishwashers

Lock on led keeps flashing. Can not cancel it, when pressed it also starts flashing. Control touch pad not functioning. When able to get going usually after turning off power for a while, it does not complete the cycle and the lock on led starts flashing again. Thanks


Hi,\015\012The flashing lock light problem might be caused by a stuck key on the touch panel console.If the control board detects that a key is stuck, then the dishwasher will suspend operation until the key is unstuck. If a key without a ... Dishwashers

My Frigidaire dishwasher PLD4375RFC0 won't lock so it won't start. I select the normal wash and start and close the door and the led light shows the minutes but it doesn't lock and after a few seconds the led light goes out and nothing happens.


... Frigidaire PLD4375RFC Dishwasher

Our GE built in dishwasher Model GHD6310L18WW had no lights on and would not operate. i checked the breaker panel and found it was OK and 120vac were flowing to the unit. i then turned the braker off for 30 seconds then back on .this made the time remainig LED display sow 106 and the Normal wash Cycle LED is lit as well as the extra Heat LED . the unit will bot operate though


... GE Dishwashers

My serial #TH24050632 has an occational control board failure and requires a reset. That is my current problem. In the past I turned of the circuit breaker for thirty minutes, and then pressed sertain control buttons inseries or at the same time for ten to twenty seconds. I have misplaced the information I wrote down to correct my problem. Can you help me with the correct procedure to reset my control panel? Thank you.


Check if this works.\015\012\015\012Press normal wash and heated dry one after the other about 5 times.All lights on panel will light.Wait until all lights go out and it resets itself.It will go into a mode on it's own.Then press cancel a ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1922 seconds