Having problems with your Maytag Dishwashers ?

Where is the filter on a maytag MDB7100;MDB7160. How to remove for cleaning or replacement?

\015 Model MDB7100.MDB7160\015

Answers :

Repair Help & Product Troubleshooting for Maytag Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Where is the filter on a maytag MDB7100;MDB7160. How to remove for cleaning or replacement?


... Maytag Dishwashers

My dishwasher spray arms were clogged with calcium buildup so I cleaned one and replaced the other. I also removed the fixed disc-shaped device underneath the lower spray arm and found the particle filter was clogged- so I cleaned it out. The dishwasher ran fine for a few times but then the filter clogged again, and again, and again. Now I need to make a routine of disassembling the parts to get at the filter every week because the filter no longer clears itself during the wash and/or emptying c


You may want to check your hot water tank. It may need drained and cleaned, Or you may have the rod in the tank disintegrating. Also check you water faucet areators to see if they have calcium pieces too. ... Maytag Dishwashers

Clogged filter I have a Maytag JetClean EQ Plus (model number MDB9150AWS) and the filter under the lower arm is clogged and I don't know how to clean it. I can remove the filter, but it has several "windows" covered in mesh in which I can see debris, but I can't figure out how to open these "windows" to clean them. And how can I prevent the clogging to begin with?


Hi, The mesh does not open. You will need to GENTLY clean each section with running water. Are you using powder or liquid soap?The most common thing that plugs them is food particles. This unit is best served by pre-rinsing the dishes. The mess ... Maytag 24 in. MDB9150A Built-in Dishwasher

JENN-AIR Model number JD3B10AWX. Bottom of dishwasher is dirty, I want to clean it. I have removed six screws holding plate down, but cannot find any way to remove spinning blade. I think there's a filter underneath that I can clean or replace. Questions: 1. How to remove spinning blade? 2. Am I going about this correctly. Thank you


We have been having issues with our model where there is dirty sand deposited inside of glasses and dishes.You need a torque wrench for a triple square torque screw ... Jenn-Air Dishwashers

I have a GE dishwasher (GSD4020Y70BB) new in 1996. I replaced the whole motor assembly in 2007, seal was leaking. My dishes are not getting clean now, dried food left on plates, coffee stains in cups not being cleaned. I removed main spray arm, found nothing, turned washer on and plenty of water gushing out. I took the cover off sump all clean. I removed the filter screen in the back, there appears to be a valve with some soft rubber around it. Water gushes out of this, does stop during the cyc


Have you checked the drain pump impeller and drain hose? I am curious if there is a back siphon from the drain hose or the waste outlet at the garbage disposal might be blocked or plugged with food debris.\015\012I wou ... Dishwashers

Bosch 24in. SGS69LO2 Logixx Our machine runs but there is no water coming into the machine?have removed pipe to check water flow,ok, have removed the filter for the inlet supply,clean.have cleaned all filters and replaced, reset the programs, but still no water into machine.


... Bosch 24 in. SGS69L02 Logixx Built-in Dishwasher

Dishes all cloudy and spotty. Maytag Intellisense plus 1996 dishwasher. I have real hard water that leave white calcium build up. I can remove and clean all of the lower spray arms and filter. How do I remove top spray arm to remand remove deposits? The motor sounds good, hot water, fill ok. On the inside top of center of arm where it meets the center input connection there is gunk to remove. How do I get to it? remove arm? thanks


The problem is hard water. Go to www.dishwasherfilter.com. They have a new product out that solves this problem once and for all. It filters the water entering your d ... Danby 22 in. DDW399 Free-standing Dishwasher

Circulation pressure is low. I removed and cleaned the filter basket and the fine-filter in the bottom. Do you think I need a wash motor, circulation pump? Am I on the right track? Is this difficult to replace? If so, any tricks to share. Thanks in advance.


... Bosch 24 in. SHV66A03 Built-in Dishwasher

Frigidaire Dishwasher gld2440reb1. After removing filters, cleaning and replacing them I had three flashing lights ie Sensing, Clean and Sanitized. all buttons were inoperable. after unplugging and reconnecting I had a PF or power failure indicator. after pushing the start button the PF went off but no further action from any button. Help!


