Having problems with your Maytag Dishwashers ?

My maytag dishwasher. The main wash that holds the soap does not open during the cycle. So the dishes are not getting washed!


Answers :

Hi,
\012Here is a tip that I wrote specifically about the soap dispeser problem in dishwashers...
\012
\012Dishwasher Repair Problem Detergent Cup does not Open
\012http://www.fixya.com/support/r4225828-dishwasher_repair_problem_detergent_cup
\012
\012heatman101
Repair Help & Product Troubleshooting for Maytag Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Maytag model mdbtt70aww. After the end cycle. open the door and found detergent tab on the bottom and the main wash cover is opened. Maytag diswasher model MDBTT70AWW. Put dishes and so forth in the dishwasher. Put detergent tab and jet-dry rinse agent in the pre-wash section. and close the cover. Start wash cycle after done over door and found the detergent tab on the bottom new the heater. The cover to the main wash is opened. Dishes are are clean. Wish someone would tell me


... Dishwashers

My maytag dishwasher. The main wash that holds the soap does not open during the cycle. So the dishes are not getting washed!


Hi,\012Here is a tip that I wrote specifically about the soap dispeser problem in dishwashers...\012\012Dishwasher Repair Problem Detergent Cup does not Open\012 ... Maytag Dishwashers

Frigidaire dishwasher 15 months old. just started not washing dishes very well. set it for high temp wash. put plenty of fresh dishwashing liquid in. the unit goes thru a full cycle. you open the door and dishes are still dirty. there is always lots of dishwash liquid in the door. some of it runs down the inside of the door of the unit. just does not use all of it so dishes dont get cleaned. what could it be?


First I would check to see if it is getting enough water. There is a screen in the water inlet valve that tends to pick up debris. Follow the links Di ... Frigidaire Dishwashers

Dishwasher problem It is a "classique" dishwasher , about 8 years old, but used only about 50 times max. The dishes are not getting out clean - the washing powder is smeared over them. Most of the dish washing powder (or tablet, tried it both) is not comming out of the powder compartment, despite the fact that we find the compartment open when the washing cycle is done. Sure it is just a "smal quick fix thing" but have not idea what it could be. Pleaseee help!


... Dishwashers

Ref: NEFF Dishwasher S5555XOGB/70 (FD No. 8602) Problem: Does not drain at end of wash cycle. Checks/Symptoms: 1. No blockage in whole of drainage system, system and filters are clean. 2. Pump does operate mid wash cycle ? drainage tube can be felt pulsing and pipe gets warm right through to the main drain connection at the ?U? bend. 3. At end of wash cycle the pump appears to still be trying to run but there is no flow, even when the door is opened. If machine is emptied by hand the pum


... Dishwashers

The door that releases the detergent in a Maytag Jetclean Dishwasher EQ Plus is not opening. The prewash side has openings that allow the detergent to dissolve, but the main wash side never opens preventing the dishes from getting washed thoroughly. Any ideas?


There is a spring mechanism that is located behind the flap, inside of the door of the dishwasher. You may have a spring broken in there. Take the plastic cover off the inside the door and examine ... Maytag Dishwashers

Whirlpool Dishwasher detergent door not operating properly. Main wash door opens immediately after starting dishwasher. No pre wash cycle. Loud humming noise coming from bi-metal switch or wax motor attached to the detergent cup assembly. I just replaced detergent cup assembly including the wax motor and I still get a loud vibrating humm from the actuator. model number du1055xtp3


Pdemaio,ngafm at your serviceI believe the loud humming you describe is an electronic problem. And is not worth changing parts randomly and spending unnecessary funds in this fashion!my advice is a hands on experi ... Whirlpool Dishwashers

My GE Dishwasher Mod# GSD4200J ran continuously for 4 hours only getting halfway through a cycle. Sounded like it was continuously in the wash cycle. When I opened it, soap dispenser had opened and dishes were clean. Water still in bottom of tub.


... GE Dishwashers

I have a Triton dishwasher. Last cycle, it completed washing then started drying and started beeping and the drying light is flashing. When I finally opened the latch, the beeping stopped, but the drying light is still flashing. The dishes were clean and warm - they air dried the rest of the way. I have not been able to get the drying light to go off. I have turned the breaker off over night, and flipped back on. The dishwasher goes back to flashing washing, and then clicks to drying and th


Hi,\015\012Make sure the salt level is ok - add 1Kg of salt if you have not done it in a while, and check rinse-aid level if apliccable.\015\012\015\012If this does nothing, then remove the lower kick panel for access to a data shee ... GE Dishwashers

When my dishwasher completes its cycle, there is powdered detergent left in the dispenser and the dishes aren't as clean as they use to be. This started happening after I ran a HI TEMP WASH with a SANI RINSE cycle. I'm thinking that either the detergent dispenser door is opening late or the water is not getting hot enough. To check the dispenser door, I left the door open and just poured powder into the dispenser compartment. This did not improve the cleaning.


