Having problems with your Maytag Dishwashers ?

The dishwasher cycles are slowing down and the dial seems to be staying in one location too long.


Answers :

HI. This is a strong indication of timer failure. The timer motor is damaged. This will cause a weak, or no forward motion of the timer dial. This will, also, disrupt the normal flow of the cycle, as well.I would advise to replace this damaged timer control device asap. Once replaced, the unit will operate correctly.
Repair Help & Product Troubleshooting for Maytag Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The dishwasher cycles are slowing down and the dial seems to be staying in one location too long.


HI. This is a strong indication of timer failure. The timer motor is damaged. This will cause a weak, or no forward motion of the timer dial. This will, also, disrupt the normal flow of the cycle, as well.I would ... Maytag Dishwashers

Kenmore Dishwasher model 665.1675592 doesn't seem to wash as well as it used to. Seems to have a low water level. Filler valve works, allows water in, but never seems to fill enough. No spray reaches top shelf, I think due to insufficient water level. It's like the timer doesn't stay on long enough for it to fill. Also cycle time seems WAY up, but if the timer is slow, how does it time out filling so fast? Looks like it would be slow all the time. Suggestions?


... Kenmore Dishwashers

I have inherited a Blanco Bfdw 650s Dishwasher and there seems to be a manual dial as opposed to automatic ones which is what I'm used to...does this mean I have to stay home to help the machine perform it's cycle??


No! Set the cycle you want first (A/B/C) THEN turn it on. It will just run through. I've just found my PDF instructions and trying to work out a way to upload them. ... Dishwashers

During power scrub cycle which is the one we use most of the time the dishwasher stays at one minute fot a long time. the dishes come out clean and it finally does finish cycle just dont know why it takes so long on last minute of cycle for so long


It's just heating the water more ... Bosch 24 in. SHU43 Built-in Dishwasher

Candy cs455m the dial goes through one cycle but it stops when it gets into another cycle and there seems to be no heat because when we stop the cycle and open the door the plates are cold and the water has not been dried off


\015\012\015\012\015\012Welcome to fixya.\015\012\015\012I'm Huuum at your service.\015\012\015\012You said, The dial goes through one cycle but it stops when it gets into another\015\012cycle and there seems to be ... Candy 17 in. CS455 Built-in Dishwasher

Hi. After completing the wash and rinse cycles, my Frigidare FDB750RC dial stays stuck just before begining the drain and drying cycle. If I turn it one click, then it drains and finshes drying cycle fine.


... Frigidaire 24 in. FDB750RC Slim-Line Built-In Dishwasher

Dishwasher problem Our Asko 1353 dishwasher stops halfway through its's wash cycle. I suspected the thermostat, as it seemed loose in it's holder and not tight against the tub. After I tightened the holder the problem is still the same. Also, the on/off switch (pressure switch?) does not stay in the on position and when I looked it over I found one of the crimp on terminals had melted. Short circuit? Too much resistance from bad thermostat? How do I check the thermostat before I order a new one?


I think your switch may just be bad,but to check the t-stat remove both wires and use a multimeter,set the meter to ohms and connect the two leads to the terminals on the t-stat.with the t-stat to off you should read an (ol) open condition,when you t ... Dishwashers

My 5 year old bosch dishwasher cycles to one minute and then cycles forever and ever with very soapy water in the bottom. After a very long time, the water is out of the dishwasher but soap residue is left on the dishes and the bottom ot the dishwasher.We are presently using only 1/2 teaspoon of detergent (Finish brand). I have had a repairman here to look at it, but he didn't seem confident that it was a timer issue and even though I have paid the exorbitant service call fee, I am not sure I wa


Hello,Welcome to FixYa.Based on your description ... Bosch 24 in. SHU66C05 Stainless Steel Built-in Dishwasher