Usually if you get a PF error that means you have received a power failure usually from the control board shorting out on this model. Typical reasons the control will short out is from either the circulation motor shorting or pump motor shorting. If ... Frigidaire Dishwashers

Maytag jetclean mbd4100 filter is clogged. How can I remove it?


... Dishwashers

Removed the bottom filter of a GE Quietpower 3. Cleaned the screen and replaced the unit, now the machine does not drain. I assume the screen and the part under it can go in one way.


Hello, luckyI\012 was trying to help you out here. I am not sure if this well help you? \012But here is a link to about everything you want to know about your \012dishwasher, from repair to trouble shooting on most common dish ... Maytag Dishwasher

My Maytag MDB7130AWB dishwasher is leaving detergent residue on the dishes. I removed the lower spray arm and filter screen. The screen was very clean with no mineral build-up. What could the problem be?


This is going to be more of a problem as the dishwasher detergent manufacturers are removing phosphates from dishwasher detergents. You can buy phosphates (or STTP) from various sources on the internet. It's called Sodium Tripolyphosphate. It's about ... Maytag Dishwashers

We've got an Meile Incognito dishwasher, model G 843 SCVi plus. It purges at the begining of the cycle and then seems to fill with water, but then the red Intake/Drain light starts to flash and the cycle goes no further. I've removed, checked, cleaned and replaced the triple filter and the drain pump but the light is still flashing. I spun the propeller both ways, no problem there. Any ideas for me?


... Miele 24 in. Incognito G843SCVi Built-In Dishwasher

I have a maytag MDB600AWW dishwasher. the top spray arm doesn't turn. it wouldn't even turn if i removed the to middle trays. I took the accumulator out and cleaned it. the fine mesh filters were clogged. unfortunately, birthday candles found their way into the machine sometime back. i cleared as much as i could. when i put it back together, the top arm would spin only when i had the 2 middle arms disconnected. It seemed there was an increase in pressure. i ran a diagnostics test and there were


First check to see if the washarm itself is clogged, if so clean it out.\015\012\015\012If the arm has a bearing it may be shot.\015\012\015\012You may have a clogged manifold on the output side of the pump. I sometimes run a ... Dishwashers

Maytag Quiet Series 300 dishwasher leaves sediment on dishes (primarily glasses) after running the Autoclean cycle. We've taken it apart, cleaned spray arms, filters, float and replaced some seals, but still have problems. We use Cascade detergent and Jet-Dry (what was recommended when we bought the dishwasher). Our water temperature is 120 degrees (maximum setting we can have without having our tankless water heater modified), but this dishwasher problem was an issue with our old tank water hea


The problem is hard water. www.dishwasherfilter.com has a\012product to solve this problem once and for all. It filters the water going into\012your dishwasher and remov ... Maytag 24 in. MDBH950AWS Built-in Dishwasher

I have a whirpool Quiet Partner III, and the top layer of glasses is not getting clean. I had a technichian out some time ago, and the problrem was caused by food debris trppaed in the filter in the wash module. He saud it was easy to clean that out, so I have removed the lower spray arm, but cannot undo the 4th screw that will allow me to take the grey round filter cover off to remove the food or paper debris. It is under the white flat pipe that delivers water to the wash module, and I cannot


I had same problem, would not clean well and fixed it. . I cracked open the door during wash cycle and used screwdriver to defeat the door lockout. The water from the bottom sprayer was only shooting half way to the top of dishwasher. To fix I remove ... Whirlpool Dishwashers

We recieved a dishwasher that had tons of lime and scale. well i remove that mostly by hand by taking the bottom part and disassemblying it and soaking it in CLR and slowly removing the calcium lime and whatever else there was. but i am kind of a thorough person and the bar =on the back of the dish wash needs to be removed and the back of it cleaned and probably soaked also if not replaced but i will just clean it for right now if i can. HOW do you remove it? I need a step by step on how to remo


Instead of going through all that effort, and still not being able to get to everything, just use a product called "Dishwasher Magic". It is a dishwasher cleaner and disinfectant, and cleans limescale and rust out of the dishwasher by just running i ... Maytag 24 in. MDB4600A Built-in Dishwasher

Draining problem GE dishwasher pdw7880 won't fully drain. I have cleaned all filters and baskets. If the fine filter assembly is removed, then it drains fine. When in place it drains very slowly to not at all. The fine filter assembly looks fine and is clean.


