Having problems with your Maytag Dishwashers ?

I have a 1 year old maytag dishwasher and it has the touch buttons on top of the door . When you touch the buttons to turn it on, nothing happens. It will light up the type of wash you want e.g. heavy,light...., but it won't start when pressed. It will cancel when pushed, but can't get it to start. HELP!!!


Answers :

Repair Help & Product Troubleshooting for Maytag Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a 1 year old maytag dishwasher and it has the touch buttons on top of the door . When you touch the buttons to turn it on, nothing happens. It will light up the type of wash you want e.g. heavy,light...., but it won't start when pressed. It will cancel when pushed, but can't get it to start. HELP!!!


... Maytag Dishwashers

I can't get my electrolux dishwasher to run. It seems as though the touch pad is not responsive. It says to reset holding down the sanitize button, I do that it beeps but doesn't do anythng. All of the buttons are not lit up. I have to hold the delay start button along with the sanitize button to light the buttons up, still the buttons don't seem to be responsive, I touch the start and the lights go away and flashing numbers appear. Et 19 66 02 34 Any help would be appreciated.


... Electrolux EIDW6405HT Builtin Dishwasher

My kitchen aid dishwasher will not start I replaced the interface control board thinking that was the obvious problem. When you go to set the dishwasher to start some of the settings don't always light up then when you push the start button the lights will flash then start but it's not flashing and won't start. I get lucky once in a while and get it to flash then start. I don't know where else to look. I don't want to start replacing parts one at a time till I get lucky. My model # is KUDIO1F


Check all cables especially the ribbon cables from the user interface to the electronic control assembly as steam from dishwashings will create small amounts of corrosion and inhibit signals to and from these 2 components,unplug each,inspect,and reco ... KitchenAid Dishwashers

Kenmore undercounter dishwasher model 66517019400 wont start..I want to purchase a new control board do you think this is the problem? normal cycle light comes on, cancel button works, heat on button works, just wont start ??


It might not start because the water solenoid is failed, or the water level sensor is failed.\015\012\015\012You have to use a meter to test these components first. Put your voltmeter on the two leads going to the water solenoid, and psuh ... Kenmore Dishwashers

I have a Kitchen Aid dishwasher Model KUD1021RWH1 that is malfunctioning. The display has the Heavy Duty, Normal and Cancel lights all flashing on and off at the same time. This problem has been intermitent. The happens after we fill the washer and want it to start. I push the Normal button and the heavy duty button flashes with the normal button and the dishwasher wont start. So, I push the cancel button and it flashes also.The washer has been cycling fine since we bought it a few years ago unt


... KitchenAid 24 in. KUDI02IR Built-in Dishwasher

I have a 4 year old Maytag MDBH945AWW and the panel lights come on and I can select cycles... but the dishwasher wont start. I tried holding the start cancel button, tried turning the breaker off for a couple of hours, took the inner panel off the door and checked the latch, but its still wont start. Any other suggestions? If it needs a new control panel its probably better to just get a new similar dishwasher for $300, correct?


What you need to do is read for continuity and power across the door latch switch. (2 white wires) AND 2 Black wires Both wires must read continuty at the control panel connectors to the power source terminals for the unit to start. Since the co ... Maytag MDBH945AWW / MDBH945AWQ / MDBH945AWB Built-in Dishwasher

IDL700 wont start Kept getting error message to say there was a blockage. Checked all the pipes and pump, all fine. Now the blockage lights are out, but the machine wont start at all, just beeps when I press the start button, then nothing


Sorry to read about your problem, I hope this helps you out.the blockage, maybe inside the pump of the unit, or at the check valve.I suggest you contact a service company..I tried to help you. Please help me and Ra ... Indesit 24 in. IDL700 Built-In Dishwasher

How do I get my Bosch SHE4AM16UC dishwasher to pause and then start again at the same place it was in the cycle? I pushed the STOP button and then the START button and it started at step one. My dishes will be super clean, but all I wanted to do was pause it for a few minutes.


... Bosch SHE4AM16UC 24 in. Built-in Dishwasher

I wanted to heat up a cup of tea. As I've done many times before, I pressed Time, then 1:20 seconds, then I pressed Auto Start, but fear I may have touched the button below it, which says Start in small red print. The oven wouldn't switch on, and I noticed a small green u-shaped mark had appeared at the base of the 1: I pressed Clear, and repeated my movements, making sure this time that I pressed Auto Start. Again, nothing happened. I've cleared the touchpad several times, but the oven won't


... Danby 22 in. DDW399 Free-standing Dishwasher

We have started experiencing a problem with our Kenmore Elite 655.15982 dishwasher. Each time we close the door, NoHeatDry lid would go on immediately. It would stay as is of would go flashing. If you touch any button, LockOn lid would go on. Then no other buttons would respond. And often both NoHeatDry and LockOn indicators would be flashing... We tried turning machine for an extended time on the fuse, etc. At times it would work for some time and then cycle get stuck again at the same p


These errors are due to a faulty control board and needs to be replaced. If its still underranty get it fixed before it expires as it is a costly repair to replace. ... Dishwashers

When I try to start the dishwasher, I can get the light to show I want it do do a normal load. Then when I hit the start button, it lights up but the machine will not sstart. Then in a few minutes the lights on the control panel at the top of the door go out. What can I do to fix this? The model # is KUDS011JBS0 tHE 0'S HAVE A SLASH ACROSS THEM THE TYPE IS 577-0 SUPERBA


Hi,\015\012\015\012Your control board has gone bad... you will need to replace it.\015\012The replacement is not very hard, just make sure that you mark where all of the wires go before removing them.\015\012\015\012Here ... KitchenAid Dishwashers

The dishwasher wont start. Light comes on for every button except they don't flash when I want to start.


