Having problems with your Maytag Dishwashers ?

Hello...my Maytag dishwasher seems to be stuck on heat water setting....when I set it to start the way I always have, it doesn't fill with water, but just sits there heating up the interior without any water being drained or flowing in. Any ideas? Thanks! Scott Chandler


Answers :

Hi
\015\012\015\012


\015\012Thanks for using FixYa.
If the cycle doesn't complete, then the first thing\015\012that should be checked is the Timer and then the heating element. Timers\015\012don't often fail. But if every other part of the dishwasher seems to be working\015\012properly and the timer knob seems to be stuck in one place--doing one function\015\012continuously--the timer may be at fault. Dishwasher timers can't be repaired.\015\012If yours is defective, replace it. Please accept the solution if\015\012the issue is resolved or post a comment for further assistance.
\015\012
\015\012Thanks

\015\012\015\012

Rylee

Repair Help & Product Troubleshooting for Maytag Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Hello...my Maytag dishwasher seems to be stuck on heat water setting....when I set it to start the way I always have, it doesn't fill with water, but just sits there heating up the interior without any water being drained or flowing in. Any ideas? Thanks! Scott Chandler


Hi\015\012\015\012\015\012Thanks for using FixYa. If the cycle doesn't complete, then the first thing\015\012that should be checked is the Timer and then the heating element. Timers\015\012don't often ... Maytag Dishwashers

I have the GE Quiet Power 3 Model gld4400n10bb. When I start a wash I can hear it fill with water (to about 1/2 inch below the heating element). It then waits for about 5-7 minutes and pumps the water out. It fills again several times and pumps out. It doesn't sound like it is washing though. The whole interior of the dishwasher is covered with dried soap. I can also tell that water is not spraying around the whole interior. Any ideas?


... GE GLD4400NWW / GLD4400NBB / GLD4400NCC Dishwasher

Waterintake stops after approx. 35 sec.waterlevel is to low,detergent compartement will not open because of low waterlevel and also water will not heat, because heating element is not covered with water. If I put water in by hand to get the waterlevel above heatingelement everything is fine. Dishwasher has been working without any problems till approx. 18 mths ago. Have also adjusted waterintake time as described in manual by taking off dial knob and adjusted with small flat skrewdriver, but not


The machine fills by time only as you have already determined. The intake screen on the water valve is probably plugged up and cleaning it should solve your problem. You will have to turn off the supply to the dishwasher and disconnect the water feed ... Dishwashers

Dishwasher repair Dear Guru, I hope you are well this evening. I have a Whirlpool Quietwash Plus dishwasher (940 Series) that will randomly have water sitting in after running through a washing cycle. In addition, some mornings there will randomly be a couple inches of water sitting in the bottom without every running the washer. Need assistance. Any help will be appreciated. Thank you for your time. J


Without model unablr to look up exact unit, but in genreral, either ther is a blockage/clog in oyour drain line not alowing complete drain of cycle, as far as never really washing, i would look into perhaps a faulty/ sloppy door switch assembly. if f ... Dishwashers

The dishwasher starts and initially rinses the dishes without heated water. In the next part of the cycle, the water is supposed to heat to a certain temperature.Beginning this morning, in this second part of the cycle,the dishwasher trips the circuit breaker. If you reset the breaker and turn the sihwasher back on, the breaker trips again. What is wrong and how do I fix it?


Hi\015\012\015\012The issue is with the heating element of your dishwasher, it is withdrawing very large amount of power and thus, the circuit gets overloaded and circuit breaker trips. You'll need to check for any short circuits around t ... Dishwashers

Dishwasher Water is not going through upper and lower spray arms. Checked overfill protector switch, inlet valve, inlet valve screen, pump blades move freely, Pumb motor is working , Water enters into machine but does not go throught spray arms. Water heats up, Machine will go through all cycles but without water going through spray arms. 650 / 690 series gldb656jso


... Dishwashers

I can not get the water to drain during a normal wash cyclr. When I press the start/restart button twice it makes noise but no water comes out the end of the drain hose. I have put a shop vac on the end of the hose and can get water out that way but it appears not to be pumping. The washer sits for up to 6 months at a time without being used. Thanks for any help Ted Berry Placencia, Belize Central America


Teddy,\015\012\015\012Buy a new one...then go fishin!\015\012\015\012Richard Vantine (ret'd Colonel...USAF) \015\012Bingelrade, The Netherlands ... GE GSD5310D Dishwasher

Upon selecting a wash cycle and closing the door the machine starts normally (heating water stage) but never clicks to allow water in and wash the dishes. Fails to advance to the wash cycle and just runs without doing dishes. There was water in the bottom after the last wash, filters are clean?


... Bosch SHV46C03 Built-in Dishwasher

"Sensing" Light Moved a 5 year old dishwasher that was functioning just fine to a different location. Hooked everything up and gave it a test run without any dishes in it. Fills and heats water properly, then buzzing noise heard for a ling time and then it drains the water out, with out circulating the water into the washer arms, etc. Any guesses? Could something have gotten lodged in the pump during transport?


There is a relay on the soap dispenser, if it is a Kenmore quietguard 4, I had the same type of noise, the repairman replaced the dispenser, which to me made no sense, because the relay is activated from the control board. After the $130. for the soa ... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

Dishwasher hums as if it is starting to run but no water is coming into dishwasher. The interior is heating up as the heating coils heat up.


