Having problems with your Maytag Dishwashers ?

Main water switch has fallen out it still works but where dose it plug in


Answers :

Hi
\015\012
\015\012Not sure which water switch you are reffering to, is it the water inlet valve or something else.
The valve is located behind the Support and Toe Panel, mounted to the left side of the Tub Support. Inlet water supply to the valve is directly below the valve.
NOTE: Turn off water supply to the Dishwasher before servicing this component.
The valve is designed to operate at water pressures of 15 -120 psi.
NOTE: Low water pressure will affect the ability of the Water Valve to properly fill Tub in the required amount of time.
\015\012Hope this helps...
\015\012Daniel
Hi,

As you never mentioned the model number, let me take one of the models on which this problem is common :-

http://www.searspartsdirect.com/partsdirect/part-model/Maytag-Parts/Dishwasher-Parts/Model-MDB9150AWS/3048/0130000/M0407343/00004?componentDescription=INNER%20TUB&brandDescription=MAYTAG&searchTerm=

Look at Part 14 - That is the location of water switch.

If the above link would not help at all, kindly revert with model number, so that i could let you know the location.

Thanks and Regards
taran_2005
Repair Help & Product Troubleshooting for Maytag Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Main water switch has fallen out it still works but where dose it plug in


Hi\015\012\015\012Not sure which water switch you are reffering to, is it the water inlet valve or something else. The valve is located behind the Support and Toe Panel, mounted to the left side of the Tub Support. Inlet water suppl ... Maytag Dishwashers

Ariston LSI 41 dish washer had intermitant problem of green light not coming on when main power switch turned on and machine not working, the circuit had beed repair before. I played around and got the machine to go through a full circle once then would not go again. So I have put a new circuit board with switch etc. still the switch panel light dose not come on, i found bad connection in connector which comes from small plug on circuit board, (two red wires )I have checked for power to board. W


... Ariston Technologies Dishwashers

I have a Bosh Logic dishwasher SGS65L12GB/04 The other day it got to 1 min left and would not stop pumping out water and continued even with the door open. After 5 mins playing around it started working again for a further 2 washes. Now when switched on the pump for pumping out the water works continuously. Reset it time seem to count down but does not do anything reset time goes to 0 and beeps but still the pump runs even with the door open. all buttons seem to work fine but no washing and pu


Hi Jonathan,\015\012\015\012Welcome to FixYa.\015\012\015\012Your float may have got stuck or it's possible that you have water leaking into the bottom of the washer. In the bottom of the wash compartment, next to the drain yo ... Bosch Dishwashers

My Whirlpool Gold Series 980 dishwater no longer fills up with enough water to drive the washing arms, so the dishes do not come out clean. I cleaned the filter on the water intake valve (which was really clogged) and it still did the same thing. Replaced the inlet valve and still no change. The water does not reach the level of the overfill float switch, so that’s not it. Its been working fine for 4-5 years, what else could it be? Thank you.


I hve provided u with all details .read it carefully .it has all the resolutions for all possibilities ... Whirlpool Dishwashers

My Maytag dishwasher (DWU7400BAE)does not turn on. The latch micro-switches work; replaced the timer switch, still doesn't work; makes no sound of any kind when timer switch is turned. Could this be a relay problem, or is there a solenoid that activates the water flow?


... Maytag Dishwashers

Bosch Dishwasher model : SHV4313GB/17 The machine won't switch off and the pump is still trying to drain water ( there is no water left in machine ) The cycle seems to have finished as it has made the beep sound as if it has finished. The dishwasher is still working even when you open the main door. Have tried to reset it but to no avail. Even after turning it off at the mains it still starts up again as if in mid cycle ! HELP PLEASE


I have a SHV. My sink drain backed up, and the water accumulating in the sink then migrated to the dishwasher, through the drain pipe, causing the dishwasher to fill up and, it turned out, overflow a little. When I turned on the dishwasher, the wat ... Dishwashers

My Bosch dishwasher Model SHE44C02UC just went completley dead while washing. My wife and I were in the living room and heard a ''pop'' and went to investigate. We discovered the dishwasher was completely dead with no lights on at all. The on/off switch does not work. I checked the breaker and it is okay. Also the disposal is also on this circuit and it still works so I know the circuit is okay. There is still water in the bottom of the dishwasher - no suds - so it may have been in a rinse cycle


