Having problems with your Maytag Dishwashers ?

Won't start my "lock on" light is on but when I press any buttons nothing happens.


Answers :

Press and hold the No Heat button to unlock.
Repair Help & Product Troubleshooting for Maytag Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I just bought this house with this dishwasher built in. I have pushed the door shut, pressed the heat dry button to lock the door and pressed the start button. Nothing happens. Now I can't even get the lights on front to turn off. The lock button flashes as though the door is open, but its not as far as I can tell. I have to press the latch in to open the door. I'd like to use it... any ideas. Its a Kenmore Elite model # 665 17052 402. Thank You


... Kenmore 24 in. 17052 / 17054 / 17059 Built-in Dishwasher

Whirlpool dishwasher model GU2-400-XTB7 Problem started with display cycling through delay times. (1 hr, 2hr, 3 hr and so on.) Was able to cancel that for short periods and then it would repeat the cycle. Was able to run dishwasher by pressing different buttons. Then it would start a cycle but did not run full cycle. Now control panel doesn't work at all. When buttons are pushed, lights do not light up and nothing happens. Is stuck in lock mode.


... Whirlpool GU2400XTP Built-in Dishwasher

Kenmore Ultra Wash Dishwasher Model 665.15779 LOCK ON light blinking on control panel, unable to use washer. If buttons were locked, LOCK ON light should be lit continually not flashing. If you press and hold NO HEAT DRY button to disengage lock, nothing happens. If you press the CANCEL button it begins to blink in unison with the LOCK ON light. How can I stop the light from blinking to allow button function again?


... Kenmore Dishwashers

Dishwasher: Kenmore ultra wash sensor quiet guard plus. I'm in a rental so I don't have the manual or model number. A few days ago it just wouldn't start the wash cycle. When you press normal wash then start the no heat dry and lock lights flash every other second or so but nothing happens. I can hit the cancel button and it will make sounds like its trying to drain, and after about 5 minutes stops. I've done the heated wash/ no heat dry sequence to try to reset but no luck. Also tried turn


... Kenmore Dishwashers

I have a KitchenAid KUD1021RWHO dishwasher that will not turn on when I hit the start button. The LED lights work when I press cycle selection ie. "normal" but when I press the start button nothing happens. I have waited for a couple of hours and then it will start. However during the last week it has happened more frequently and now it has not worked for the last (2) days. Any ideas as to what the problem may be? Thank you for your help!!!


Hello,\015\012\015\012This is a very common issue on these units. The touch pad has failed. You can try to flip the breaker off for several minutes and see if that clears the code. More than likely the touch pad will need to be replaced.\015\01 ... KitchenAid 24 in. KUDI02IR Built-in Dishwasher

I have a F&P dishwasher model DW60CDX1 (around 5 years old) which we cannot start a cycle. The dishwasher turns on (power button and all programme indicators light up) but when you press a programme button nothing happens - the lights don't change. We have switched the power off at the powerpoint and on again a few times but this has not rectified the problem. It was playing up before this in that sometimes the programme would not start when a button was pressed but I just closed the door mor


The micro switch in the door which senses the door closing has probably failled. This is accessible once the inner door cover is removed. Switch should be under $10 from electrical store. Or buy through appliance manufacturer. ... Fisher and Paykel Dishwashers

Won't start my "lock on" light is on but when I press any buttons nothing happens.


Press and hold the No Heat button to unlock. ... Maytag Dishwashers

I have a 1 year old maytag dishwasher and it has the touch buttons on top of the door . When you touch the buttons to turn it on, nothing happens. It will light up the type of wash you want e.g. heavy,light...., but it won't start when pressed. It will cancel when pushed, but can't get it to start. HELP!!!


... Maytag Dishwashers

Zanussi zdt6053 in built dishwasher not starting. When pressing the control panel on/off button the 65 deg normal wash light comes on. When pressing the program selection button nothing happens. When closing the door the machine does not start up. Is there a fault in the control panel circuit board? Would water pressure prevent the machine from operating?


... Zanussi 23 in. ZDi6053SX Built-in Dishwasher

My dishwasher will not start. The 3 second button light is on and when I press it nothing happens . I try pressing any other button and nothing works


It sounds like you have "locked" the dishwasher. This was an added feature that most people never wanted since it only seems to be set by accident.Try pressing the 3 second button and holding it down for at least three seconds. This sho ... Maytag MDB7100AWB Dishwasher

When I try to start the dishwasher, nothing happens other than lights come on for the buttons pressed. I tried other options other than the usual "normal wash" and still nothing happens other than the lights come on. I have a Ge Profile model #: PDW8480J10SS. Any suggestions? Thanks.


