Having problems with your Maytag Dishwashers ?

Maytag dishwasher, has dead control consul, does have power to the board and the latch swithes are good. is there a way to troubleshoot the touch pad? replace the console or the board, or both? thanks, Bruce


Answers :

The only way possible to see if the touch pads are working is to test the voltage of the control pads when it contacts. The input of the Microprocessor should be checked for the pad control inpulse to come in. If there is no trigger voltage to the mP this can be the control pad problem.
\015\012The mP must be checked for the working voltage and also the frequency oscillation at the crystal leads. If so the mP is working with a suspected control pads which is not able to set the program or timing.
\015\012There is no way but to remove the sticker pad and replace, One difficult way to have a chance is to remove the carbon sticker pads and check continuity , You can use a carbon pen to line the tracks so that the multimeter reads. With this it is possible to have a temporary fix.
Repair Help & Product Troubleshooting for Maytag Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Maytag dishwasher, has dead control consul, does have power to the board and the latch swithes are good. is there a way to troubleshoot the touch pad? replace the console or the board, or both? thanks, Bruce


The only way possible to see if the touch pads are working is to test the voltage of the control pads when it contacts. The input of the Microprocessor should be checked for the pad control inpulse to come in. If there is no trigger voltage to the mP ... Maytag Dishwashers

I have unresponsive touch pad, blinks, but the dishwasher does not come on. do I need to replace the control board? or the touch pad? it's a new machine and we have only used about 10 times since we had it. This is the second dishwasher we have purchased. Could it be there's a power serge burning out the boards? Should DW be on a GCFI outlet?


If it's new(less than a year old) it should be under manufacturers warranty. if not under warranty b4 replacing any parts try killing the breaker for a minute or two ... GE 24 in. GLD5860LSS Stainless Still Built-in Dishwasher

My Maytag Dishwasher MDBH750AWW will not turn on. Pressing the key pad on the top front does not activate the controls. I traced the wiring and found it is active in the door latch assembly, which I recently replaced. Question: 1) If I purchase a new Control Panel exterior white key pad, which is linked to the interior Control Board, should that solve the problem? Or,2) if I purchase a new exterior Control Panel finger touch pad, and an interior Control Board, will that solve the proble


... Dishwashers

Model # KUDSO1DLSS1 Kitchenais dishwasher - had a burnt electric smell coming from the area of the touch pad (not the vent). Did "some" research and decided to replace the control board - smell went away - ran 3-4 cycles over a few days and then - no lights - tried a new control board (thinking the old defective) - nothing - replaced the thermal fuse - nothing - what next????


... KitchenAid 24 in. KUDS25SH Built-in Dishwasher

The touch pad for favorite setting and start don't work. The only way we can make it run is by using delay start. Would like to fix it ourselves if someone can tell us what needs to be replaced. Thanks Sue Andrews [email protected]


Your looking at either the main control board or touchpad. I would say 80% controlboard 20% touchpad. Does the bottom light up when you touch the start button or delay button?James Memije\012Head Technician\012Accufix Applianc ... Frigidaire 24 in. GLD3450RD Built-in Dishwasher

My Frigidaire Dishwasher PLD4375RFC is showing 3 blinking lights at the same time when I flipped the power at the circuit breaker off-on: High Temp Wash, Air Dry on the touch pad and PF on the display. It would not respond to anything that I tried. All blinking lights are off and machine does nothing when I open and close the door. Flipped the circuit breaker off-on again to repeat the sequence. I replaced the controller board, as recommended by the appliance guy since he checked and said ele


... Frigidaire PLD4375RFC Dishwasher

Du1100xtpq7 has had the touch pad replaced along with the circuit board that goes behind it and yet it just keeps repeating the wash cycle and goes for hours


\015\012Hi,\015\012\015\012\015\012\015\012\015\012The basic reason for longer wash cycle is due to more time taken for the temperature to reach the adequate temperature. The sensor keeps going into new cycles till it finds the wate ... Whirlpool 24 in. DU1100XTPS Built-in Dishwasher

Touch pad/control board not working?


PART NUMER 8193762 IS WHAT YOU WANT TO CHECK. YOU CAN SEE THE PICTURE OF THE PART AT REPAIRCLINIC.COM ... KitchenAid 24 in. KUDP01IL - Multiple Color Built-In Dishwasher

After a power surge the dishwasher does not work at all. It just beeps constantly. There are no lights on the touch pad at all. The only thing that stops it from beeping is to remove the 2 pin black and white wires. I replaced the control module. Nothing changes. Do I need to replace the touch pad? What about the 3 digit clock? These parts together cost 145 dollars. I do not want to buy these parts and put them in to find out that did not fix the issue. I also unplugged the


... GE 24 in. Profile PDW9880JSS Built-in Dishwasher

Control board gasket/cover won't attach to replacement console board


... Frigidaire PLD4555RFC Dishwasher

Amana model ADB1500AWW, start/cancel touch pad does not work...power to unit...wash cycles can be selected. Could it possibly be a door switch?..touch pad or circuit board?