Bosch SHU4302 DW has a leak in the bottom left. I cleaned the gasket etc. but no luck. Slow leak drip by drip in the wash cycle. This model does not seem to have the steam vent that other Bosch models have. I can clearly see the water past the gasket on the left, but not the right. But the gaskets on left and right seem to be located identically. Any help in resolving is appreciated. Best Regards


I've got a 4306, and while it never leaked, the bottom door gasket did seem to chemically melt over the years.I replaced it a few months ago. I don't know that a steam vent is needed as the gasketing system never allows any steam pressure ... Bosch Dishwashers

Blowing fuse... We've replaced the overheating fuse located in the control board area about 5 times. It has just blown again after using the dishwaser one time--before it would go about a month before blowing the fuse. It seems to get about a few minutes away from completing the wash cycle and does not complete the draining process. Help!! We don't know what to do next--replacing the fuse is costing about $15 each time, before you know it we could have bought a new one! Thanks for the help. Ti


Tim, this blown fuse issue was pretty common on this model. Whirlpool, which made this model came out with a fuse kit that included a terminal and heavier guage wire to eliminate this problem. It just splices right into the control board, easy job. T ... Kenmore 17024 Built-in Dishwasher

My dishwasher is seeming to stay on the wash cycle. How long is a normal wash cycle?


Dishwashers today use a lot less water and energy to do this they filter the water like crazy this makes the wash times go way up, the motor used today uses only a little power so a long cycle does not cost much. They average wash time fo ... Kenmore Dishwashers

Dishwasher has very very long run cycle. Dishes come out hot so I'm assuming the water is heated enough, & T stat tests ok. Seems if we advance timer manually it will finish otherwise seems to stay about in the center position on timer.


... Bosch SHU3036UC Dishwasher

I have a SHU43C05UC/22 Bosch dishwasher that runs fine till it gets to wash then it seems to stick there. the timer times down to 1 and it stays there for a really long time. it doesn't appear that the washer ever gets out of the wash cycle. when you stop/open the door there is still soapy water in the tub. You can cancel the program and it will drain the tub fine then you have to select rinse and hold to clean out the soap out.


... Bosch 24 in. SHU43 Built-in Dishwasher

HELP!!. Have an old smeg dishwasher - SNZ10. We turn it on, and it goes, but the dial never moves on through the cycles - it just stays stuck wherever you have turned it to. Does seem to be heating and water coming in. Husband grumpily doing dishes by hand! HELP!!


After a while thje dial on Dish Washers, wear out and jam, It sounds like it needs a new Timer, However if it's old, I would replace the Dish Washer. ... Smeg CSU2001 Built-in Dishwasher

My smeg dwf 64 sse blew the main fuse yesterday. The machine was up to its rise stage on program 8 then the breaker went. Every time I switch the main back on it blew. I have managed to stop it blowing the panel but now it seem to be stuck mid-cycle and won't complete. There a re all sorts of noises and the 1st led stays on then the 3rd one illuminate. Any ideas?


Your element was initially short circuit, which caused circuit breaker trip. It is now open circuit and timer will not advance because water has not reched required temperature, recommend thermostat replacement also. ... Dishwashers

I have a Bosch dishwasher (SMI5072), bought in 2005 second-hand but working OK. It has always been a little slow to get going, and I had initially thought the clockwork program dial was getting stuck. Then I concluded that it had something to do with the filling up process, and I thought it must be because the water was rather cold and paid no more attention to it. This has meant that it seemingly takes ages to get through a cycle. Yesterday I put it on, left it and got on with some work. An h


There is a screen inside your water inlet valve that may be clogged. You will need to see if you are getting power to the water inlet valve when the machine calls for water. If you have power replace the water inlet valve ( not uncommon in older Bosc ... Dishwashers

Bosch diswasher It takes almost 4 hours to run through a full cycle. It seems to stay in the rinse/dry for too long.