Did you accidently hit the start time delay button? ... GE 24 in. Profile PDW9880JSS Built-in Dishwasher

I have a Frigidaire FDB956rbc0 model. When the start/cancel button is pushed nothing happens. There is power and other buttons cause lights above what is pressed come on. Delay wash works but when it starts the washing light flashes. I have run a test on the cycles by pushing start/cancel and power dry button during power failure mode. all cycle run properly. Any thoughts?


... Frigidaire Dishwashers

Hi i have a smeg df 410 sdx 450 wide dishwasher that is coming up to three years old ,the fault it has developed is that it wont switch on ,press the button and nothing happens,no lights or the normal beep.240v is getting to the button and when the button is pushed on 240v comes out the other side and goes to the various pcb's but the appliance wont do any thing,can you please give me some ideas.


... Dishwashers

IDL700 wont start Kept getting error message to say there was a blockage. Checked all the pipes and pump, all fine. Now the blockage lights are out, but the machine wont start at all, just beeps when I press the start button, then nothing


Sorry to read about your problem, I hope this helps you out.the blockage, maybe inside the pump of the unit, or at the check valve.I suggest you contact a service company..I tried to help you. Please help me and Ra ... Indesit 24 in. IDL700 Built-In Dishwasher

Kenmore Elite Dishwasher Model # 665.15914 Selected wash cycle...lights come on...pressed start...nothing happens...after about 10 seconds wash cycle lights go off... Is start button broken? What to do?


... Kenmore 15914 Built-in Dishwasher

Gu2800xtvso When I press the start but it flashes and nothing happens. I then press the cancel button and the clean light starts flashing


... Whirlpool Dishwashers

I have a Tecnik TKD795/3 built in dishwasher. It is now making a gurgling noise as though it is draining water when I try to start the cycle, but the cycle does not start and no lights come on at all. I have tried pressing the outside two buttons to reset, but absolutely nothing happens and the gurgling noise continues until I release the power button. Can you help please?


... Tecnik 24 in. TKD795/3 Built-in Dishwasher

After selecting a program, the dishwasher beeps for a while and the 3 buttons on the left flash too. Program wont start, water wont fill and nothing happens. THe lights keep flashing but the beeps stop for about 30 secon ds then start again. Help me Please.


Basically the dishwasher is telling you there is a fault - Not so useful I know! Plug out the machine and leave it for five minutes and see will it reset. If that does not work, you will need to reset it manually. To do this consult the manual. If yo ... Hotpoint 18 in. DC28 Slim-Line Built-in Dishwasher

We ran the dishwasher and it ran fine, but now the green light for the Heated Dry setting won't go off, and if we press the Start button, nothing happens. If we press other buttons, a flashing "L" appears briefly.


Please post the model of the dishwasher. ... Maytag Dishwashers

MDB7809AWB2 When i press a cycle, the buttons light up , BUT nothing happens when i press start.


... Maytag Dishwashers

I have a Whirlpool model DU1055KJVQ1, Type 575-0 under-counter dishwasher which is less than 2 years old. In the last couple of weeks, it wouldn't start intermittently, and I would need to hit cancel on the keypad, and then restart. Now that doesn't work. When I try and start the dishwasher, it doesn't work. I press Normal for the cycle, heated dry for the Option, and then hit Start. The buttons light up for 20 seconds or so, nothing happens and then they go out. Any ideas?


... Whirlpool Dishwashers

My kenmore dishwasher mod #665 17332400 isn't starting. you can press the wash selection buttons and they light up and you can push start but nothing happens - after a while it does start to do something that sounds like it wants to run then it sort of stops. Any help?


... Kenmore 24 in. 17332 / 17334 / 17339 Free-standing Dishwasher

Dishwasher is a whirlpool DU940QWDB3. When yu press button to start washing, lights go on but nothing happens. Where should i start trouble shooting this? Thanks


Dear Sir:see the wiring diagram attached.1) I recommend the switch door, if are open the machine will not close the starting relais as you will see in the diagram.sincerely. God bless you. ... Whirlpool Dishwashers

I'm not able to reset my dishwasher Whirlpool ADG795, i mean, my 4-year old son was playing with buttons and, i think, the dishwasher went, but not exactly properly, into test, all the lights are flashing, i was trying to start the test properly (by pushing power button for 30 sec, hen 3 sec release and press once more) but unfortunately nothing has happened, argh... any idea?


Sounds like you are in the testing/diagnostic mode. You can exit the program by holding the buttons, or simply unplug the unit for an hour, in meantime of being unplugged, press and hold the function or power button for 5 seconds, then wait 1/2 hour ... Ariston Technologies Dishwashers

I just installed a whirlpool du1055xtss3 dishwasher......the lights blink however when I press the start button nothing happens...I have turned the electric off and then back on ...there is hot water and still nothing


Hi,\015\012\015\012Could you kindly tell me which Light is Blinking? Is there any Label on \015\012it? any Sequence?\015\012\015\012Let me know, so that we could proceed.Hope i helped you.Thanks for usi ... Whirlpool Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1617 seconds