Having problems with your Maytag Dishwashers ?

Maytag MDBH965AWB power supply board - Maytag Dishwashers


Answers :

Repair Help & Product Troubleshooting for Maytag Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Maytag MDBH965AWB power supply board - Maytag Dishwashers


... Maytag Dishwashers

I have a Maytag MDBH 965AWW Dishwasher. I replaced the latch assmembly because the handle had cracked. I replaced it with Part w10130697 from Johnstone Supply. Now when I power the dishwasher up I


... Dishwashers

Continuous alarm after a power failure an alarm started going off in the door of the dishwasher. the push button panel is not functioning. I opened the door panel and found an electronic control circuit board. It is this board that is making the noise. I unplugged the black and white pair of wires on the lower right side of the board and the noise stopped. this must supply power to board. Anyone know what this problem is?


I posted this under "Ben's" problem as well, but I had the exact same problem. I know which black and white wires you're talking about. I don't know what causes this, but getting new parts did fix it. The black box that all those wires go into on ... GE 24 in. Profile PDW9880JSS Built-in Dishwasher

I have an Asko 1585 dishwasher. It drops the inlet valve on step (step 12), and the recirculation pump (next step) tries to pump with no water. Later at about step 47, the inlet valve begins to work again and the dishwasher finishes the cycle without a problem. I have had the board checked, and all of the power supply and transfer circuits are good. That leaves the processor. Is there any combination of buttons to press which can completely reset the controller board?


... Asko 24 in. 1585 Built-in Dishwasher

I have a Maytag MDB5601AWB dishwasher. all the switches except the heated dry switch are not working. I did the unlock thing and still nothing . Do I need to replace the switch panel or is there something I should try? I tested for power and have 120 volts coming into the circut board and through the door switch Comments: Aug 22, 2009 - I tested the door swich and I have power on both poles when it is closed. there is 2 switches on the latch but the one with power to it powers up the circ


... Maytag 24 in. MDB5600A Jetclean II Built-in Dishwasher

Maytag dishwasher, has dead control consul, does have power to the board and the latch swithes are good. is there a way to troubleshoot the touch pad? replace the console or the board, or both? thanks, Bruce


The only way possible to see if the touch pads are working is to test the voltage of the control pads when it contacts. The input of the Microprocessor should be checked for the pad control inpulse to come in. If there is no trigger voltage to the mP ... Maytag Dishwashers

Good day after the power is turned on to my brand new kudc03fvss dishwasher, nothing happens. have made sure that the power supply is ok and that the door is properly closed. there is 115 volts at the circuit board inside but nothing happens. no lights, no response to switch etc. just dead. need some advice


You said your getting 115 volts and that is across the power wire and its neutral not a power and ground.. i had a case like this last week and when i got there the unit had power if tested from black to ground but not from black and the white neutra ... Dishwashers

Maytag dishwasher, control panel is dead, has power to board,but there are no lights on the panel when you close the door, like it normally would. any ideas I replaced the board with no succes. thanks Bruce, B&L Appliance


I think you have diag your problem . your have power to the board . so the inter lock switches are ok . and no lights . if you look at the printed pc board i think yoy may be able to see that one or more ... Maytag MDB5100A Dishwasher

I have a maytag quiet series 300 dishwashers with no lights on. I check the power it ok, I open the panel and all there was is a circuit board, What should I do?


I would check to make sure you have c=voltage at the bottom behind the toe kick you will find the wire connectors make sure you have correct voltage there,,,,,\015\012 then i would check to make sure you had voltage at the door switch and bey ... Dishwashers

I have a Maytag dishwasher MDBM601AWW. The control lock on the control pad will not unlock. I replaced the electronic control board and it worked for one wash. Control lock engaged again. I shut down the power and pressed the control lock for 3 seconds as directed by the owners manual. No luck. Please help Rich.


You have to power the unit back up and then holld the lock in for three seconds, if ths does not reset it then the console not the control bord needs to be replaced it comes with a new touch pad ... Dishwashers

I have a Maytag MDB5601AWB dishwasher. all the switches except the heated dry switch are not working. I did the unlock thing and still nothing . Do I need to replace the switch panel or is there something I should try? I tested for power and have 120 volts coming into the circut board and through the door switch


Possible switch panel. When you press it does it feel like a click as the the other buttons? If so you probably have a bad circuit on the inside, if it doesn't click the heated button switch is more then likely the cause. ... Maytag 24 in. MDB5600A Jetclean II Built-in Dishwasher

Hi Maytag dishwasher, model#MDC4650AWW has power to control board but no responce from any buttons.Finished a cycle & wouldn,t start again.Door switches are okay. Rene


Hi\015\012\015\012Please check the wiring connections to and from control board, also make sure that the keypad connections are good. Make sure that there is no moisture on control board/keypad. This is an issue with the wiring, use the b ... Dishwashers

My maytag jetclean dishwasher (model MDBD820) won't start. The power supply is fine. Why won't it start?


