Having problems with your Maytag Dishwashers ?

Dishwasher is giving E1 which according to the manual is water sorce is off. We recently had turned the water off for bathroom repairs but the water has been turned back on, we have disconnected the pipes to run the water through, this is happening but as soon as reconnected to the dishwasher it doesnt work


Answers :

Hi,

This is common, there may be a flood protection device that tripped in the line or sediment got into the system when the water was turned back on.

First turn the water off to the dishwasher. Take the hose or pipe off at the connection under the dishwasher, put a pan or towels under that open pipe. Slowly turn the water on and flush that line until clear. If no water comes out then you will need to do this but further back 'upstream'.

Once water comes clear, turn the valve off again reconnect the pipe/hose to the dishwasher and very slowly open the valve. If the water does not enter now you have sediment in the water inlet valve on the dishwasher itself and that valve will need replaced.
Repair Help & Product Troubleshooting for Maytag Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Dishwasher is giving E1 which according to the manual is water sorce is off. We recently had turned the water off for bathroom repairs but the water has been turned back on, we have disconnected the pipes to run the water through, this is happening but as soon as reconnected to the dishwasher it doesnt work


Hi,This is common, there may be a flood protection device that tripped in the line or sediment got into the system when the water was turned back on.First turn the water off to the dishwasher. Take the hose or pipe off at the ... Maytag Dishwashers

I have an Electrolux ESI 6104x. Regularly just after starting the dishwasher as it starts to fill for the first time the water inlet cuts out. If you turn the water off at the mains disconnect the inlet pipe (spilling a bit of water in the process) reconnect the inlet pipe and turn the water back on the dishwasher fills and runs perfectly. This fault used to happen occasionally and now happens regularly.


Disconnect the fill pipe from the back of the machine and you should see a small mesh strainer in side the dishwashers inlet valve. Check that this is not dirty - to clean it pull out the strainer and rinse under the tap. ... Dishwashers

De Dietrich Dishwasher - DVH 610 JUI - when turned on to any programme and started automatically tries to drain water instead of filling with water. Was disconnected and filters checked and were clean. when turned on again it worked and when disconnected to be brought back into house it again tried to drain water instead of filling. All lights come on except blue light. Does not accept engineer code given with wiring leaflet


... Dishwashers

I have a CDF8 348 dishwasher. We went away on holiday and it accidentally got switched off mid cycle. When we got back and turned it back on there is a continuous beeping noise and the water doesn't seem to be getting through. The water pipes are working.


You need to unplug unit wait 12 hrs for ICs to Drop overload then Plug Back in. ... Candy Dishwashers

Belling Dishwasher IDW450. When turn on power button it starts bleeping. About 25 times. The you can select your program, it sounds like it is draining but then doesnt do anything else. Cant hear any water running in. I have turned the power off and back on. Water is connected


When you say you have turned the power off and back on. do you mean the switch on the appliance. if so turn off the power by removing the fuse from the fuse panel for the dishwasher. wait about ten minutes, put the fuse back in and see if that res ... Belling 24 in. IDW603 Built-in Dishwasher

Hi, we have a Bosch Exxcel dishwasher which mid way through a cycle a button saying Check Water came on. we turned the machine off and opened the door and found loads of water in the bottom. my husband then scooped all the water out and cleaned filter in the bottom, where we did find some bits of plastic from the kids yoghurt pots, and took the water hose off the back and checked for blockages, which there was none. the water is certainly coming from the water pipe through the hose as we tested


Check your water level sensor. And also check to make sure that your pump is working correctly. It sounds like a couple of different things that need to be addressed. First check the water level sensor. It is a tube that is located from the back of t ... Bosch 24 in. SHU43 Built-in Dishwasher

Dishwasher sounds as if it starts cycle, then stops, bleeps, and Fat and prewash lights come on. Manual says to turn off machine, turn off tap, wait 30 seconds and turn it all back on, but it doesn't make any difference. Manual says 'If the above does not solve the problem, check that the water feed pipe is not blocked' however, it doesn't say where this is, or how to do it. Please help!


Hi.You need to check the water inlet hose, that is the hose connected to house water faucet at the back of the dishwasher.Checck for blockage in the hose and ensure that the inlet hose is not blocked or kinked.If t ... Hotpoint 24 in. FDW60 Free-standing Dishwasher

Disconnected dishwasher and moved out in order to tile the kitchen floor. Ten days later reconnected dishwasher. Turned on water supply to leak check -- no water is getting into the washer. - Ran hot water from sink side to see if that would help, no such luck - Disconnected water line and water is in the line up to the connection point at dishwasher. Looked inside valve of dishwasher for obstruction - no such luck - Disconnected both ends of water line and blew in line to check for obst


... Bosch Evolution 500 SHE45M05UC Stainless Steel Dishwasher

There is a hole in the gray pipe running from the back of the dishwasher that drains the water. How do we disconnect it from the dishwasher? Is it standard where we can buy it locally?