Well done on confirming that the outlet is not the problem. This problem will not be able to fixed by the owner and a service call is the next step. (unless you want to dig into the problem, which could easily be a failed pump motor which took out t ... Bosch Dishwashers

Defy dishmaid dishwasher does not start wash cycle. Several attempts to reset dishwasher has been done. Machine has been unplugged for several days and switched on again and still does not work. The start/stop switch have been kept in for about 5 - 10 seconds to reset. When the machine is set to do washing, the water enters the machine and wash light shows green and machine remains like that with water inside the machine. The start/stop button is again pressed for 5 -10 seconds to drain the wate


... Dishwashers

After replacing my garbage disposal, my dishwashr stopped working. I did forget to remove the stop plug from the disposal unit. But even after doing this the unit still does not work. It does turn on but no water drains out. In addition when using the sink it appears that some water may be getting into the dishwasher.


The drain line from the dishwasher MUST be secured HIGHER then the drain port in the disposal.If this is not the issue,the dishwasher drain solenoid is not functioning correctly. ... GE Nautilus 24" Built-in Dishwasher

I got a whirlpool dish washer Adp4407. When the machine is switched on it carries out the cycles but seems that the hot water cycle is not working and the dishes are still unclean even after completin


... Dishwashers

Replaced the control panel on my indesit idl 700 because it was cracked, but still working. since then will not fill with water , water is on switches all seem ok but will not fill. three beeps can be heard , which means its asking for water, what is the problem ?


... Indesit 24 in. IDL700 Built-In Dishwasher

Hi can you help me please I have a Zanussi DX6453 dishwasher which has stopped working. Having used the diagnostic facility it has come up with anti flood device, I have done the usual rocking the machine back and forth no sign of water. I have taken the machine apart and looked at the anti flood switch and this is bone dry and by lifting the float you can hear the switch clicking on and off. When I reassemble the fault is still there I'm begining to think the switch is faulty but not sure, do


... Zanussi 23 in. ZDT6255 Built-In Dishwasher

Normal wash cycle- tub fills (?), then comes a loud hummmm and nothing happens. I noticed water level didn't reach heater coil and added water until limiter switch clicked. Still just a loud hummmm. Machine was well into its regular cycle when this first occurred, but now, won't even get past initial fill. Pushing the "Cancel/drain" button activates motor and pump: they work fine.


You are an expert enough reading this. But with a terrible complicated dishwasher. First clear the waterlevel problem.\015\012Rest is a result. You do not need me, join us. Next time buy something more plain. ... Dishwashers

My Bosch Classixx is not filling with water and no sound of the pump trying to work either. I fiddled around with it as it was not cleaning bowls properly on the bottom shelf - plates and cutlery were fine! Think I might have disturbed the round dome thing - is this the "float switch"? There is also about an inch in the bottom of the filter area which I have cleaned out of gunk but still with water there. Any ideas please!


Hi, \012 \012I have an older dishwasher also and recently my wife also complained about it not cleaning right... so me being the man I am tried in vain to clean the things... Bought new spray arms onli ... Bosch 24 in. SGS43C12 Classixx Free-Standing Dishwasher

Dishwasher LFK-011S: First it occasionally gave four beeps (overflow) but no water in bottom or under. I then noticed that with lower water pressure machine worked ok few months. Now last week in the middle of program, drain pump started to run, machine gave four beeps and pump kept running even main switch off. Now when I plug in power cord, the pump starts to run immediatelly


... Fagor LFA013 SS 23 in Builtin Dishwasher

I started working with the Karcher KB4040 pressure washer and all was well for 1-2mins, then it sputered a bit and all power died. All hoses were still attached properly, it hadn't blown a fuse in my house and the fuse in the plug of the washer is working fine.When I switch it on I get nothing. Do you think the motor has packed in? I borrowed the machine from my neighbour who's away on holiday, so don't know much about age of the machine. Any advice much appreciated.