Not sure but it could be that the washer thiks it needs water (i.e. the water us syphoning out as it is coming into the dw. I hav a fairly new Sears Kenmore and the problem was that the drain hose not eleveated enough. My fw is on main floor and drai ... Bosch 24 in. SHE44C02UC / SHE44C06UC / SHE44C07UC Built-in Dishwasher

Smeg Allegra We start our Smeg Allegra with a 'dial' control. It has started to get stuck, and unless nudged forward, will stay on the same wash cycle permanently. never switching itself off. Is there an easy remedy to this, or do we have to bin it and buy a new one?


... Smeg 24 in. DWF1 2 Free-standing Dishwasher

We have a model #SHX57c it is about 3 years old. It is now taking forever to complete its cycle, seems to stay on 1 minute for a long time. The dishes come out wet, not very hot inside.


... Bosch 24 in. SHX57C05UC Stainless Steel Built-in Dishwasher

Whirlpool Quiet II (DU110XTPB1)... Two problems (maybe it's one)... Start/resume light flashing and won't stop. I have tried on the different button combinations from this website and other websites and none of them seem to make a difference. The flashing continues. That's problem number one. Problem number two is that it seems to go into some sort of washing cycle in completely random intervals. When it's in one of the random washing cycles the following lights are on; Normal Soak and scour


Hope it's under warranty, maybe logic board, poor motor design causes main PCB failure ... Dishwashers

Dishwasher stalls I have a Bosch dishwasher model # SHU4006UC/U06. The dial stops after going through one cycle and the dishwasher continues to run that cycle and will not advance unless we manually advance the dial. After advancing the dial the dishwasher will stall until we have manually advanced the dial until reaching the "9 o'clock" position. It will then continue until the dry cycle is complete. Thanks!! I have the same problem. I took out the timer control and spraid it with contact clean


If the cycle doesn't complete, check these:Water-heating cycle ... Bosch SHU4006 Dishwasher

Dishwasher stalls I have a Bosch dishwasher model # SHU4006UC/U06. The dial stops after going through one cycle and the dishwasher continues to run that cycle and will not advance unless we manually advance the dial. After advancing the dial the dishwasher will stall until we have manually advanced the dial until reaching the "9 o'clock" position. It will then continue until the dry cycle is complete. Thanks!!


The Timer might not be bad. If one of the two thermostats is bad, the Dishwasher will exibit the same symptom. The thermostats are 141 deg. F and 161 deg F.They only cost $20 each. The Control Module is close to $200. ... Bosch SHU4006 Dishwasher

KitchenAid KUDP01DLBS2 dishwasher. Runs for a very long time on any cycle; time does not seem to advance. (takes 2.5 hours or more for normal cycle. "sensing soak", "water heating" lights on for a long time, even though it appears that water is not being heated. Checked incoming water temp, is hot. Did not do this when new, something has changed. Typical cycle was 1 hr 10 min. before.


Sounds like the heater inside the dishwasher is not working. The machine is trying to get the water up to a preset temperature, probably in the neighborhood of 140 degrees. That is one of the things that it is sensing.After the machine fi ... Dishwashers

My Omega Eurolux Dishwasher (mode: DW211P/1) won't stop cycling, It sems to get stuck during the wash cycle and continues for hours, until I turn it off. If I turn the dial to rinse it rinses fine. It doesn't seem to heat the water at all, there is no steam when I open the door. I have put a new heating element in, but this doesn't seem to be heating up at all. When I open the door mid wash cycle the element is cold to touch.


... Dishwashers

Problem to turn on the KitchenAid dishwasher, model #: KUDP02FRSS1. I have this machine for over 2 years. After one year, sometimes, I cannot touch the touchpad to select some option of the cycles and options. Shutoff the power, and wait for few hours, it seems to work. Unfortunately, now the only cycles I can turn on is "Heavy Duty" and I can not hit Start to start the cycle. The other option on the touch pad I can select is the "Cancel". I turned off the power this time for 2 days and it seems


The electronic control board is most likely the issue. I would replace the pab that controls the dishwasher functions. The control board controls the cycles and the wash time selection as well as the on/off function of the dishwasher. ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1528 seconds