Having problems with your Maytag Dishwashers ?

Does not fill with water to start, water on , power on


Answers :

If the machine is not filling with water, the water inlet valves could be stuck or just bad. You can test power to them with a voltmeter. If no power, then you likely have a bad relay. Could be bad control board, but leave that for last possible cause. If you do have power to the valves, then valves are shot.
Repair Help & Product Troubleshooting for Maytag Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Maytag Model MDB7160AWW S/N 10337613WQ Symptons: Fills with water OK, shuts off water OK, does not start any cycle, or drain. After a power off/power on reset, problem remains. Flashes CLEAN & LIGHT WASH. My understanding is this is an error condition for low motor current, which makes sense as the motor never starts. I know both door switches are good (I checked them with a DVM) and both engage when the door is closed. Tripping the water float switch opens the valve and water fills the tub


... Dishwashers

KitchenAid KUDL03IVWHO Machine seems to stop after the initial water fill. There is power to the machine, the door latch circuity is working, all the buttons on the control pad light up. After selecting any of the wash cycles and pressing start, the washing light illuminates and the machine fills normally to the point where the fill valve stops the inflow of water. At this point the machine stalls, it does not start the cleaning process. I can press cancel and the machine drains normally. I e


Hi,\015\012\015\012You have got to the correct resolution. This is a circuit or most commonly called the board problem. Please find the bellow mentioned link which will help you to get one compatible for your washer.\015\012\0 ... Dishwashers

I have a zanussi ZSF2440 dishwasher, when it turned on by the power button on the front you can choose a cycle and start it, Once the cycle is started it fills up with water but doesn't stop until it over flows setting off the flood protection, which cuts the power, so all the lights on the display go off and stops the water flow and drains the dishwasher and keeps draining the dish washer while the flood protection is on. It seems as if the dishwasher doesn't know when its reached its correct


... Zanussi Dishwashers

My Miele G641 displays the Salt PC light even after filling it with salt. I have to cycle the main power switch 3 or 4 times before the Start light will come on. Then when I press the Start button it momentarily pumps out water and then stops. Sometimes the Start light stays on and I can get it to give the pump another brief spurt, but often the Salt/PC light comes on again and the Start light goes out. I then have to re-set the power switch. How do I tell if the logic board is fried?


Hi.This is not a PC, when logic board is fried the machine does not start at all rather than doing weird thing.The logic board is not fried, in the worst case the salt sensor is jammed. Try first pouring a couple of litres of hot wa ... Miele 24 in. Novotronic G641 Plus Built-In Dishwasher

I have the GE Quiet Power 3 Model gld4400n10bb. When I start a wash I can hear it fill with water (to about 1/2 inch below the heating element). It then waits for about 5-7 minutes and pumps the water out. It fills again several times and pumps out. It doesn't sound like it is washing though. The whole interior of the dishwasher is covered with dried soap. I can also tell that water is not spraying around the whole interior. Any ideas?


... GE GLD4400NWW / GLD4400NBB / GLD4400NCC Dishwasher

I have a GE GSD2230Z00WW dishwasher water will not fill on start no power on the fill valve either. Water will come on quick wash cycle and rinse.


Make sure you get water to the\015\012dishwasher. Check to see if the water shut-off valve (located under the\015\012sink) is open. If you get water to the dishwasher, but there is still\015\012no water inside during the fill cycle, the problem might ... GE 24 in. GSD2220Z Built-in Dishwasher

Bosch SHY66C My Bosch dishwasher won't fill with water.  All electrical connections are fine and I can hear it make a sound as if it is trying to start about every 2 minutes.  There was water in the bottom so I used a shop vac and pulled it all out but it still won't start and is doing the same thing.  I checked the solenoid with a multi-meter and it appears to be working.  My power went out last night for about two hours and that's all I can think of that might have affected it.  The dishwasher


I'm a novice on this question, but i agree with the above statement about check the stuck float switch or check for a bad safety switch or lockout switch of some sort. I would suspect something is definately faulty in that area. Will the dishwasher r ... Dishwashers

Triton dishwasher (GSD5110) won't fill with water. Unit is getting power and pressing start opens the soap dispenser, but water doesn't fill. Any ideas?


... GE 24 in. GSD5110 Built-in Dishwasher

It starts running then stops - starts pumping in water then stops, etc. burning plastic smell near top... doesn't leak, gets power, but begins to fill, then stops - might start to drain (pump), but then that stops too...


... Frigidaire 24 in. PLD2850 Built-in Dishwasher

CI am having a problem getting our Miele G575 dishwasher to run through a wash cycle. It definitely has power, the water is on and there is no water in the bottom of the dishwasher. When you turn the dial to start a cycle, it hums but doesn't fill with water and doesn't progress through any cycle. We have tried all positions of the dial and have had no luck? Any ideas??


You said it does not progress...meaning the dial does not eventually move? it may be waiting on a water level sensor to be tripped. The dishwasher is just not filling. The water valve solenoid may be stuck or defective. or a wire may have come of ... Dishwashers

My gas power washer will not start. I filled the gas, checked the oil, set the choke, made sure it was on, changed the spark plug, checked the air filter, and drained any water. When I pull the cord to start I don't even get a putter. Anything else I can try or do I need to take it to a service place.