If the water is in anyway impeded, like kink in hose the unit turns off and goes into protection mode. That it it shuts down for a pewriod of time depending on how hot it may have got.\015\012When its rested try it again ensuring you definitely ... Karcher 1750 psi Electric Pressure Washer

Bosch shu8806 Hello, I aquired a shu8806 recently and it doesn't work. It has power and water. I push wash cycle, indicator light comes on, shut door and nothing happens.  So the door switch seemed like a good place to start. Since I am an electrician I thought I would give it a shot. When plugged in, the wire from the motor is 120V but when jumpered to the neutral(common on the door switch), motor doesn't operate. Although, I have heard the motor turn over momentarialy when trying to run unit e


The pump may be clogged, or the motor start capacitor may be bad or some units have a fill switch wired inline with the motor so it won't start unless the unit is full ... Bosch 23 in. SHU 8805 Built-in Dishwasher

Belling IDW604 dishwasher. Accidentally openned mid cycle, could not reset or switch off. Then had power cut. Dish washer now off and cannot be switched on or activaled at all. Have changed the plug fuse but still will not work.


The one link for all the solutions just click the link and solve any type of problem in kitchen ranges.\015\012www.applianceaid.com\015\012\015\012 the link ... Belling Dishwashers

I have a Neff Dishwasher and I think the problem is due to the cold water inlet valve. When the dishwasher starts it drains any water and then should stat to fill. If I monitor the voltage to the valve it does switch to 240V but still fails to fill. I have verified that the cold supply works OK and the filter on the inlet is clean. The dishwasher is a NEFF GB5121 and is about 20 Years old.


... Dishwashers

On an AEG Favorit 64570 VI we have an error 20. Manual indicates a drainage problem, however when we pour in water, it gets pumped out without a problem. No obstructing in the exhaust tube. Next we checked the pressure sensor, by taking it out and blowing into it. It clicked as pressure was applied to it, so the inner switch worked. Everything is clean, but still we get an error 20. What does seem strange is that the appliance does not take in water. Any suggestions are welcome.


... AEG 23 in. Favorit 86070Vi Built-In Dishwasher

Eco light comes on when I switch on machine but can't change programme and it doesn't work some water still under filter


This indicates water in the base, there is a polystyrene float that operates a cut off switch if water leaks into the base, this could be caused by a leaking pipe connection, or simply by water getting by the door seal and eventually having enough vo ... Hotpoint 24 in. FDW60 Free-standing Dishwasher

I have a Smeg dishwasher SA660 EB. Still like new . Hardley used but have problems with the timer switch not progressing past 5 and also had the thermostat replaced as a loud bang heard and the machine did not work. Since warranty on repair run out it sounds like water is leaking around the thermostat through onto electrics as loud bang noise heard again . I found the thermostat just pushes up into the rubber seal in the bottom of the dishwasher. I have taken out the rubber seal as this also loo


... Smeg Dishwashers

Kenmore dishwasher... filled up with water and its lights went off.. no buttons work acts like no power. check the house fuse box - ok ... check the 2 door switch - ok .. checked the thermal fuse - ok ... so, i picked up a new board and changed it out. still wouldn't run.


Did you check power to the unit? Double check the common and grounds. When servicing I will disconect(unplug from wall) power to the unit. Is it pluged in? Use another outlet(the outlet under the sink may be wired thru a switch for a disposer)even ... Kenmore 24 in. 16032 Built-in Dishwasher

Belling IDW604 Error E4 coming on machine, I have drained all the water from the machine and switched it off and back on again at the wall and it still isnt working. Can you please help????????


I found the solution myself. Underneath the machine, there is a plate. \015\012On the plate, there is a float and a\015\012 microswitch, when the water leaks onto the bottom plate it raises the \015\012float and activates the microswith which shuts d ... Belling 24 in. IDW603 Built-in Dishwasher

Got a Diplomat ADP8322. Starts Cycle then starts bleeping 3 flashes which is a heating error. No hot water at all. Had a look and cleaned watr pressure switch still not working. Any ideas has the heating element gone.


Possibly heating element - only way to find out is to check continuity with a multimeter.there is also a thermal cutout in series with the heater which could also have gone ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1719 seconds