... GE 24 in. PDW7880JSS Built-in Dishwasher

I have a MODEL 577-0 kudk01ILb55 KITCHENAIDE dishwasher. I am trying to remove the inner pplastic bar that goes vertically through the system from top top bottomj so that I can clean out the filter. But I do not see how to remove that bar. I have looked online for a repair manual of some type but have been unsuccessful. Can someone tell me how to remkove the bar so I can get to the filter on the bottom? I have already removed the star shaped rinse sprayer.


... KitchenAid 24 in. KUDS01FLBL Built-in Dishwasher

WONT WASH CLEAN ALWAYS RESIDUE LIKE SAND ON GLASSES ETC. THAT IS ALMOST IMPOSSIBLE TO EVEN REMOVE BY HAND WASH ENOUGH SALT AND RINCE AID ALSO CLEAN FILTER EACH TIME NO OBSTRUCTION IN PUMP FILTER THOUGH HAS AN ORANGE COLOUR SALTLIKE SUBSTANCE INSIDE BRAND NEW MACHINE STARTED WITH BAD WASHING RESULTS AFTER COFFEE PLUNGER WAS NOT CLEANED PROPERLY AND GROUND COFFEE LANDED IN MACHINE ALSO POSSIBLY OUR HOUSECLEANER MIGHT HAVE USED ORDINARY TABLE SALT INSTEAD OF DISHWASHER SAL


Use CLR to remove any build up and then use LEMI-SHINE (walmart in dishsoap aisle) for the cleaning of your dishes. Works great for me as i have the worst well water on the planet. ... Dishwashers

I have a KitchenAid KUDS03CTSS3 and the longer I own it the worse it gets. At 1st it was a great, but as time goes on it doesn't barely clean a thing... It's frustrating me to have to rewash everything by hand. It has a filter system that isn't removable for cleaning... what do I do now? I'm sure if I could clean the filter it would be fine. Someone please HELP!! :) Chantal


... KitchenAid 24 in. KUDP02FR Built-in Dishwasher

Dishes and glasses not getting clean. Visaul inspection; it lloks fine. Removed filter and bottom perforated filter panle and cleaned off mineral-like residue. ran test program: result flashing lights for Clean & rinse/dry buttons. not sure of next step...help please.


Hi,The scum, film and white\012residue problems have started since the reduction of\012phosphates in dishwasher detergents.Here is a tip that\012will help you to solve the problem of films, residue, and scu ... Bosch 23 in. SHU3307UC Built-in Dishwasher

I have a maytag mdb4000aww dish washer. The dishes aren't getting consistently clean. I wanted to clean the trap/filter. There's two ports towards the front side. The one on the right i was able to remove and clean. The one on the left moves up and down but i can't seem to be able to remove it (without breaking it). Any advice? Thanks


What must I do if the rinse compartment is plugged???\015\012help please. My moms dishes are piling up. my hands are all pruiny from hand washing!!! ... Dishwashers

Hi, I have a Miele dishwasher G2150 that after 7-10 minutes on any cycle the rinse, dry, and end lights flash amber. I called the 800 number and they walked me through the diagnostic sequence and they said it was an error code 12 something to do with water restriction. I removed and checked the bottom "L" filter(clean), the wheel (moves freely, not dirty), and the grey in line filter screen on the intake hose,( clean also). I can feel the water coming through the intake hose, water comes in thro


... Miele G2150SC Dishwasher

Hi I have a Meile G 685SC Dishwasher. It has a water inlet problem. It will not fill and just keeps cycling through the water filling process with the water inlet light flashing. I have taken off the inlet pipe and removed and cleaned the inlet filter and washer and put them back. The filter was blocked with a sand like substance. I have taken apart the antiflood valve also attached to the inlet pipe but it is gel sealed so unserviceable. The inlet pipe itself on removing from the vlave appears


Check that the stopcock is opened fully or whether the water inlet hose\015\012is kinked...Check that the water inlet filter is not clogged and clean\015\012it, if necessary, as described in the operating instructions....Check\015\012that the drain p ... Miele 24 in. Incognito G643SCVI Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1107 seconds