... Thermador DWHD64 Dishwasher

I have a brand new Blanco dishwasher but im unsure if it is a DWF6XP, DWF4X or DWIN7 model. It does not have a salt dispenser if that helps. Last night when running for the first time i had a plumbing issue where the drain pipe was not set high enough as it states it has to be 500 to 100cm of ground height. Also had a leaking sink drain pipe. Fixed all that and turned machine back on and it pumped all the water that was inside to drain. I have cancelled the program and restarted but now it is ru


Unplug it and wait 5 minutes. Plug it back in. This will reset the machine. Put it on full cycle and allow it to do a full cycle. It should work just fine. ... Dishwashers

I have Frigidaire FDB956RBC1 diswasher. I have to turn off the water to fix the faucet. When I turned the water back on, water did not go to the diswasher when I used it. The diswasher runs normal except with no water going into it. The water runs find at the facet. There is separate water supply underneath the sink for the faucet and the diswasher. I wonder if there is a mechanism with the dishwasher that stop the water from going into the dishwasher after the water supply been turn off. I did


FRIDG... EXPERT HERE \012\012\012Welcome to fixya\012\012Hello\012\012 \012\012 ... Frigidaire FDB956RB Built-in Dishwasher

I was replacing my sink faucet today and in the process turned the water off to the dishwasher. Subsequently my girlfriend ran the dishwasher without the water on! Now when I go to run the dishwasher no water comes out (meanwhile I've turned the water to the dishwasher back on). Is there some kind of reset? I accidently touched the coil in the bottom of the dishwasher just after trying to run it and it was hot. What do you recommend? Thanks. Mark


Hi,You need to investigate the following :-\015\012\015\012\015\012\015\012\015\012Drain line/air gap\015\012\015\012A\015\012clog in the drain line or air gap (if there is one) is the usual reason\015\012that a dishwas ... Kenmore Dishwashers

Disconnected the dishwasher for three weeks while kitchen remodeling was going on. We now have hooked it back up and it will not work. It will turn on, but the water flow isn't working. What do you think could be the issue?


Check water control valve it has a screen inside of it or it may be bad ... Siemens 24 in. SL34A006UC Built-in Dishwasher

Champion dishwasher we have a champion freestanding dishwasher at my church. after the cycle is completed, the pressure guage behind the washer still shows 25-30 and it contnues to spray water. not forced by the motor, but more like a stuck open fill valve. if i turn off the water and run it, then turn the water back on, the valve is closed and does not let water freely in. butif i run it with the water on, it will continue to spray in freely after the cycle light goes out and you open the door.


If you turn the unit off from the circuit breaker will the water still run?if so the guts inside the solenoid valve are worn.you can call champion and get a kit to replace the worn parts and its not difficult to do.hope this helps. ... Dishwashers

We have a Model 587.1440*, 587.1441* Kenmore dishwasher. I had turned the water off to the whole house when we left for vacation and openned one faucet so the water pressure would be off the house while we were gone. Upon our return, I turned the water back on but the dishwasher gets no water. ?? What happened? It was working fine when we left, now no water. ?/


First, have you run it long enough to purge the air from the dishwasher line?\015\012\015\012Secondly, the solenoid valve for the water inlet may be stuck due to no pressure on it while you were gone. Tapping it with something light like ... Dishwashers

Hello, I have a Neff Dishwasher S5453X1GB/74 and it's not draining the water out at the end of the cycle. I have unscrewed the filter and released the impeller. I have also cleared the waste pipe that runs to the sink waste and put loads of cleaner in the dishwasher. The pipes seem to be clear as water goes somewhere during the cycle but backs up at the end. A few times when I started a cycle the water did not spray out but I could here the drainer or motor? running. I jetted water through th


... Neff 24 in. S5453X1 Built-in Dishwasher

When we turn on the dishwasher there is no water entering the appliance..then it cycles to drain the water and I reset it so the pump doesnt burnout...what could this possibly be and is there some troubleshooting I can do before I call a repairman..the dishwasher has a touchpad front...by the way..the water is turned on..


