Having problems with your Maytag Dishwashers ?

Touch panel will not respond to all requests. Wash cycle will start but will not complete through the rinse cycle. The only light that will eliminate is the rinse button.


Answers :

Repair Help & Product Troubleshooting for Maytag Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Touch panel will not respond to all requests. Wash cycle will start but will not complete through the rinse cycle. The only light that will eliminate is the rinse button.


... Maytag Dishwashers

When I start the top drawer it defaults to 5 minutes (with the lights Heavy, Fast, Rinse highlighted) runs for a couple minutes, then stops and the LED starts randomly cycling through all kinds of codes very quickly. There is water in the tub that has not drained after completing the couple minutes of operation. This cycle repeats itself if I hit the power button again after the LED starts freaking out. The 5 min cycle shows in the LED, sometimes with the no circulation error, sometimes with the


Here is the solution: \015\012http://applianceguru.com/forum1/24814.html ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Cycle interrruption Recently, about 20 minutes into the wash cycle, the unit shuts down and the lights start blinking - usually "Pots & Pans" & "Quick Rinse" simultaneously. No other buttons respond and I cannot get it to finish the cycle. Only shutting down the unit at the fuse box eliminates the lights. I've checked for blockages and nothing found. Manual does not offer any help or suggestions. Any ideas??


Relace control board. ... Kenmore 24 in. 16032 Built-in Dishwasher

I used the "rinse only" cycle on the dishwasher a little while ago. I've never used this cycle before. After dinner I tried to start the dishwasher, but no other buttons on the panel respond except the last one I used, which is the rinse only cycle. I push and push, I tried pushing and holding, nothing works, I get no lights no anything. I've been using the "light wash" cycle for a long time and I normally just push the start button and the last cycle used starts automatically, so I wasn't a


Try un-plugging the dishwasher (check for cord under the sink) or turn off the breaker to it to re-set the control board. If this does not resolve your issue you may have a defective key panel. ... Dishwashers

DU1145XTP The buttons don't all work--for a while the normal wash and heated dry were the only functions that worked--now the start button doesn't work. I took the panel off and clicked the door switch and held it and got all the cycle buttons to light up except rinse only and only heated dry in the cycles would light up. The delay buttons don't work and neither does start. Also the panel seems hot.


You need to replace the circuit board inside the machine, technically it is possible for you to do it, how long have you had the machine, if it is under warranty you can have it serviced without any cost or less cost to you contact Whirlpool ... Whirlpool 24 in. DU1100XTP Built-in Dishwasher

My Whirlpool ADP6565 dishwasher stops before the rinse cycle. The start button then flashes and the rinse light on the cycle selelector knob is lit up. if I hold the start button in the water pumps out and then stops. I have to manualy set it to rinse to rinse the dishes.


You may have a blocked faulty, pressure sensor, or the hose is not flowing freely? Check that out.\015\012\015\012Below please find a service and repair manual, if you use the troubleshooting steps you maybe able to isolate your issue, and affe ... Dishwashers

Kitchen Aid Dishwasher - model: KUDPO2CRBLOrn Ran the dishwasher twice on pots/pans cycle and sani rinse with a special cleaner recommended due to build up and items not getting clean. (soap left all over them) Cleaned machine out great! Now, the only choices that will light are "quick clean up" and "rinse only." Even if I choose them, when I hit the "start" button - the machine will not start. No other lights will light. Machine will not start. Any ideas?? Thank you!!!


... KitchenAid Dishwashers

"Quick Rinse" light blinks constantly, unable to select "start" unable to select "normal wash" sometimes can select "pots and pans" but still not able to start. Was working normally, when it stopped at end or pre-rinse to start the main washing cycle, the "quick rinse" light came on blinking, and no other button works except as described above. Thanks,


Hi,\015\012 \015\012Check out the console assembly. take off the inside cover and the plastic over the electronics, just remove the two screws holding down the circuit board, pull it to the side, then blow ... Dishwashers

I have a Whirlpool ADP6515. It's been working fine for about 2 years now but recently cycles are not completing properly, it can run for 30-40 minutes depending upon cycle. The start light is flashing a 4 times repeatedly, I think this happens when it moves from a wash to a pump cycle but not sure. We have to hold down the start button to force it to go to the end of the cycle and the the lights stop. If we do that we can then use the dishwasher the next time, but only after we force it to go to


While replacing the console board, the replacement should be of same version. The boards are using programmable IC. Hence matching the software version is a must. Only the manufacturer or his authorized provider can help regarding t ... Whirlpool Gold 24 in BuiltIn Dishwasher w Adaptive Wash Cycle 24 in Builtin Dishwasher

Machine Won't Start! I have a KA dishwasher KUDPO2CRBLO and only the "quick clean up" and "rinse only" buttons will light up. Even when they are lit, I hit the "start" button and it will not start. The other cycles won't light at all. Any ideas?


