Having problems with your Maytag Dishwashers ?

Maytag Model No WU202 is running through all cycles but is not pumping out the water from the tub. I can hear the pump running and a gurgling sound. Could it be the micro mesh filter that is plugged? Any detailed drawings available of the lower wash assembly and instructions to take it appart? This machine is more than twenty years old.


Answers :

Hi,

It sounds like your belt broke. Open the bottom access panel below your door and check.

The part is :-

http://www.repairclinic.com/SSPartDetail.aspx?PartID=2814&PPStack=1

If you take off the front lower panel under the door, the broken band is likely sitting right on the floor. Its probably too old and loose to last long but its working at themoment. If it breaks or keeps falling off there are replacement bandsavailable.

Let me know, if needed further assistance.

Hope i helped you.

Thanks for using ' Fixya ' and have a nice day!!
Hi there,\012

Please check out the following -

A clog in the drain line or air gap (if there is one) is the usual reason that a dishwasher won't drain. Often the problem is at the point where the drain line attaches to the garbage disposer or household drain line. If you remove this line, you can clear any debris from the hose or hose connection. Be sure to reattach the hose before starting the dishwasher again.
Then check Your dishwasher pump ejects the water. The pump is usually mounted directly to the motor, then attached to the bottom of the dishwasher. You can reach the pump from inside the dishwasher, but first you need to remove the lower rack, the spray arm, and the spray arm support.
Look for an impeller--a round plastic fan blade-type of device that spins around. This is the wash impeller, which forces the water through the spray arm. Beneath the wash impeller is the drain impeller, which is similar in size and shape to the wash impeller. The drain impeller pushes the water toward the drain port. These components make up the pump. If any of the pump components are defective, you need to replace them.

Please post comments for more help or information............

Good Luck!!

Thanks
Repair Help & Product Troubleshooting for Maytag Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Maytag Model No WU202 is running through all cycles but is not pumping out the water from the tub. I can hear the pump running and a gurgling sound. Could it be the micro mesh filter that is plugged? Any detailed drawings available of the lower wash assembly and instructions to take it appart? This machine is more than twenty years old.


Hi,It sounds like your belt broke. Open the bottom access panel below your door and check. The part is :-http://www.repairclinic.com/SSPartDetail.aspx?PartID=2814&PPStack=1If you take off the front ... Maytag Dishwashers

I want to inspect filter on Whirlpool DU1055XTSS2, but can't seem to remove the lower wash arm assembly. The top of the lower spray arm hub just spins and spins.


... Dishwashers

I have a Bosch SHE46CO dishwasher that runs too long. It adds an extra 37 min to the normal wash cycle. It counts down correctly until about 50 min then it adds the 37 min. Also when it get to 1 min it continues to run for at least 15 min. I have cleaned the filter and the upper and lower arm.


It can be the software or anly have a much colder water and it needed a longer time to heat for washing and rinsing. also a heater is damaged and the dishwaser runing at the half capacyty. so long! ... Dishwashers

I am washing my house with the washer wide open to 3/4 open. It will run fine and hard for 4 to 7 minutes then bog down and shut off. It has new fuel, spark plug and the air filter is clean. What else can I do??


... Pressure Washers

Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher The lower drawer won't complete a cycle. It will fill and empty 4 or five times in succession then continue to wash for about 15 mins the it starts to fill and empty as before. On a 36 min Eco cycle after 1 hr it still shows to have 15 mins to the end of cycle and wants to run forever. I have swapped the control boards to no avail.


Http://www.retrevo.com/support/Fisher-&-Paykel-DD603-Dishwashers-manual/id/20093dj878/t/2/\015\012 ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

I have a Whirlpool ADG937 dishwasher (9 years old) which will not complete a 65c wash cycle. It starts Ok and runs for a long time but then continually bleeps, when I open the door the programme indicator light is on the rinse cycle. If I reset the programme to 65c it may do the same or occasionally it will finish the cycle. I have tried salt top-up, descaling and filter cleaning all to no avail. Is the programmer faulty (can I bypass it?)or should I replace the washer?


... Whirlpool Dishwashers

All aspects of the dishwasher work except the wash motor/pump does not run. Is it the motor? I have taken the lower arm assembly apart and removed the support to spin the impeller. It spins fine although there is axial play.


