Having problems with your Maytag Dishwashers ?

I have a Maytag dishwasher MDBS561AWW that doesn't start when the start/cancel button is pushed. Power is on. Water is on. All of the other buttons seem to function as you can cycle through all of the other settings and the lights respond.


Answers :

Repair Help & Product Troubleshooting for Maytag Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a Kenmore 665.16039401. The 3 right hand buttons on the keypad; Delay Hours, Cancel/Drain and Start/Resume do not respond and I cannot start the washer. Doing the self-diagnostic test by pressing "Heated Dry - Normal Wash - Heated Dry - Normal Wash" results in all of the LED's lighting and the washer starting a full 20 minute self-test cycle in which all functions seems to work properly. Opening and closing the door during this testing stops and then re-starts the washer appropriately


... Dishwashers

I have a Maytag dishwasher MDBS561AWW that doesn't start when the start/cancel button is pushed. Power is on. Water is on. All of the other buttons seem to function as you can cycle through all of the other settings and the lights respond.


... Maytag Dishwashers

Quiet Guard Delux Model 665.13742K601 Dishes are not getting clean although some areas in the washer get cleaner than others. Detergent dispenser is not being fully cleaned and is caked with detergent after operating. In addition, the only "Cycle" light that seems to be working is the "Pots and Pans" cycle and the status lights also seem not to be functioning.


... Kenmore Dishwashers

DU1145XTP The buttons don't all work--for a while the normal wash and heated dry were the only functions that worked--now the start button doesn't work. I took the panel off and clicked the door switch and held it and got all the cycle buttons to light up except rinse only and only heated dry in the cycles would light up. The delay buttons don't work and neither does start. Also the panel seems hot.


You need to replace the circuit board inside the machine, technically it is possible for you to do it, how long have you had the machine, if it is under warranty you can have it serviced without any cost or less cost to you contact Whirlpool ... Whirlpool 24 in. DU1100XTP Built-in Dishwasher

Frigidaire Gallery Series Dishwasher - unit stops near the final rinse cycle without draining - "ER" on front display, all led indicators on front display also lit (e.g. low rinse agent, etc.), and the "Hi Temp Wash" light is lit, regardless of cycle setting at beginning of cycle - rinse cycle seems to function normally


HI,check your drain hose first for kinks or food blockage also check the\015\012tail at the disposal or wherever you drain hose connects. Second there\015\012may be a blockage in the pump itself take it off and check. If all of\015\012thi ... Dishwashers

We have a Kenmore Elite Dishwasher #665.1646 - 5yrs old. On Friday nite, there were no problems but last nite the lights would not go on when cycles were pressed ( or Start). Checked the circuit breaker and it was OK. There is nothig caught in the bottom and the overfill float is functioning. I pressed Hi-temp and Air dry alternately and all the lights lit. I pressed Smart Wash, then Start and it did not go on. I can hear it draining but no water seems to flow and then it stops. All light t


The thermal fuse on the control panel. There isa couple of wires that lead up to a white box with the fuse in it. Thatis the problem. If you are good with a volt meter or light and youplace it across the fuse, if it is bad the light will light ... Kenmore Dishwashers

I have a maytag mdb6650 aww dishwasher. The dishwasher just stopped. The light on the control panel is on. If I push the buttons to try a different cycle, the light over light wash remains lit, so the buttons don't seem to respond. I was wondering if it is the control assembly, or if the door switch is not working. The handle cracked a while ago, but if the dishwasher still worked even though the handle had cracked in half.


... Maytag 24 in. MDB6600A Jetclean II Built-in Dishwasher

Dishwasher wont let u select a cycle...all buttons seem locked...ive unplugged it for 5 seconds or so and then plugged it back in and the normal wash button light comes on and the heated dry button light comes on, but it wont start and it doesnt respond when buttons are pushed...please help. thanks


... GE GLD4560NSS Stainless Steel Built-in Dishwasher

The dishwasher seems to be making excessive noise prior to commencing wash cycle.the eco setting is not functioning but the 65 degree wash setting is. sometimes the wash cycle just doesn't start and all of the wash program setting lights flash repeatedly.


... Smeg 24 in. DWD612SS Built-in Dishwasher

Kenmore elite dishwasher...seems to have shut down mid-cycle...no clean light this morning...inch of water in the bottom...panel not responding....have power to one side of the start button


... Kenmore 24 in. 16032 Built-in Dishwasher

Whirlpool Quiet II (DU110XTPB1)... Two problems (maybe it's one)... Start/resume light flashing and won't stop. I have tried on the different button combinations from this website and other websites and none of them seem to make a difference. The flashing continues. That's problem number one. Problem number two is that it seems to go into some sort of washing cycle in completely random intervals. When it's in one of the random washing cycles the following lights are on; Normal Soak and scour


Hope it's under warranty, maybe logic board, poor motor design causes main PCB failure ... Dishwashers

I have a kitchen aid dishwasher that is stuck on the clean cycle. It will drain water, but no water seems to be getting into the washer. If i push the start button, cycle will not start. The clean light is the only light that will stay on. the other lights will go on, but they eventually go off without starting the cycle. Is this the thermal fuse???


... KitchenAid Dishwashers

Our AEG Favorit 50620 dishwasher won't start. When I push the power button, the power light comes on, but none of the other lights. Pushing the function buttons has no effect. The door is fully closed, and it was working perfectly before. I have tried turning it off and on, unplugging it etc. Nothing works. Interestingly, if you push more than one function button at the same time, some of the function lights come on, but then when you try to start the cycle it still won't work. Help!