Hi\015\012 \015\012Dishwashers use Bi-Metal strip to allow the dispenser to open/close. This strip when heat up causes the soap door spring to open up the dispenser. If this strip is not heated doesn't allo ... Kenmore 16372 / 16374 / 16379 Built-in Dishwasher

I have a Bosch DLX Series (SMU4092UC/14) dishwasher that I can't use because the detergent dispenser doesn't open automatically during the wash cycle so the dishes only get sprayed with hot water but no detergent. Is there a fix for this? Or is it time to get a new dishwasher? I know this one is old since I've lived in my house over ten years and it was there when I moved in.


... Bosch Dishwashers

The dishwasher cycle starts and gets 20-30 minutes in and then stops giving me the - - - like the door was opened, but it was not. If I use extra heated wash, the cycle stops at 63 minutes left. If I use the regular wash cycle, it stops at 43 minutes left. I have to click the resume button to get the dishwasher to complete the wash cycle. This has been happening evey time I use the dishwasher the last 2 weeks. It is Whirlpool dishwasher model GU2700XTSS! and is only 3.5 years old.


Hello,\015\012\015\012Welcome to FixYa.\015\012\015\012I suspect based on your description...\015\012\015\012"stops giving me the - - - like the door was opened, but it was not, I have to click the res ... Whirlpool Dishwashers

Dishwasher I have had above integrated dishwasher which is intermittently tripping the mains fuse. Power is getting to dishwasher and the washing cycles work until a certain point (not the same time) where a loud bang can be heard and the main fuse is tripped. Reset the main fuse and power still gets to the dishwasher and it works again. It has just started to trip the fuse when its not running any cycle (just when power is getting to it). I've checked the fuse on the spur and it looks ok. I hav


Its quite common for the interferance filter to fail on these models its situated in the base of the dishwasher connected to the mains block usually when they fail you can see black dust around it, ... Neff 24 in. S5456 Built-in Dishwasher

Last month i was washing dishes in the dishwasher and if i remember correctly i opened the door to get a knife out of the dry cycle. i remembered shuting the door back and that is about it. this is my daughters dishwasher by the way. i left her house not noticing that the dishwasher ever finished. a week later she asked me if i had a problem with it. i told her no. when she goes to push the start button nothing happens. it doesn't restart its self. we have turned the breaker off and on


Hi.Depending on the model you may need to reset the dishwasher. Most Kenmore and Whirlpool built dishwashers for example need to press a reset button sequence to operate again after a problem has occurred. In that case you usually get lig ... Dishwashers

Frigidaire dishwasher won't end cycle - will run on and on for hours. Sometimes it cycles through, usually it just endlessly washes and rinses. I have to CANCEL the cycle, which causes the dishwasher to empty and run a few RINSE ONLY cycles (which are consistent, cycle time wise) to rinse the soap off of the dishes. Also, the door for the soap seems to stick - how long into the cycle before the soap door should open? Also, does opening the washer during it's cycle (to add more dishes) change or


I would say the resettable thermostat has failed. There is a thermostat which senses the water temperature, and when it fails, it causes the dishwasher to run constant. Replace the thermostat underneath the dishwasher and that should cure problem. P ... Frigidaire 24 in. FDBB540 Built-in Dishwasher

I am getting a clicking/ticking noise (1 click/second) from my Maytag (model MDB9100)dishwasher after it goes through its auto clean normal wash cycle. At the end of the cycle the arrow = clean and the clicking sound is there. I opened the washer door for about 1 minute noted the soap containers are empty, dishes clean, machine still hot/steamy. Closed the washer door and the clicking sound resumes. Please advise.


This is the heated dry timer going through the drying cycle until the dishes are dry. The dry cycle runs on a timer and it will click through the cycle until it finishes the amount of time preset on the timer to dry the dishes. ... Maytag MDB9100A Dishwasher

I have a GE Triton XL Dishwasher. It is about 4 years old. The dishwasher cup is not opening up during the wash cycle, therefore the gel caps are not getting dissolved and dishes aren't being cleaned.