If the shaft is moveing from side to side you need to replace the motor. did you tern the impeller around about 3 complet terns? ... Dishwashers

Kenmore model#587(Frigidaire) leaks under door. New install. Had machine for a year plus before install. took off front panel- can see water squirting past lower door gasket as wash arms rotate. cause is water running down door during wash cycle piles up in the channels molded into the lower left & right side of the wash tub and pushes out the sides of the lower gasket. looks like a design issue- called SEARS, they just want to sell me a new gasket! go figure. any ideas on a fix?


It does sound like an inner door seal ,however If you get upset at Sears and complain they may help you as they say the squeaky hinge gets the oil..And with Sears the more you squeak the better your chances of results ...Good Luck ... Dishwashers

My lower rack will not clean bowls or cups and I have to be very careful how I place plates. The serviceman has been out twice and I have run vinegar through multiple times with no improvement. My top rack is working fine. I have tried running it on different settings and we have verified that the lower wash arm seems to be spinning. The temperature seems to be fine. Even glasses placed on the lower rack that weren't very dirty seem to have a scum in them when finished. Any ideas?


Hi, \012I have an older dishwasher also and recently my wife alsocomplained about it not cleaning right... so me being the man I am tried invain to clean the things... Bought new spray arms online and installed them inminutes...now the thing works li ... Dishwashers

Hi - I have tried all the usual tricks of running an empty load with vinegar, and the food particle filter seems to be the kind that isn't removable. Whenever I run a load, there is enough left over particles on the dishes - especially the top shelf, that I either have to wash all the glasses by hand, or run at least one more cycle. I have a standard size hotpoint built-in dishwasher. Please let me know if there is a way to clean the filter, or an alternative method so that the dishes are a


The best but not the fastest way is to remove the pump and motor assy and visuall inspect for fooreign items in the pump assy and also inspect for damage to the pump inpeller at the same time. Sorry not a fast fix but the best way ... Dishwashers

Have SHU43C and have had no problems with it. We usually run it on the Quick Wash cycle, but ran it on the Regular Wash cycle yesterday because the glasses seemed to be coming out spotty. After it ran, there were no lights on the display like there usually are. The washer had run and the dishes were clean, but it has not drained completely. There is still about an inch of water in the bottom, despite removing and checking both the Large Object Trap and Fine Filter (neither which were clogged


The drain pump needs to be replaced or cleared of obstruction. ... Bosch 24 in. SHU43 Built-in Dishwasher

My 1yo slimline hotpoint dishwasher LST216 has developed a fault when trying to run the 'normal wash': washing stops after a couple of mins, the lights start flashing and the alarm comes on as soon as the water is being drawn into the machine. When I open the door I can hear a whirling/grating motor noise coming from the bottom of the machine. I have cleaned all filters and have run other programmes to check overall functionality and they all work as expected most of the time. I cannot unders


... Hotpoint Dishwashers

No water I have the kenmore ultra wash quiet guard built in. You can hear the motor running but it is not drawing water into the machine. I have checked all of the hoses and connections and they are good....pump sounds like its running but just wont draw the water in.


Inlet solenoid not working, check wiring is attached ... Kenmore 24 in. 15932 Built-in Dishwasher

Replacing filter gasket assembly part # WD22X10043 with new unit. Can you tell me how to uninstall the lower spray arm and Filter assembly without damage?


... GE Dishwashers

I have a whirpool Quiet Partner III, and the top layer of glasses is not getting clean. I had a technichian out some time ago, and the problrem was caused by food debris trppaed in the filter in the wash module. He saud it was easy to clean that out, so I have removed the lower spray arm, but cannot undo the 4th screw that will allow me to take the grey round filter cover off to remove the food or paper debris. It is under the white flat pipe that delivers water to the wash module, and I cannot


I had same problem, would not clean well and fixed it. . I cracked open the door during wash cycle and used screwdriver to defeat the door lockout. The water from the bottom sprayer was only shooting half way to the top of dishwasher. To fix I remove ... Whirlpool Dishwashers

I have a KUDS03CTWHO KitchenAid dishwasher. It started not cleaning the upper tray well a few weeks ago and now the lower one is not getting cleaned very well either. I have disassembled and cleaned the 3rd level , upper and lower spray/wash arm assemblies as well as the feed tube assemble. These were not blocked or glogged. There appears to be less spray coming out of the upper and 3rd level spray arms they before but as I said there is no blockage. I also cleaned the bottom filter. There has b


\015\012Hi\015\012\015\012The issue seems to be with the float switch\015\012assembly that is bad and should be replaced. Please check this ... KitchenAid Dishwashers

My kitchenaid KUDI01DL dishwasher began making a lot of noise while running, then subsequently decided not to circulate the water around to wash the dishes. It sounds like the motor is running (maybe) but there is no washing action going on. The machine will fill, drain and heat the water but nothing else. Is it likely that the pump/motor assembly has ceased to function properly? thanks...