... AEG 24 in. Favorit 40650 Free-Standing Dishwasher

I used the "rinse only" cycle on the dishwasher a little while ago. I've never used this cycle before. After dinner I tried to start the dishwasher, but no other buttons on the panel respond except the last one I used, which is the rinse only cycle. I push and push, I tried pushing and holding, nothing works, I get no lights no anything. I've been using the "light wash" cycle for a long time and I normally just push the start button and the last cycle used starts automatically, so I wasn't a


Try un-plugging the dishwasher (check for cord under the sink) or turn off the breaker to it to re-set the control board. If this does not resolve your issue you may have a defective key panel. ... Dishwashers

Hotpoint LFT 114 dishwasher Cycle seems to run OK BUT water cold. No flashing of lights to indicate error, lights appear to behave as normal. Metered the heater element, not open circuit or short circuit. Metered the NTS resistance goes down as temp goes up Dismantled and checked all connections, all seem good. Ran the self test program and it seemed to get stuck in the wash stage, never seemed to move on BUT no error message. Now what, any suggesting please guys??


... Dishwashers

We have the G841SC+ Miele dishwasher. The intake/drain light blinks and the cycle stops on economy and sani wash before the end light comes on. The normal cycle seems to be able to complete a full cycle. Is there anything we can check.


... Miele Dishwashers

My wife opened door during cycle. When she closed door it would no longer run. Looking at problems and recomendations on similar models, I replaced the board. Did not fix the problem. I have checked the fuse and the door switches for continuity and all seem ok. The only lights on the panel that come on are: under cycle- Pots & Pans, Light. Under Options - Heated dry. No other lights work and the dishwasher does not operate.


Hi,\015\012\015\012First off, sorry to hear that you replaced the control board for nothing..in hindsight. So if I understand what you're saying is this, You cannot select any cycles and the unit won't start...because the start button is ... Dishwashers

The touchpad buttons no longer work to select a wash cycle. When I push "Start" the light above "Smart Wash" comes on and the dishwasher operates normally, but I cannot select any other cycles and the light only comes on after pressing "Start", not before. Also, the Options buttons seem to work normally but the delay button doesn't scroll through 2-4-6, it only toggles the light on and off above "4". The item is 15 months old. Thank you.


... Kenmore 13743 Staimless Steel Built-in Dishwasher

Cycle interrruption Recently, about 20 minutes into the wash cycle, the unit shuts down and the lights start blinking - usually "Pots & Pans" & "Quick Rinse" simultaneously. No other buttons respond and I cannot get it to finish the cycle. Only shutting down the unit at the fuse box eliminates the lights. I've checked for blockages and nothing found. Manual does not offer any help or suggestions. Any ideas??


Relace control board. ... Kenmore 24 in. 16032 Built-in Dishwasher

Our dishwasher is no longer cleaning dishes very well and usually the detergent tab that we put in does not dissolve completely. Our dishwasher is a General Electric Model # PDN7800G00WW and several years old. The water here is very hard. On a separate note and a new development is the control panel seems to be messing up. When we press the ''speed cycle'' which is normally 37 mins it goes to 86mins and lights up the ''speed cycle:'' button. pressing the ''glass cycle'' lights up the adjacent '


Hi,\015\012\015\012There are various reasons for the Dishwasher not cleanig the Dish properly, From your query we can understand that, it must be issue with the Dishwasher selecter switch..\015\012\015\012DISHWAHER SELEC ... GE 24 in. Profile PDW7800 Built-in Dishwasher

I have a Sears Kenmore Elite Ultra dishwasher 665.1315 model. For the last 3 weeks, it keeps having the clean light blinking 6 times pause then 1 blink and pause and repeats cycle again. I have turned off the breaker...I have reset by pressing the heated dry and normal wash until all lights are flashing. It then completes some type of cycle and looks ok. When I opened the door, steam came out and all was hot inside. However, once I try any new wash cycle, it seems to wash but after 1-2 hours and


Call sears service and tell them you need service there is a service flash and will be no charge ... Kenmore 24 in. 15932 Built-in Dishwasher

I have a Whirlpool Gold Quiet Partner III (Model GU1200XTKB0). I have used it previously on "Normal" cycle and I always keep it on Air Dry. Last night I used the "Pots and Pans" cycle and it seemed to work fine. But this morning the Air Dry light is flashing and if I press a cycle key the Rinse Only light starts to flash as well. Nothing works. I have made sure that the console is not locked. Any suggestions? I do not have a Heated Dry button, only Air Dry. Thank you.


... Dishwashers

PDW9280J10SS dishwasher has been in use for about 3 years. The control panel is not working properly. I use the up/down arrows and it turns on heated dry etc. When I push the heated dry button, it changes the lights to the different cycles (which is what the arrow keys used to do). The normal wash light won't come on, the only setting that seems to wash a full cylce is antibacterial. It seems like something burned out. What should I be looking at as a possible cause/fix. Unfortunately, I don't h


... GE 24 in. Profile PDW9280JSS Built-in Dishwasher

Dishwasher is not drying. At end of cycle, dishes are still wet and damp, as well as the inside. Buttons are all pushed. Also, it seems to wash for more than one cycle. Did a light wash and after 1-1/2 hrs., it was still running. Purchased a couple of months ago. Dishes don't seem to be as clean as my old dishwasher.


Hi,Check your heating element.. A bad heating element causes many problems in dishwashers…Dishwasher Problems The ... Whirlpool MDBH969AWB Builtin Dishwasher

My kenmore dishwasher will run part way thru the wash cycle, stop and the hi temp and heat dry lights will flash back and forth and not do anything else. When you open the washer it will have water in it that has not pumper out. It seems that the light wash cycle will work after trying the regular or heavy wash. The washer is 1 1/2 years old. model # 587.15259402


First cut power for ten minutes by unplugging power cord or tripping circuit breaker.If that does not work try the following reset.Press in succession:High temp-air dry-high temp-air dry - High temp-air dry-high te ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1476 seconds