It is likely the control panel is faulty or the door switch is not making contact when you shut the door.\015\012\015\012Check ... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

ASKO dishwasher D3122 drain pump wont stop pumping and the machine wont respond when we press any of the program or start/stop buttons. the program light is flashing. We can turn the power off with the main switch on top of the door but when turning it back on the pump starts pumping again. please tell me how to fix this problem so we can get it up and running again.


... Asko D3122XLSS Stainless Steel Dishwasher

Unit will not start after pushing the selectin buttons and makes a clicking sound. Also it kicks the switch panel rocker off; and you can get an electrical shock from touching the unit.


I bought a new dishwasher and got rid of this LEMON. And the new one is NOT A KITCHENAID! ... KitchenAid KUDS24SE Built-in Dishwasher

I have a model pld4375rfc3 that want start. Wont do anything when you mash the buttons, the rinse Only light is on. tried the jumper from black to black and white to white for the door switch but/ Dishwasher now has a code dc flashing, also it does not have a heated dry


... Frigidaire Dishwashers

Prima lpr601 problem- filled dishwasher up sa normal set the wash pressed button on far right (dont know what it is but needs to be done), closed door and loud raattling so i opened door to make sure all spray arms were clear which they were, closed the door , again the rattling . now the green light has gone out on far right and cant get it back on so program wont start at all. Any advice?? please help


... Dishwashers

Start button not working...can't get machine to start


The micro switch is bad. I had the same problem cleaned the switch a few time (nd bought some time) but in the end I moved a switch from a cycle we did not use to the start position. Cost was nothing but my time (must have skills in soldering PCB ... KitchenAid 24 in. KUDS01FLBL Built-in Dishwasher

Lights work, dishwasher works but "start" button won't start it. I can get it to work sometimes by hitting a few of the buttons back and forth. Otherwise, I can't get it to start.


... GE 24 in. Monogram ZBD6880KSS Stainless Steel Built-in Dishwasher

I HAVE A NEW CRAFTSMAN PRESSURE WASHER WITH KEY START. I HAVE USED IT ONCE AND WHEN I TRIED TO START IT IT WAS HARD TO START HAD TO PULL START IT. NOW IT WONT START. LET PRESSURE OUT HAVE HOSE OH AND RUNNING, NEW SPARK PLUG HAS OIL, GAS FILTER FINE.HAS GOOD COMPRESSION, BUT WILL NOT FIRE GET SOME RECOIL. GETTING GAS TO SPARK PLUG AND GETTING SPARK. IM LOST PLEASE HELP.


... Pressure Washers

Hi, We have a Smeg ST 663 dishwasher that does work. However, sometimes when you want to use it and turn the power button on it beeps twice with the red light flashing and you can't get it to work or change the settings. Sometimes if we leave it for a while and try it again later it will work, but it is annoying as sometimes it won't want to work for ages and we really want our dishes cleaned! The dishwasher doesn't have many buttons on it (a power button, cycle selection button and 1/2 load


Hi,\015\012\015\012Turn machine on and press and hold the programme select button till the light goes out about 5-7 seconds see if this resets it if it does start a cycle and see what happens.Otherwise the pcb as its not responding to an ... Smeg Dishwashers

My Frigidaire Dishwasher FDB1050RES2 gets stuck in a rinse cycle. The light on the front will be lit "clean" but the bottom of the washer is full of water. Opening the door does not turn off the "clean" light. For me to get it to run, I have to unplug it, plug it back in, push the start button until the ?washing? light comes on. I then push the start button once more and the dishwasher will begin to drain. I open the door as soon as I hear the water stop draining into the sink drain. This


By the descrition you are giving you will need to replace the main control board.Part number 154568401.you may also need to check the float switch.The part will run about 110.00 dollars from a local parts store ... Frigidaire 24 in. FDB1050RE Built-in Dishwasher

Model # KUDP01FLSS5 Dishwasher has power. Normal button lights up but start button wont light and wont start dishwasher


Please check the internal connections. ... KitchenAid 34 in. KUDP01FLSS Stainless Steel Built-in Dishwasher

Whirlpool adp 5550 Dishwasher wont complete a cycle. The light in the start button flashes four times in a continuous pattern. Have pressed the start button for 3 -5 seconds to reset after which the machine seems to operate ok then it stops and the start button returns to flashing. Have cleaned the filter and checked the sullage pipe for blockages What do I do next?


... Dishwashers

Hi. Got a dishwasher from IKEA - Whirlpool DWH B00. It wont run anymore, 2 years old. It just wont start up, it starts to give a beep, and the solution is to press the <|> button for 2 sec, then restart it. But it still wont start. I've cleaned all filters, checked for water on board underneath, and given it some salt - no luck. Any ideas?


... Whirlpool Dishwashers

My KitchenAid KUDS01FLSS0 won't turn on when the "Start" button is pushed. Several months ago it began requiring multiple pushes to get it to start. All the cycle lights on the control panel work when pushed - except the "Start" button. Online & repair parts person suggested I replace the: - Tail Cable Ribbon; did not fix problem, then - - Electronic Control Board (interface) which also did not fix it. Should I replace the Electronic Control Board that is actually the part with the buttons


... KitchenAid Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1142 seconds