The problem is very likely in the chopper and/or somewhat possible in the impeller. The chopper is replaceable from the front. Disassemble the pump, the chopper will be on its left side under a cover. That cover is kinda tricky to remove (remove all ... KitchenAid 24 in. KUDI01DL - Multiple Color Built-in Dishwasher

My bosch sgs5312 dishwasher seemed to complete its washing cycle (Zero with a dot on the display), but the pump still seemed to work for hours. Tried to re-set to no avail. Cleared filters and the pu


... Bosch Dishwashers

Dish washers wash cycle dose not run if i unplug ribbon to circuit and plug back in it runs fine


... KitchenAid 24 in. KUDM01TJ - Multiple Color Built-in Dishwasher

My dishwasher spray arms were clogged with calcium buildup so I cleaned one and replaced the other. I also removed the fixed disc-shaped device underneath the lower spray arm and found the particle filter was clogged- so I cleaned it out. The dishwasher ran fine for a few times but then the filter clogged again, and again, and again. Now I need to make a routine of disassembling the parts to get at the filter every week because the filter no longer clears itself during the wash and/or emptying c


You may want to check your hot water tank. It may need drained and cleaned, Or you may have the rod in the tank disintegrating. Also check you water faucet areators to see if they have calcium pieces too. ... Maytag Dishwashers

Upon selecting a wash cycle and closing the door the machine starts normally (heating water stage) but never clicks to allow water in and wash the dishes. Fails to advance to the wash cycle and just runs without doing dishes. There was water in the bottom after the last wash, filters are clean?


... Bosch SHV46C03 Built-in Dishwasher

I have a craftsman Pressure washer Model 580-725400 the unit has ran great until today. I last used the unit 1 week ago with no problems but now I have to run the machine almost full choke to get it it rev up and run smooth. The engine oil is clean and filled to the proper point. The spark plug is new and gapped proper. The air filter is new also. And the gas is 97 Oct and fresh. When it choke it to crank the engione I move the choen to run and the engine struggles to run. When I move the choke


... Craftsman Pressure Washers

Ref: NEFF Dishwasher S5555XOGB/70 (FD No. 8602) Problem: Does not drain at end of wash cycle. Checks/Symptoms: 1. No blockage in whole of drainage system, system and filters are clean. 2. Pump does operate mid wash cycle ? drainage tube can be felt pulsing and pipe gets warm right through to the main drain connection at the ?U? bend. 3. At end of wash cycle the pump appears to still be trying to run but there is no flow, even when the door is opened. If machine is emptied by hand the pum


... Dishwashers

Hi, I have an ASKO D3250 dishwasher and it keeps stopping during the wash cycle and flashing the heavy pots and pots symbol simultaneously. I tried cleaning the filter basket and found a little plastic part floating in there that has printed on it PP-T20. I don't know where this piece goes or if it's even the culprit. There is a little bit of water not draining from the filter area when I unscrew the outer filter basket, I cleaned it out, but when I re-run it, it still stops and gives the dual f


The part is a cap for the drain pump. You can put it back into position by removing the filters and placing it to the left of where the circular filter would be positioned. The part goes in with the part numbers on the bottom facing down. When posit ... Asko 24 in. D3530FI Built-in Dishwasher

Our bosch dishwasher runs but no water is spraying on the inside. Is there a water filter clean out or is there a water pump that might be broken? I checked the line coming in and it isn't plugged. I made sure where the stainless line goes into the electric valve that it wasn't plugged to that point. I could see anywhere else to check if it was plugged. I figure there has to be a water pump, but I guess I'm not sure of that either. Thanks for any help..


Hi, welcome to Fixya. \015\012 \015\012By the description you've provided, it sound's like the wash motor is either seized or just stuck, let's hope it's the later. \015\012 \015\012Bosch had issued a service tip about this ... Bosch 24 in. SHE43C05UC Stainless Steel Free-Standing Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1547 seconds