Sounds like the solenoid isn't working. Either that or the pressure switch is telling the solenoid that it has water, a regular problem in hardwater areas. This can be temporarily fixed by removing the pink plastic pipe which is connected to the sole ... Dishwashers

No heat up of water or any temperature raise . Dryning not in functing either . Heating element without voltage supply, during normal sequence of operation. Has found relay Eberle with part no T-nr 3940620 in investigation of electrical loop. Please come up with a possible malfunction . Thank you very much Best regards Erik Rasmussen


... Miele 24 in. G665 Built-in Dishwasher

FDW60 dishwasher - taken apart pump and that is clear. Seems that dishwasher fills, and empties and heats all OK but water wont go around the machine ie the motor pump doesnt start - any idea how to take this out and replace without having engineer around? Taken small pump apart and its clear. First of all the Eco and fast light flashed, then we took it apart with some direction from online discussion advice. Now Eco and Pre wash lights are flashing. Machine empties water, then fills with


... Hotpoint 24 in. FDW60 Free-standing Dishwasher

Our Kitchenaide KUDT03FTSS2 dishwasher is not cleaning the dishes like it did when it was new. It doesn't appear to dry the interior and leaves gunk inside, and is noisier than it was when we purchased about 3 years ago. It does not appear to be heating the water - we put a thermometer in there and it read 118. The water out of our tap is hotter than that. The rinse aid has been filled regularly. What should we look for?


Hi, \012I have an older dishwasher also and recently mywife also complained about it not cleaning right... so me being the man I amtried in vain to clean the things... Bought new spray arms online and installedthem in minutes...now the thing works li ... KitchenAid Architect® KUDT03FT 24 in Builtin Dishwasher

Frigidaire FDB1502RGC0 dishwasher set for normal wash and heat dry option, both leds are on. dishwasher cycles through wash, but never makes it to dry cycle. After wash, the leds for OPTIONS high temp wash and dry cycle start blinking and do not stop blinking until I hit cancel - which cancels everything. Open unit and water sitting in bottom. Is it a bad operator panel? Water pump did seem to be working during wash cycle. NEED HELP.


... Frigidaire 24 in. FDBB540 Built-in Dishwasher

The water isn't heating and the dry cycle just goes on forever without drying. We have also noticed that the dishes haven't been coming out very clean. Is this the heating element? Or is there an easier fix?


HelloYour heating element in thee dishwasher is faulty and you should have it replaced,a replacement part should cost you about $50. ... Ariston Technologies L63SNA Stainless Steel Built-in Dishwasher

Kenmore Ultra Wash Quiet Guard - will not drain at end of cycle. After cycle is complete, water (not clean) sits at the bottom of the washer but I still unload the dishes and then turn the cycle dial around again - going past all the water heating and filling and washing - and land on the drain cycle, it will drain. Any ideas why it will not drain when I let a cycle run, but will drain once I cycle it through to the drain option?


... Frigidaire 24 in. PLD2850 Built-in Dishwasher

Small Burn spots on interior tub below heating element. These spots have small cracks in center of them, and leak right through the bottom of the tub, dripping water all over under the dishwasher. Nothing has falling into the bottom of the tub, and nothing has touched the heating element. What in the world could be causing this to happen? Kenmore Ultra Wash Quiet Guard 4 Mod.# 665.1603* Purchased new from Sears 2006


Hi,\015\012\015\012The heat from the element when the dishwasher is in the "drying" mode has caused the bottom to stress crack and become open so it leaks...\015\012Ultimately this will cause you to have to replace the dishwasher... ... Kenmore Dishwashers

Dishlex DX302SB Dishwasher water not heating, have changed the heating element without any success.


Who posted this comment I am really appreciative. I have had the same problem with my dishlex. I disassembled the plumbing and removed a chunk of plastic wrapping from inside the pump. Then I checked the heater with a multimeter. It ... Dishwashers

Our dishwasher goes through the cycle and finishes fine without water in the bottom. Then within a couple hours, water comes up and sits at the bottom of the dishwasher. Handyman could not figure out why. No clog in place.


Hello Sandra, Welcome to Fixya ! You've come to the right place. The problem you're experiencing sounds like (unfortunately) a common one. The water inlet valve has been an issue with B/S/H built ( this includes bosch, thermador, seimens & gaggenau ) ... Siemens 24 in. SE25A266 ExtraKlasse Free-standing Dishwasher

Kenmore dishwasher not draining 587.16193401(model number) water sit in the interior of dishwasher


One possible problem might be that the drain motor is stuck. This happens quite easily if an object is sucked through and gets wedged in the blades of the motor. Many of these motors just stop working until the blockage is removed. You will have to l ... Dishwashers

I have a Bosch SHU53513UC/U12 dishwasher. My initial problem is that the washer smells bad after a cycle and I've noticed some water sitting in the bottom of the unit. After running a diagnostic test, it results in a "2" heating fault. I followed your advice and used a current coil to and attached it to the GYBK-a1-3 hot wire on the control board. After running the test again, it only gets as high as 1.15A and manual says it should reach 11A. What should I do next?


Hello,Welcome to FixYa. ... Dishwashers

Good Afternoon We have a Kleenmaid DW8 dishwasher. At the beginning of the cycle, it will pump out the water, sit idle for a short time and then show the end light, without washing or any further action. A technician came to visit and had a brief look. A follow up call came from his company stating that the circuit board had a crack in it. It would require a new circuit board ($650), the dishwasher to be taken to the workshop and repaired ($150). Upon further investigation, the circuit board had


... Dishwashers

Turns on fills with water but does not wash/run. Will stay on and sit idle, even the heat dryer will work. But the unit will not wash.


... Kenmore 24 in. 17033 Built-in Dishwasher

Our dishwasher Bauknecht GSF 5481 stops washing shortly after start, without heating water. The light for washing program does not light.


... Dishwashers

Zanussi dishwasher washer will go through the wash without heating water ,hence no drying of dishes. not sure of model


Zanussi dishwasher may have a faulty heating element (wire in bottom of wash tub) check for videos to test. ... Zanussi ZT485 Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1257 seconds