Will it run if you pour a small amount of gas in the carb? If so, it's a fuel supply problem. Most likely a stuck closed float needle. ... Honda Maxus Pressure Washer MX5222

FDB520RHS2 Dishwasher Same problem as posted. Dishwasher has power & water - control panel lights are on, when start is pressed the sound of a relay can be heard but nothing else happens - no water fill no cycle. Unit stays in this condition without running.


... Frigidaire FDB520RHS Full Console Dishwasher with 4 Wash Cycles 4 Wash Lev

Does not fill with water to start, water on , power on


If the machine is not filling with water, the water inlet valves could be stuck or just bad. You can test power to them with a voltmeter. If no power, then you likely have a bad relay. Could be bad control board, but leave that for last possible caus ... Maytag Dishwashers

I have a Whirlpool Gold Quit Partner III, model GU1100XTLB1. When I run the normal cycle it functions well until near the end. At that time the unit stops and the pots&pans indicator light blinks. If I hold the cancel button in the unit drains then refills and the light starts to link again. I don't know how to reset this unit because I only have air dry. If I leave the power off for a day I can get the unit to reset. If not, it just fills back up with water and the pots&pans starts blinking aga


... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

Our Frigidaire dishwasher, Model # FDB2410LDS0 has power and will start on any cycle, but after filling with water, there is a pause and then the lights just start blinking and it stops at around the 92 mins remaining display. We have tried shutting the breaker off for 10 mins, then back on, hoping to reset it with no luck. Any thoughts?


... Dishwashers

Kenmore Elite 665.17053400. Powers up ok, fills up with water ok, but wash cycle won't start. I can hear the motor trying to turn but sounds like its seized up. If I cancel the wash, the machine drains out the water ok. Does this sound like the moter is shot and if so, what should I expect to pay to have it replaced?


This dishwasher has a very sophisticated wash system. In order to improve the wash efficiency it uses a chopper and a soil sensor. It is very likely the chopper assembly is clogged which is blocking the water from circulation and straining the wash m ... Kenmore Dishwashers

My sound conditioned Whirlpool dishwasher is real old. It fills up completely with water. It looks like it will overflow, so I stop it. I thought it always started washing from the start. Do they always fill completely up with water, then start washing. I never noticed. I am afraid the water will overflow. Can it? Last time I ran this, it had a real loud motor. I used to hear the motor running from the start, but now I don't, just water filling up to what looks like overflow if I let it. I baile


... Whirlpool 24 in. GU2500 XTP Built-in Dishwasher

Our Matsui MF160 will not stop beeping. When you put the power on it beeps continuously. It comes on and hums but doesn't start, no water comes out. The Salt and Rinse Aid lights were on at the beginning but we have filled both of them, the lights are now off, but the beeping continues?? Can you help?


... Dishwashers

Bosch sgs6302gb I have this model dishwasher and did not use it for 1 year. I started it yesterday and found that after filling the water for 10 seconds the dishwasher suddenly stopped working. The power is there but the drain sounds which it normally makes in the begining is not happpening. Kindly help


The first thing that works is the drain pump at beginning of cycle check pump for blockage, if ok check voltage to pump , if you do not understand this answer leave well alone. ... Bosch 24 in. SGS45E02 / SGS45E08 Exxcel Free-standing Dishwasher

I have a model SHE 44 C05 UC/40. It is three years old. It starts up fine, fills with water and goes into the wash cycle. Then it continues to wash indefinitely, even though the electronic timer display counts down to 1 and sets there. It still continues washing until you turn it off with the power button


... Bosch Dishwashers

How do I reset a Whirlpool Quiet Wash Plus 930 Series dishwasher after it stopped working? Filled up with water, didn't drain, I disconnected everything and reconnected, I have power but it won't start? Thanks


... Whirlpool 24 in. DU930QWD Built-in Dishwasher

GE Profile dishwasher GSD4920Z02BB. When wash cycle starts, water starts filling tub, then drain opens and starts draining, as water continues filling. Water level doesn't get high enough to allow


... Dishwashers

I have a ASKO D3432 The pump starts when the cycle starts, empties out all water, fills with water and then stops. Error message is Water Inlet Fault. ???? But the water is filling and there is no crimps etc on the water supply line. Save me.


... Asko D3432XLSS Stainless Steel Dishwasher

My Delonghi Dishwasher keeps turning off. The dishwasher is turned on at the power point. The water is turned on. Okay When I press the POWER botton on the front it wont stay on. I have to keep my finger on the POWER button and then press the START button for washer to work. If I do this it will then pump out any water in the bottom and start to work. ***BUT when you take your finger of the POWER button the washer just turns off and stops working. Do you have any idea what could be the problem p


Yes, the power button is faulty. by pressing the power button forcefully, you are in effect allowing the contacts to close. Replace it. ... Dishwashers

I have an Electrolux ESI 6104x. Regularly just after starting the dishwasher as it starts to fill for the first time the water inlet cuts out. If you turn the water off at the mains disconnect the inlet pipe (spilling a bit of water in the process) reconnect the inlet pipe and turn the water back on the dishwasher fills and runs perfectly. This fault used to happen occasionally and now happens regularly.


Disconnect the fill pipe from the back of the machine and you should see a small mesh strainer in side the dishwashers inlet valve. Check that this is not dirty - to clean it pull out the strainer and rinse under the tap. ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1024 seconds