... Amana Dishwashers

My Samsung DMT800 series dishwasher has had the main control board replaced under warranty three times since I've had it. The problem: The unit won't activate via the touch buttons until I pull the plug for a second and "re-boot" the device. It then works for a few days or a week and fails again. The last board was replaced two weeks ago and it has failed only once. I'm waiting for it to fail again before I call Sears home services again. Has anyone else had this issue? My repair man has said y


... Samsung Dishwashers

I have a Kenmore Elite Dishwasher Model 665.13773K600. It seems to have no power to the touch pad (top) control panel. I have already checked the circuit breaker and the power to the dishwasher. A friend said that it may perhaps be the thermo fuse cut out that needs to be replaced. 1) Is this true? 2) How can I remove the 1" thick control panel touch pad after removing the six screws- it seems to be stuck, and I don't want to break the plastic touchpad.


... Kenmore Dishwashers

I have a KitchenAid dishwasher model KUDC10IXWH1 that has no control power. I have already verified that there is 120V at the control board. The unit kept the lights on after the cleaning cycle was done and I couldn't shut them off. I reset the electrical breaker and now nothing works, but the board has power. Please give any advice you might have. I was thinking of replacing the board, but I'm not sure if it is the board or the front control panel. Any way to tell?


... KitchenAid 24-in Built-In Dishwasher White ENERGY STAR KUDC10IXWH

Am15 dishwasher problem: The pad will only turn on and off. Can't get it to cycle. Was on cycle 4 needed cycle 1. Got it to cycle 1, but now on and cycle does not work and when I push the off button it reboots to on. I put new pad on thinking it was the pad but same problem. Question: Is there a way to reset the board? should I be looking some where else? I cut the power at the breaker box to see if that might reset with no luck.


... Hobart AM15-2 Dishwasher

Touch pad replacement


... Maytag Dishwashers

I have a Kitchenaid Dishwasher M/N KUDS25SHWHO. Had to replace the control board because the unit would not start. Installed the new board and the unit now operates, but not correctly. Once in awhile on the Normal cycle, it will get a third of the way through the cycle and just stop. Used to be, you could hit any of the Wash Selection buttons and than any of the Options butons and then hit the Start button to begin the cycle. Now, as soon as you hit one of the Wash Selection buttons, the un


... KitchenAid 24 in. KUDS25SH Built-in Dishwasher

Maytag dishwasher, control panel is dead, has power to board,but there are no lights on the panel when you close the door, like it normally would. any ideas I replaced the board with no succes. thanks Bruce, B&L Appliance


I think you have diag your problem . your have power to the board . so the inter lock switches are ok . and no lights . if you look at the printed pc board i think yoy may be able to see that one or more ... Maytag MDB5100A Dishwasher

My Amana ADB1500AWB3 has power all the way to the control board but the panel lights do not illuminate and the dishwasher won't run. I suspect the control board is bad, but I hate to spend the $100+ to replace it only to find out it was something else. Any advice?


... Amana 24 in. ADB1500AW Built-in Dishwasher

I have a Jenn-Air dishwasher model #JDB1100AWW. When I try to start it, the start light won't turn on or the delay light if I try that option and it won't run. I've replaced the control panel/board and still nothing. Is it possible the touch pad needs to be replaced?


... Jenn-Air Dishwashers

KitchenAid KUDP02FRSS1 lights flashing - Replacing control board


... KitchenAid 24 in. KUDP02FR Built-in Dishwasher

Soap dispenser will not open. I replaced the wax motor and still nothing. Is there a way to verify if the control board is bad?


Verify that the bottom tray is not in backwards. There is a space on one side only, usually, and this keeps the door forced shut. ... Whirlpool Dishwashers

I have power to the unit and the door switches or working fine but nothing will work ?? i think it might be the touch pad or the circut board . can you confirm ?


... Maytag MDB8851AWS Stainless Steel 24 in Builtin Dishwasher

Whirlpool Quiet Partner II Model # 575-0 Only two of the cycle lights come on ( light and heavy ) and the start light does not work at all. Needless to say the machine doesn't work. Any ideas? By the way, the mother board has just been replaced


Check the door switch,see if it has continuity threw the switch,when it is closed.Make sure there is 220 volts going to the machine,the breaker box might have two throws for this 220 circuit,and one on them maybe tripped,or off. ... Dishwashers

No water. replaced solenoid for inlet water motor runs but no water flow I think it's the control panel (touch button) is shorted out. Whats the cost of a new board.


You might have to call up GE service support to confirm. check this link:\012\012www.geappliances.com \012\012check also for spares, post your queries: ... GE 24 in. GLD5560LSS Stainless Steel Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0649 seconds