Having problems with your Maytag Dishwashers ?

Can not find model number of my Maytag quiet series 100 dishwasher. It has a defective control board that has a bank of burnt resistors. Please help


Answers :

Repair Help & Product Troubleshooting for Maytag Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Can not find model number of my Maytag quiet series 100 dishwasher. It has a defective control board that has a bank of burnt resistors. Please help


... Maytag Dishwashers

Model # KUDSO1DLSS1 Kitchenais dishwasher - had a burnt electric smell coming from the area of the touch pad (not the vent). Did "some" research and decided to replace the control board - smell went away - ran 3-4 cycles over a few days and then - no lights - tried a new control board (thinking the old defective) - nothing - replaced the thermal fuse - nothing - what next????


... KitchenAid 24 in. KUDS25SH Built-in Dishwasher

I have a Maytag dishwasher MDBM601AWW. The control lock on the control pad will not unlock. I replaced the electronic control board and it worked for one wash. Control lock engaged again. I shut down the power and pressed the control lock for 3 seconds as directed by the owners manual. No luck. Please help Rich.


You have to power the unit back up and then holld the lock in for three seconds, if ths does not reset it then the console not the control bord needs to be replaced it comes with a new touch pad ... Dishwashers

Helloo! Dishwasher candy futura cdf 312A not work. On button 50 and 1/2 at the same time flashes controls light. I hear drain pump how to boot. When I turn dishwasher off-on defect not disappears. Please help me.. Thanks


... Dishwashers

I have a KitchenAid Dishwasher KUDIO1iLBS2 and none of the lights come on and if I press any of the buttons nothing happens. The unit is getting power to it as I shocked myself. I did ordered and replaced the control board and still nothing is happening. Any suggestions or ideas? Is there a reset button or is there a possible fuse that is out that would make the lights not come on? Please help.


... KitchenAid Dishwashers

I have a KitchenAid dishwasher model KUDC10IXWH1 that has no control power. I have already verified that there is 120V at the control board. The unit kept the lights on after the cleaning cycle was done and I couldn't shut them off. I reset the electrical breaker and now nothing works, but the board has power. Please give any advice you might have. I was thinking of replacing the board, but I'm not sure if it is the board or the front control panel. Any way to tell?


... KitchenAid 24-in Built-In Dishwasher White ENERGY STAR KUDC10IXWH

Control Panel won't let me hit the start button. The dishwasher is a little over a year old and is used at most once a week. The blue light on the bottom right of the dishwasher seems to no longer light up. The control panel will let me select the wash, but the start button and time indicator does not light up. Not sure if this a real defect and if just a simple exchange of the front control panel will fix the problem? Already tried resetting the circuit breaker and that did not help. Than


... Dacor Epicure ED24 Stainless Steel Builtin Dishwasher

Bosch SHU43C Dishwasher. Where to get parts - quick? Needs a new control-board / circuit board. All valves, switches, heater appear to work. Won't run open the water inlet valve. Won't run the self-check program. Has a burnt connection on the control 'mother-board'.


1-800-944-2904 That is Bosch Company. They will send out-- next day. ... Bosch 24 in. SHU43 Built-in Dishwasher

Bosch dishwasher Does not heat up in the washing cycle and does not drain down at the end of the cycle. End of cycle the display sticks at 1 and the drain pump operates until the machine is switched off or reset. Followed the suggestion in another thread to look for a burnt solder joint on the control board. Unfortunately my machine is a later model than the board shown and has no poor joints on the board. It would seem from previous answers that the problem is either the controller, the heating


1) The water must be preheating by heating elements and thermostat see how to do it.\015\0122) Timer , test for defective,clean the contact, repair wires for loose, broken, or burn.\015\012\015\012God bless you.\015\012 ... Dishwashers

I have a whirlpool quiet partner i dishwasher (model DU1055XTSQ2) that has suddenly stopped working. Control panel has partial functionality. All of the buttons on the control panel have a green LED feedback light when depressed. None of them provide LED feedback anymore except the Hi-Temp Wash, Sani-Rinse, and Heated Dry buttons. So there is power to the dishwasher. Any ideas? Please help Scott


The control board has failed.CLICK HERE to see the parts breakdown. ... Whirlpool DU1055XTSQ Built-in Dishwasher

I need to replace the heating element and electronic control board on my Kitchenaid KUDS01DL Dishwasher. I have the parts. I have been able to find directions on how to replace the heating element, but am not finding anything on the electronic control board. I don't even know where this part goes. I am guessing somewhere in the door, but can't find any instructions. Help...