... GE Tritonr XL GSD6260JCC Dishwasher

Dishwasher - Bosche - SHV43A03GB - When the main power switch is ON, even with the door open the pump/motor continues to run (ie. Stop-cycle does not operate). However, the wash-program itself does not run, even with the door closed (ie. No water entering the dishwasher, even though water supply is on and feed lines are clear - not kinked). It is like the program is 'stuck' and I cannot seem to get it to reset.


Your door switch is likely faulty and should be replaced. You can get them at partselect.com ... Dishwashers

Hi, I have an LG LDS4821 dishwasher and it appears to stop working properly. The dishes don't seem to be cleaned at all. It seems like the spray arms are not spraying the dishes as the dishes are still dry/dirty after a normal wash cycle. I did notice that the detergent was used during the wash, and a trail of white residue was at the bottom of the tub. I can hear water pumping into the dishwasher, but when I opened it during a wash cycle, there was a puddle of water at the bottom of the


Hi,\012\012\012\012\012I\012have an older dishwasher also and recently my wife also complained\012about it not cleaning right... so me being the man I am tried in vain\012to clean the things... Bought new ... LG LDS4821 24 in. Built-in Dishwasher

Help! My dishwasher runs thru it's cycles but when I open it I find my second detergent cup still full of soap and my dishes still dirty. I have an older maytag dishwasher but have never had this problem with it. I've tried running a short prewash cycle with the soap despenser open to wash out the soap from the open second despenser but it doesn't wash it out. I know water is coming out of the spray arms but can't see if the arms are spinning although when running it does sound like they ar


Hi,\012There are three common problems that cause the Soap Dispenser or Cup not to open. I have a tip that will explain these problems in detail....Dishwasher Repair Problem ... Dishwashers

I am a licensed plumber who installed a frigidaire fdb1o5rem1 dishwasher for a customer about 2 years ago. It has water to the solenoid valve and the screen is clean. I can see water coming in to the unit on left side through the port hole on the inside of the unit. Dishes do not get clean and it doesnt act like water is being distrubuted inside the dishwasher. Soap never gets washed away from door. Dishwasher makes funny sound in mid cycle like the pump is not running in wash cycle. Discharge p


I can see from what you have described (by the way it is a very clear and precise description which is very helpful), there is a problem in the water circulation system. These dishwashers use an alternating water flow method to split the water circul ... Frigidaire Dishwashers

Item: Whirlpool Ultra Dishwasher Age: 3 yrs Problem: Not enough water to effectively wash the dishes. State: When the dishwasher is started, the fill valve opens as normal. Only about 1/2 the amount of water is let in when the pump turns on and the washing cycle begins. Opening the door shows that the water level does not reach the bottom of the float. When I close the door, the wash cycle begins again but stops after a few seconds. This is when the water begins to fill again. This time, the wat


Larry,The float is generally for overflow conditions and will interrupt power to the fill valve solenoid. If you are not filling completely in the time allowed by the timer, it is most likely a flow restriction in the water ... Whirlpool GU2400XTP Built-in Dishwasher

My dishes have a film and sometimes have mould on them after they've been run through the wash cycle. All my dishes are practically clean when the dishwasher is run and we open the door as soon as the cycle is done. Anyone have any solutions? Is it safe to run an empty wash cycle with bleach instead of dishwasher detergent?


Try using some orange tang drink crystals...sounds odd but works really well.. your dish washer will look like new inside ... Bosch 24 in. SHX33A02 / SHX33A06 Free-standing Dishwasher

Hi, Just moved into a place with a DU4500B Magic Chef. After a cycle there is still a clump of wet soap in the main wash cup dispenser and the dishes aren't clean. Yesterday I tried putting the soap in the pre wash and and main wash dispensers but leaving the main wash soap dispenser OPEN rather than clicking it shut, and there was still left over soap in the dispenser and granulated soap residue on the dishes and they weren't clean. Many thanks for your help.


Hi,\012\012\012\012\012I\012have an older dishwasher also and recently my wife also complained\012about it not cleaning right... so me being the man I am tried in vain\012to clean the things... Bought new ... Magic Chef 24 in. DU4500 Built-in Dishwasher

We have a Sears Ultra Wash III dishwasher, model 665.1677993, bought in October, 1995. It is not filling with enough water to get the dishes clean. I took the water valve out and looked at it and it seems okay. It doesn't look like the valve is opening all the way - just my guess. A small stream of water comes out with good pressure, but it is a small stream. I can't find any screens or filters in the water line coming in. The fill cycle lasts only about a minute. Is that adequate? Steve


There should be another letter after the p in your model number. If it's just a B then there are no parts available for that model. Typically a dishwasher will fill for 90 seconds or more. One minute or less sounds like you have a control board is ... Whirlpool GU2400XTP Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2663 seconds