... Maytag MDB9600A Jetclean II Built-in Dishwasher

Maytag dishwasher MDB7709AWS2 - control board failed - fitted new - when power switched on unit drains even with no water in machine then after 30 seconds wash light comes on then after another 30 sec


... Maytag MDB7709AWS Stainless Steel Builtin Dishwasher

My dishwasher stop working in the middle of washing cycle. The water has not drained out completely. I attempted to restart the dishwasher but it appears there is no power. I checked the power auto swithch/fuze on the master fuze board. There is still no power going through the dishwasher.


... Dishwashers

Frigidaire Dishwasher PLD2855RFC1 Power failure code keeps going off but power supply is good. Anyone know the fix?


... Frigidaire Dishwashers

Maytag dishwasher has no power changed control panel and thermal fuse still no power...cb ok outlet ok power under dishwasher ok.....still no power


Hi\015\012\015\012Please post back with the manufacturers name and model no of your Dishwasher for further assistance.\015\012\015\012Daniel ... Dishwashers

I have a KitchenAid dishwasher model KUDC10IXWH1 that has no control power. I have already verified that there is 120V at the control board. The unit kept the lights on after the cleaning cycle was done and I couldn't shut them off. I reset the electrical breaker and now nothing works, but the board has power. Please give any advice you might have. I was thinking of replacing the board, but I'm not sure if it is the board or the front control panel. Any way to tell?


... KitchenAid 24-in Built-In Dishwasher White ENERGY STAR KUDC10IXWH

Bosch Dishwasher (model SHU43C05UC17/17) will not power power on after stopping in the middle of a wash cycle. AC power is present at input and water supply is connected and supplying water.


... Bosch 24 in. SHU5305UC Built-in Dishwasher

An electrical panel breaker switch was replaced after the microwave and dishwasher both lost power. The microwave works after replacing the main panel breaker. However the dishwasher will not show any power. Checked the internal circuit board, no burned areas, cannot find an internal GFI reset, what can I do to get power restored to the main control panel or even the unit itself? Rick C


1)check any fuse in the circut board.(blown off)\015\0122)check any loose connection of neutral (or)phase wire to the machine(or)in the switch. ... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

Maytag dishwasher I have a Maytag dishwasher 2001 Mod# MD85100AWB - Ser# 25257529ZD. I can not get it to run again after the last wash. The lights (clean, rince only, light wash, heavy wash, heated dry) continue to blink and won't clear. I tried to power it down and that did nothing. Do you have a suggestion to what I can do to run my dishwasher again?. Thx, Richard


... Dishwashers

Dishwasher would not work and clean light would blink seven times. Asked an expert and they said to hit saniwash and heated dry two times. This work for a couple of times but now the dishwasher acts like there is no electrical power goimg to it. I tested the power with a voltmeter and there is power going to the circuit board.


Normally this happens when the dishwasher electronic control does not detect a water temperature increase during the main wash cycle. The issue could be in the heater element, the thermostat or the wiring that is connected to those or on the electro ... Dishwashers

Hi. I had f1 appear on my Gisher and Paykel dishwasher. Unplugged from wall. Few days later dried using a hairdryer. Took cover off pcb board and dried in there as well. There was water on bottom of cabinet so understand the F1. Problem is now, I put cover back on pcb board and tried to power up but it is dead? Any sensor.microswitch on PCB cover, or anything i may have missed? No power at all to unit? Any assistance greatly appreciated. PS - Wall socket finer as powers other appliances.


Wait.................. ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Unit does not power up. checked power to unit ok checked power to latch switch - ok appears circuit board is bad. Traced 120v to board. Any other checks before getting new dishwasher?


Hi mgray770,\015\012It sound like you have done a good job already, but just a couple thoughts before you go buy a new one. If the board does nothing then it could be locked, check your owners manual or whirlpool.com for the exact unlock inst ... Whirlpool Dishwashers

Hello, my Siemens integrated dishwasher no: SE64M359GB stopped working mid-cycle with 35mins remaining. It is displaying the red tap emblem. Usually the dishwasher starts when the dishwasher door is closed fully (having pressed the power button). However, it is making a noise as soon as the power button is pressed. I have checked the water supply and pipes and they are OK. The filters are also clean and OK. We have an electric de-scaler on our system so I imagine calcium build up should n


... Siemens Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2099 seconds