... Maytag Dishwasher

No water in the dishwasher Bosch SHX43M02-48. We turned of the water and forgot to turn it back on and ran the dishwasher. Now the it will not let water in?


Hi, \015\012\015\012By the information you've supplied, I'd guess you burnt out the coil in the water/fill valve by running it without a water supply to the valve. Are there any other unusual symptom's or error codes ? i.e. drain pump running none s ... Bosch Dishwashers

ASKO 1905 - Turn the dishwasher on and no water seems to be entering the d/washer. Water is turned on. Dishwasher gets very hot as no water is coming through the pipes.


... Asko Dishwashers

Inlet/Drain light is on. I have cleaned the drain pump and non-return valve, rinsed under water, removes all foriegn objects, turned the drain pump impeller (which turns freely) and carefully replaced the non-return valve and secured it with the locking clamp. I tried turning off the dishwasher and teuned it back on. No warning light shows but as soon as I try the dishwasher on a wash cycle it fails to pump water into the machine and release the washing tablet door. The programme unit makes a no


Is the water inlet turned off by chance? Is there no water at all inside the dishwasher? ... Miele 24 in. G643Vi Plus Built-In Dishwasher

I HAVE A BOSCH SHU5305 DISHWASHER THAT WHEN IT IS TURNED ON IT WILL NOT DRAW WATER FOR THE WASH. IT JUST SITS THERE AND HUMS. HAD A BIT OF WATER FROM THE SINK BACK UP IN THE DISHWASHER AND SPILL OVER ONTO THE FLOOR YESTERDAY. I CLEANED THE DISHWASHER FILTER WHICH WAS COMPLETELY CLOGGED. I THINK THE DISHWASHER WORKED FINE PRIOR TO THIS INCIDENT BUT THIS COULD ALL BE COINCIDENCE. I DON'T KNOW IF I HAVE A PLUMMING PROBLEM OR A WASHER PROBLEM. THE SINK WATER WORKS FINE. I CHECKED THE ON/OFF WATER VA


If the solenoid valve is humming and calling for water, you probably have a plugged screen in the valve, some you can get to and clean, some you have to replace. ... Dishwashers

Our kitchen drain clogged recently and water drained back into our VUD141 dishwasher. A plumber cleared the drain, and turned on the DW - which pumped out the standing water. But now, we have no water flowing into the dishwasher. The drain pumps, the heater works, but there's no water supply. The plumber who cleared the drain said he didn't DO dishwashers, and I cannot locate the owner's manual since we prepared for a move.


Hi\015\012\015\012 \015\012\015\012When the dishwasher won't fill and the water supply is on,\015\012then the issue is with the water inlet valve which is either clogged or\015\012blocked, you can try to clean it. If this wont so ... Viking 24 in. Professional Series VUD141 (Ultra-Premium) Built-in Dishwasher

Hi I have a Meile G 685SC Dishwasher. It has a water inlet problem. It will not fill and just keeps cycling through the water filling process with the water inlet light flashing. I have taken off the inlet pipe and removed and cleaned the inlet filter and washer and put them back. The filter was blocked with a sand like substance. I have taken apart the antiflood valve also attached to the inlet pipe but it is gel sealed so unserviceable. The inlet pipe itself on removing from the vlave appears


Check that the stopcock is opened fully or whether the water inlet hose\015\012is kinked...Check that the water inlet filter is not clogged and clean\015\012it, if necessary, as described in the operating instructions....Check\015\012that the drain p ... Miele 24 in. Incognito G643SCVI Built-in Dishwasher

Bosch dishwasher model shx36l fails to stop pumping. The drain was clogged. I cleared the drain. Dishasher backed up, water overflowed. Clog has been fixed. Dishwasher will not stop trying to pump water out. There is NO water inside dishwasher. I wish to run another load however unit fails to respond. Pump is operating even when front door to doshwasher is open. Turning the power button to OFF is the only remedy to stop drain pump from operating. How to fix?


... Bosch Integra® 500 SHX46A0 Dishwasher

My bottom dish washer was draining the water on the top dishwasher and there is always water left over on the top.I remove the pipes and put CLR to clean up drain.Start both dishwasher on rinse cycle ( 12 min cycle) then at 10 min.they start blinking with a No tap (may be water ) sign on it. I run the cycle again now a F1 sign coming with a tool sign.And both dishwasher going crazy ,it turn on by itself even I powered them off.


Hi\015\012\015\012\015\012Thanks for using FixYa. F1\015\012error means that the flood switch has been activated. You'll need to reset it by poweri ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1821 seconds