... KitchenAid 24 in. KUDS01DLSS Built-in Dishwasher

Lights are on, but dishwasher will not start. Called a local repairman. He decided the control board failed. he ordered a new board and replaced it. Now he says the new board is defective. I think otherwise


That model has an electronic thermal fuse that clips onto the control board housing. the dishwasher will not start if that fuse is blown. you can check it if you have a meter. If it has continuity through it, its good, if no continuity, replace it. T ... KitchenAid 24 in. KUDU02FR Built-in Dishwasher

Judging from the information on this forum and others, we think we need to replace the control module on our Bosch dishwasher (she45m05uc/50). The general consensus seems to be that the module has an underrated relay and will burn out again. Has the board been redesigned? Is there a newer board that would work in our model? Bosch says that only part number 676962 will work. Thanks for your help, Deb


... Bosch Evolution 500 SHE45M05UC Stainless Steel Dishwasher

I have a Bosch SHE44C02UC/46 that will finish all of the cycle but leaves a couple inches of water in the bottom. If I pull out the dishwasher and manually active the drain pump float it will drain the remaining water out of the dishwasher. I heard about a cold solder joint on the main controller board but I am not sure if this could be the issue. Please advise wat advise you can. Thanks.


... Dishwashers

Whirlpool Undercounter Dishwasher DU8900XY1, My dishwasher is dead. It stopped in the middle of the wash cycle and has not operated since. I checked the power at the junction box and power was confirmed. I could not see or smell any burnt wires. I don't know the next thing to trouble shoot to fix the problem. Please help


Take off the kick panel and open up the j-box at the dishwasher only. Just make sure there is no burned wire nut or loose one\012\012Thanks ... Whirlpool Dishwashers

Haier ESD402 Dishwasher. Buttons on right side of control panel don't work. Replaced control board and did not help.


... Haier ESD402 Stainless Steel 24 in Builtin Dishwasher

Hello, I had a problem with my Bosch dishwasher not washing properly. I have fixed burnt out wires, replaced the water inlet valve, AND tested with a new control module. Nothing is helping. When I start the cycle, it completes the initial drain and water does flow into the unit for about a minute, maybe a minute and a half. I can hear the clicking of cycle changes but it is not washing. Eventually it will drain the inch or so of water in the bottom, but it never washes. Any help???


Hi,\015\012\015\012Welcome to Fixya.\015\012\015\012Can you hear the wash motor humming ? I`ve got a "pdf" I can send you regarding this if you want to contact me at ... Bosch SHU9925UC Built-in Dishwasher

Hi there my f&p d draw dishwasher is dead on the top draw i have tried replacing an other mother board and controll panell of another dishwasher but still no good please advise joseph.


Is it plugged in all the way? ... Dishwashers

Hi I have a Kudso1flSS1 dishwasher. I just replaced the control board and the switch board assembly, the pump is recently replaced and the filter is clean. The start button keeps flashing and the water level is always low. The DW stops running after 15 minutes and the flashing starts again...... Help!


... KitchenAid 24 in. KUDS01FLBL Built-in Dishwasher

I have a Whirlpool Energy Star dishwasher (no clue what the model is). Door will not latch. Inside of door says to press and hold ''Heated Dry'' 5 seconds to lock control and repeat to unlock. This is not helping. We rent and do not have a manual. Please help.


Happened to me today. After much head scratching I found that the screw attaching the unit to the underside of the kitchen counter had loosened and was preventing the door from closing all the way. I tightened the screw and was back in business. ... Dishwashers

I bought this dishwasher 5 years ago and was kept in the box until last month. I installed it, turned on the water and no water is being pumped into the unit from the water release valve in the dishwasher. I then checked all the cycles and everything works except for the pump. Then I checked to see if any power/volts was going to the pump and there is none. Could it be a wiring problem or could it be the circuit board?? please help. thanks


You will have to check all the connections visually. Since you know how to use a meter, see where the current stops. See if there is current coming from the control board to the pump. the water inlet solenoid valve should "free flow" water into the m ... GE 24 in. Profile PDW7800 Built-in Dishwasher

Asko dishwasher Rotu emailed with some helpful info, so here is the additional you requested. The dishwasher continues to fill as long as the water is turned on to the appliance and then it will drain. For some reason this cycle continues. The repairman said it needed a new control board. Is this the case and is there anything else I can do?


You could have a bad fill valve that doesnt close. Try unplugging the unit or turning off the power at the cuircuit breaker. (not the power button) If it still fills when you turn on the water, it just has a bad fill valve. If it does not fill, take ... Asko D1776 Built-in Dishwasher

I have a bosch dishwasher model classxx maxx freedom performance sgs43co2gb/35. the machine when turned on doesnt stop,so i checked the control panel and there was a black ring of soot,before i purchase a new control panel,what would cause this to happen? please help!!!


I think your model was part of the recall and the repair is free to fix call bosch and they will take of ity. they need to know the model asnd serial number to know if it is one of the recall ... Bosch Dishwashers

The control panel on my dishwasher will not work. I have tried the unlock button and that was not the problem...I have turned off power to it for 2 minutes and that was of no help either...Can someone please let me know what is going on with my dishwasher....


Your touch pad control panel has gone bad. The part alone is about $150. not counting a house call and labor. If this machine is over three years old I recommend replacing it. A repair without a warranty is not cost effective. Joe ... Whirlpool DU930PWS Built-in Dishwasher

Help searching for Asko dishwasher part#8801203R Board Elec Control


... Asko 1385 Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2128 seconds