Link for all appliance model numbers.\012Please post your entire model number.\012After you have clicked on the link below....\012Just to the right of the "search" tab click on "help m ... KitchenAid 24 in. KUDP02CR Built-in Dishwasher

My GSX4756 dishwasher seemed to stop mid cycle and the start light is flashing. I have pressed the start button until the light goes out but as soon as I close the door it starts again on the rinse cycle but beeps like it has finished


Did you check to see if anything has fallen down into the drain area. Occasionally a butter knife will fall to the bottom of mine where the drain area is, there's an aparature that spins, and stops the machine midcycle. ... Bauknecht Dishwashers

My Frigidaire Dishwasher FDB1050RES2 gets stuck in a rinse cycle. The light on the front will be lit "clean" but the bottom of the washer is full of water. Opening the door does not turn off the "clean" light. For me to get it to run, I have to unplug it, plug it back in, push the start button until the ?washing? light comes on. I then push the start button once more and the dishwasher will begin to drain. I open the door as soon as I hear the water stop draining into the sink drain. This


By the descrition you are giving you will need to replace the main control board.Part number 154568401.you may also need to check the float switch.The part will run about 110.00 dollars from a local parts store ... Frigidaire 24 in. FDB1050RE Built-in Dishwasher

The dishwasher stops at the rinse cycle, does not drain and then the Quick Rinse button is the only cycle that will light up. Sometimes I can get the washer to choose a different cycle... but it is about every third day. And once the load gets to the rinse cycle, it starts all over again.


... Kenmore 13593 Stainless Steel Built-in Dishwasher

My Jenn Air dishwasher won't start. The cycle lights come on, but the start button will not work. Also, some of the cycle's won't light up. I can only choose some of them, like I can't choose heavy wash or rinse only.


... Jenn-Air Dishwashers

Initially It started washing, completed the entire cycle, then while drying began re-washing the load. Then it would start washing nothing, without any buttons pressed. Then it woldn't allow any buttons to be pressed for any cycle.Then the lights would flash, but nothing would progress through the cycle.


For replacement parts - head on over to PartSelect.com or \015\012RepairClinic.com and enter in your full model number for a full parts \015\012listing.\015\012I recommend both sites because ...\015\012\015\012\015\012FixYa ha ... Whirlpool GU2300XTVQ Builtin Dishwasher

Maytag dw mdb7809awb1 wash cycle and rinse lights work but will not start when I push start button. Where do i begin to check for problem? Thanks


... Maytag MDB7609AWS Builtin Dishwasher

Whirlpool adp 5550 Dishwasher wont complete a cycle. The light in the start button flashes four times in a continuous pattern. Have pressed the start button for 3 -5 seconds to reset after which the machine seems to operate ok then it stops and the start button returns to flashing. Have cleaned the filter and checked the sullage pipe for blockages What do I do next?


... Dishwashers

LG Dishwasher (LDF6920ST) control panel is not working on any other cycle but the delicate cycle. Following power up only one button will light up/can be selected. It started with the normal cycle button going out then the power scrub went out along with the upper rank and rinse only.


... LG Dishwashers

Bosch diswasher Turn dishwasher on lights that are showing are heavy duty wash, sanitize and clean lights. Just beeps like a load is completed - tried reset by holding down start button, etc.. Not able to even change cycles - only button that works is the on/off button


... Bosch SHX3AR75UC Ascenta Series 24 In. Stainless Steel Bar Handle Built-In Dishwasher

I have a Kenmore Type 575-0 Dishwasher, model number 665.16033401, Style 16033. It runs trough the cycle, once the cycle is complete the clean mode light is on but most dishes are still dirty. I had someone here to repair this about a year ago. All he did was press alternating two buttons, which I have tried, it resets and lets you start a new cycle. However, the problem remains. Last time there was only button pressing involved, no need to replace anything. So, I would hate to have to pay ag


You need an electronic control and heating element ... Dishwashers

I have a blinking cancel light on model GU1200xtlt1 and will not start in any cycle. Also if I push another button it flashes rinse button and cancel button. Before this it ran in Sani Clean over and over again and I could not change the cycle. I emptied out a bit of water from the bottom because it did not drain also and the water was not smelling too good.


... Whirlpool Dishwashers

Have a KUDS24SEAL5 superba and no lights come on after pressing any of the buttons. Power to machine is good. Several months ago it would not start properly by pressing 'start'. Would go directly to 'drain' cycle. Then found that if we pressed 'rinse' before 'start' it worked fine. Now, almost a year later...no lights, no one home...any thoughts?


I had a KUDP02CRB and there is a hidden transition connector on the front panel under a black plastic cover that was pulled out a little. It connects the flex cable from the controller board to flex circuit of the panel. I just pushed it back in al ... KitchenAid Dishwashers

We have a Maytag MDBH950AWS Dishwasher that won't start. When you press the start button the cycle light, washing light , heated dry, sanitize and extra rinse lights all come on the dishwasher fills with water and after a couple of minutes it shuts off. Any ideas what is wrong? Thanks


I have Miele incognito that when I shut the door it does not turn on? Not sure why it stopped working all the sudden ... Maytag 24 in. MDBH950AWS Built-in Dishwasher

My GU 120 stops mid cycle and the indicator light starts blinking a humming whirring sound preceeds the ctcle stop nad light blinking. Pressing the button for 5 seconds causes the flashing light to extinguish but the sound continues untill the unit stops. It does not complete the full cycle. Your help would be appreciated. Tony


... Whirlpool Dishwashers

Dishwasher Fault Hi, My dishwasher is a Diplomat ADP8322 (which i think is a rebadged whirlpool unit) & has been playing up recently. When you start a cycle it is fine for a minute or so then it starts beeping, the rinse light comes on & the light next to the start button flashes 11 times, pauses then repeats. I have read online that this flashing relates to what the fault is, but i cannot find out what fault the 11 flashes relate to. The first time this happened i cleaned out all of the filters


... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1762 seconds