Having problems with your Maytag Dishwashers ?

The power is on the machine but when the start button is pushed the light does not come on and none of the cycle will start.


Answers :

Most common cause is a faulty door switch that will not let the machine operate. There is also a thermal fuse in the back beehind the rear panel that can blow and allow some power but not enough to operate the machine.
Repair Help & Product Troubleshooting for Maytag Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Our AEG Favorit 50620 dishwasher won't start. When I push the power button, the power light comes on, but none of the other lights. Pushing the function buttons has no effect. The door is fully closed, and it was working perfectly before. I have tried turning it off and on, unplugging it etc. Nothing works. Interestingly, if you push more than one function button at the same time, some of the function lights come on, but then when you try to start the cycle it still won't work. Help!


... AEG 24 in. Favorit 40650 Free-Standing Dishwasher

The touchpad buttons no longer work to select a wash cycle. When I push "Start" the light above "Smart Wash" comes on and the dishwasher operates normally, but I cannot select any other cycles and the light only comes on after pressing "Start", not before. Also, the Options buttons seem to work normally but the delay button doesn't scroll through 2-4-6, it only toggles the light on and off above "4". The item is 15 months old. Thank you.


... Kenmore 13743 Staimless Steel Built-in Dishwasher

When i push the start button,it doesn't light up and start. The normal cycle and the other cycles lights work but it won't start. If i push hi-temp wash and heated dry several times, all lights will come on but when i try to run it through a cycle, it won't start.


I would replace the key pad it sounds like since everything else works.. so you hit the normal wash and start the dishwasher sits there for a min or two and turns off.. Its not recognising the start button ... Dishwashers

The power is on the machine but when the start button is pushed the light does not come on and none of the cycle will start.


Most common cause is a faulty door switch that will not let the machine operate. There is also a thermal fuse in the back beehind the rear panel that can blow and allow some power but not enough to operate the machine. ... Maytag Dishwashers

I have a Frigidaire FDB956rbc0 model. When the start/cancel button is pushed nothing happens. There is power and other buttons cause lights above what is pressed come on. Delay wash works but when it starts the washing light flashes. I have run a test on the cycles by pushing start/cancel and power dry button during power failure mode. all cycle run properly. Any thoughts?


... Frigidaire Dishwashers

My Frigidaire Dishwasher FDB1050RES2 gets stuck in a rinse cycle. The light on the front will be lit "clean" but the bottom of the washer is full of water. Opening the door does not turn off the "clean" light. For me to get it to run, I have to unplug it, plug it back in, push the start button until the ?washing? light comes on. I then push the start button once more and the dishwasher will begin to drain. I open the door as soon as I hear the water stop draining into the sink drain. This


By the descrition you are giving you will need to replace the main control board.Part number 154568401.you may also need to check the float switch.The part will run about 110.00 dollars from a local parts store ... Frigidaire 24 in. FDB1050RE Built-in Dishwasher

Dishwasher wont let u select a cycle...all buttons seem locked...ive unplugged it for 5 seconds or so and then plugged it back in and the normal wash button light comes on and the heated dry button light comes on, but it wont start and it doesnt respond when buttons are pushed...please help. thanks


... GE GLD4560NSS Stainless Steel Built-in Dishwasher

I have the above dishwasher shv57c03uc just less than 5 years old. The door latch does not engage solidly. when i pust start button left side lights on indicator right does not come on and i have to push on button twice for washer to come on. When it does come on the cycle is real short and it does not complete a full cycle. I an asuming the circuit board is defective!! does this sound right? if so how can i replace the board?where can i get troubleshoooting instructions?


Hi\015\012\015\012You are right it is the ... Bosch 24 in. SHV57C03UC Built-in Dishwasher

My dishwasher won't start when push the button , you can't put it in normal cycle and the a very faint light comes on the start but it won't start, lights stay on cycle and then go off. Any suggestions


... Maytag Dishwashers

After selecting wash cycle,I push start button. washing light comes on for a second then goes off.start light keeps on blinking. washing cycle would not start.


Check flood switch float is on(the float under the bottom rack)...also the switch under that...also you ca use a 110 volt test cord to test the inlet valve ... Dishwashers

Frigidaire Dishwasher Hi, I have installed a new model GLD2250RDC0 Frigidaire dishwasher and it will not start. Power and water supply is connected. When I push the cycle button for Normal the light comes on but when I push Start nothing happens except the "hi-temp wash" and "no heat dry" lights flash. I assume this is some kind of troubleshooting code but the manual does not cover this and I am in Honduras so service is non existent. Any ideas? By the way, I was a builder in the States for 25 y


... Frigidaire 24 in. GLD2162RDC Stainless Steel Built-in Dishwasher

I used the "rinse only" cycle on the dishwasher a little while ago. I've never used this cycle before. After dinner I tried to start the dishwasher, but no other buttons on the panel respond except the last one I used, which is the rinse only cycle. I push and push, I tried pushing and holding, nothing works, I get no lights no anything. I've been using the "light wash" cycle for a long time and I normally just push the start button and the last cycle used starts automatically, so I wasn't a


Try un-plugging the dishwasher (check for cord under the sink) or turn off the breaker to it to re-set the control board. If this does not resolve your issue you may have a defective key panel. ... Dishwashers

I have model GU3600XTSY2. Sometimes the pots and pans light flashes for no reason. Sometimes I can push that button and it stops. However, the cycle I select to wash the dishes is constantly interupted by the pots and pans (P&P) light flashing. If I push the P&P button, the wash cycle usually starts where it left off. Sometimes it will go back to the beginning of the cycle and begin all over again and get caught in a loop; start washer, P&P flashes, push P&P, begins cycle from beginning, P&


... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

I have a Kenmore Elite Dishwasher Model 665.172824000. We think it stopped part way throught the dry cycle. The green "Clean" light has been flashing since in 7 flash cycles non stop. I tried pushing the Cancel button, it starts the drain pump then stops and we are back to where we started. I tried to start a new wash cycle but when I close the door and push the start button it just give 3 quick red flashes and then nothing but the green clean light flashing again. I shut the breaker off fo


So sorry but the partsdirect site for sears locked down my computer. Check where the drain hose connects to your pump and see if there is a small device the hose connects to that has 2 wires going to it. If it does unplug the wires, turn power off, w ... Dishwashers

GE triton xl dishwasher has power but will start a cycle. Lights come on when buttons are pushed. When you push start it makes a locking sound but does nothing. I've tried restarting by turning power off for 30 seconds to a minute and still does not help.


... Dishwashers

Cranky dishwasher I have to admit my wife's solution is the only one that works. Our ten-year-old Superba built-in usually starts a normal cycle part-way through, at the wash part, without filling or opening the dispenser door. Therefore the dishes come out with the soil now baked on. Closing the door, selecting normal and start results in a pump-out sound, or at least just the pump running to wash the dishes. The dishwasher ignores any cancel button push,and the light does not come on over t


You want to make sure that the dishwasher is level and secure first of all. Then I would look into the door latch assy. Sounds to me that you are not making all the latch switches when closing normally. When you are slamming it, you are making the s ... KitchenAid KUDS24SE Built-in Dishwasher

Will not start , all lights will come on but will not start when i push button. I have done the series of pushing scrub/dry and it will run through the series of cycles.


Check the motor start capacitor on the side of the motor,it may be bad and w/o it the motor wont start or run ... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

Matag MDBH940AWS dishwasher: Push start and light comes on but dw doesn't start - push again and light goes out but pump starts running but no water enters, push again , it shuts off ;; past problem never addresses is delay feature stopped working , no lights come on when delay buttons are pushed, so... control head in door replacement in order? Thanks , [email protected]


... Maytag 24 in. MDBH940AWS Built-in Dishwasher

Hi there. I'm having problems with my dishwasher. Usuaully once loaded, i push the start button, the closest green light to the start button flashes and dishwasher fills/cycle begins. Now, when i push the start button, the furthest green light from the start button flashes, you can hear the motor running but no cycle begins. No water fills the dishwasher.


... Hotpoint 23 in. BFV62 Built-in Dishwasher

I have a Whirlpool Gu180 ESJQ with a blinking green start light. If I clear this light (hold the start button for 5 second to place it in the end of cycle) then I can get it to start another wash cycle. However, the next wash cycle ends with a blinking start button again and the dishes aren't dry. I had an appliance service man come to check it out and he could not detect any problem! Now I have a leak!


... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

Mdb7809awb2 will not start. cycle lights come on but no response when start button is pushed


... Maytag Dishwashers

The scrub light is the only light that comes on. i push all the buttons on the control panel of the dishwsher,and front panel, but it still will not start any wash cycles. The dish washer was working fine until now.


Thanks for your question!I'm sorry that you haven't received an answer yet.The response rate on FixYa FREE questions is usually over 80%, but sometimes questions go un-answered when:1. the question is unclear, incomplete, or poorly ... Maytag MDBH975AWS Stainless Steel Dishwasher

Non-starting unit The dishwasher will not start, reacting as if the door is not closed. The right side of the control panel (air dry, sani rinse, hi-temp scrub) allow selection i.e. the indicator light comes on. However, none of the cycle selection buttons on the left will engage.


... Kenmore 24 in. 16934 Built-in Dishwasher

I have a KitchenAid KUDS02SR dishwasher. If I push any buttons on the control panel the Normal light starts flashing rapidly and will not stop no matter what I do. While this is happening it will not start a cycle. If I turn off the power the light will stop flashing, but when I push any other button the Normal light starts flashing again.


The touch panel may have a bad push pad and will not let it probram there is a tech sheet under the dw just behind the toe panel this wil help you understand the flashing code . it will tell you what is wrong . but a ... KitchenAid 24 in. KUDS02SR Built-in Dishwasher

Maytag dishwasher mdb7601 will not run- light doesn't come on and nothing happens when you push the buttons. Earlier it would work but if you pushed the light cycle button the longer cycle would light up and it would run. Then the time running light did not light up.


... Maytag MDB7100AWB Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1885 seconds