Having problems with your Maytag MDB5100A Dishwasher ?

Maytag dishwasher, control panel is dead, has power to board,but there are no lights on the panel when you close the door, like it normally would. any ideas I replaced the board with no succes. thanks Bruce, B&L Appliance


Answers :

I think you have diag your problem . your have power to the board . so the inter lock switches are ok . and no lights . if you look at the printed pc board i think yoy may be able to see that one or more soder joints have failed . best to change board ant this will correct problem. pt # 99002832 ( 123.89 ) . hope this has helped mm and thanks for using fix-ya .. mm
Repair Help & Product Troubleshooting for Maytag MDB5100A Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Maytag dishwasher, control panel is dead, has power to board,but there are no lights on the panel when you close the door, like it normally would. any ideas I replaced the board with no succes. thanks Bruce, B&L Appliance


I think you have diag your problem . your have power to the board . so the inter lock switches are ok . and no lights . if you look at the printed pc board i think yoy may be able to see that one or more ... Maytag MDB5100A Dishwasher

Maytag model MDB5600AWB replaced faulty control panel started and lit up like it is supposed to do started wash with glisten cleaner and when I tried to cancel drying cycle panel or board would not respond, waited till unit was finished and control panel blinked and went dark , bad control board?


... Maytag 24 in. MDB5651A Built-in Dishwasher

I have a MDB6759AWS3 that is one year and two months old. This morning I went to the control panel to press the buttons and some would light up and others would not. I disassembled the inner panel and looked at the "computer like" flat ribbon that connects the control panel to the main circuit board and noticed that some of the wires in the flat ribbon had deteriorated. I put it back together and pressed the buttons and they flash very dimly for a few seconds and got the dishwasher working bu


You may want to check the warranty iif it is a maytag or whirlpool, some have a 5 year warranty on the control and board. If not you can go to www.searspartsdirect.com to l ... Dishwashers

I have a frigidaire dishwasher model FDBC45BAB0. It has a black door (full door, not panel). I would like to either replace entire door panel w/stainless. Or get a stainless panel just for the front. Any ideas? Thanx


Hello! Here is a website that offers a selection of stainless door covers........www.kitchensource.com/kau/frigodw.htmGuru...................saailer ... Frigidaire 24 in. FDB1050REC Stainless Steel Built-in Dishwasher

A few days ago the dish washer was running fine, maybe a single wash every day. Then, out of no were the logic seems to have left the machine. If you pressed the "normal cycle" button it would blink for about 30 to 45 seconds then the front panel would go blank. All LED lights would turn off, like it finished doing the diskes, never running a single cycle. I unplugged the machine to let all circuits reset, that worked for two days, two washes in that time. Today I'm back to a machine that will n


Your control panel is faulty and will have to be replaced. This is the main brain of the machine. Normally when a cycle doesn't start the timer is bad, but when your control panel doesn't do anything, then it is faulty. ... Dishwashers

My Frigidaire fghd2433kf1 starting flashing PF occasionally. I would open and close the door and it would go away. It became more frequent until two days ago when the dishwasher stopped mid cycle and flashed PF. When I opened and closed the door, everything went dead and the dishwasher no longer works. It acts like it has no power coming into it. I checked the breakers and the wires connecting the power into the dishwasher. No luck. I replaced the control panel, but not the control board. It did


... Frigidaire FGHD2433KF Builtin Dishwasher

Zanussi zdt6053 in built dishwasher not starting. When pressing the control panel on/off button the 65 deg normal wash light comes on. When pressing the program selection button nothing happens. When closing the door the machine does not start up. Is there a fault in the control panel circuit board? Would water pressure prevent the machine from operating?


... Zanussi 23 in. ZDi6053SX Built-in Dishwasher

Continuous running I have taken on board solutions already published on the site re possible controll panel damage etc. But I would like to check that the waste water pump isn't blocked before dismantling the controll panel. Could you describe how to access the pump to check it out. Thanks Rogspeed


... Bosch 22 in. SKT5108 Free-standing Dishwasher

I would like to get stainless panels and I am not sure if they make them for the GE Nautilus 24" dishwasher. any ideas of where and what I can do?


Absolutely...\012Go to www.applianceart.com\012\012These guys make stainless panels cut to your measurements.\012 ... GE Nautilus 24" Built-in Dishwasher

The normal light is flashing on the panel but unit will not run. I tried a new control board and bi-metal fuse. The light is still flashing and dishwasher will not do anything. Kitchenaid model kud1021rbso. Any help would be greatly appreciated.


... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

Bosch Dishwasher hi, was thinking of buying a second hand bosch aquasensor dishwasher.. I think the model is Bosch SGS46M78AU.. anyhow thw current owner says it needs 'minor electrical repair to circuit board' and when queried further said that sometimes it washed in normal time and at other times it took up to two hours. Any idea what the prob could be, and would it be costly to fix?? Thanks!


The circut board is very costly stay away from that one ... Dishwashers

Hi, I have a KitchenAid Model: KUDP02FRSS1. I push start/resume (it blinks) and am given the normal cycle with heated dry, or rinse only as my options. No other buttons work. Also, soap tray does not open during cycle. I replaced circuit board #8559825 to no avail. Is problem likely the control panel?


Control panel is the most likely the cause of your problem. A faulty door switch may also cause this. ... KitchenAid 24 in. KUDP02FRSS Stainless Steel Built-in Dishwasher

Unable to start dishwasher, only functioning light on the panel is the cancel/drain light. push that button the machine funtions for a minute or two and shuts off,also the light above normal wash is blinking. When the machine last functioned it would start with a very high decibel level.If its the circuit board I need an approximate replacement cost. Bob


If you go to searspartsdirect.com you can get the exact cost of the module. ... Dishwashers

I have a Fisher and Paykel drawer dishwasher and I'm wondering if there's a way to put a panel on it to make it look like and integrated dishwasher. It would need some way of the panel moving to start the dishwasher because the controls are located on the front. I plan on putting it in an Ikea Akurum that is 24" deep. The dishwasher is 22-9/10 deep, so that looks like it would leave some space for the dishwasher to sit back in the cabinet so the door panel could be flush with the cabinet. I'm no


Hmmmm...the first thing that comes to mind is to check out ApplianceArt.com. they have alot of panel options. I'm not sure if they have the integrated ones you are looking for but they have cheap options for everything else. ... Fisher and Paykel 24 in. DD603H W Built-in Dishwasher

My Whirlpool Gold Quiet Partner III dishwasher will not start. I have installed a replacement control board that worked for awhile. When it quit I put the old control board back and it worked for awhile with a portion of the lights on the control panel lighting up. After switching control boards back and forth, it will not work at all now. It will run through the diagnostic program (Normal, Heated Dry, Normal, Heated Dry) but after that the start button plus other buttons are not lit so it will


... Whirlpool 24 in. GU2500 XTP Built-in Dishwasher

My accusense light keeps coming on and blinks continuously. I tried the heat-dry, normal sequence and it would reset to 2 minutes. After the 2 minutes cycle, the accusensor blinking would begin again. Then I tried holding the heat-dry button in for 5-seconds. This looked like it worked so we set a normal cycle without heat-dry. Äll looked good, but a few minutes in, the normal light was off, the accusensor was blinking again and the heated-dry was on again! Is the unit possessed? Other id


... Whirlpool GU2400XTP Built-in Dishwasher

I have a Maytag QuietSeries 300 dishwasher. My original problem was with the control panel lights not coming on. Another repair website recommended replacing the circuit board. We replaced the board, but it did not solve the problem & the dishwasher would not work. Replaced the control panel. Lights come on, but when the start button is pushed "21" flashes on the time display. What do I do?


HI,Just visit this link HERE and your problem will be solved.Goodluck,Please don't forget to rate the solution. ... Dishwashers

In December 2010, I purchased an Electrolux range, microwave and dishwaser for my kitchen. Already I have had to replace the computer boards on my all three appliances. Last night, I load the dishwasher and go to turn on and the computer board is dead again. What is the problem and would you advise that I return all 3 appliances for a refund?


... Electrolux EWDW6505GS Fully Integrated Dishwasher with 9 Wash Cycles, Nylon Racks, Wave-Touch Contro... 24 in. Built-in Dishwasher

I have a Kenmore undercounter dishwasher..model 665.16022400. The "normal wash" light keeps blinking..nothing will work on it..I tried reseting didn't work, killed the breaker for a while, didn't work. I tool the panel off and reseated the ribbon connection to the electronic board..didn't work. I'm not sure if I should be replacing the electronic board, or the control panel that contains the buttons. None of the buttons appear to be stuck. thanks - Andrew


Hi,This is a common problem. As i cannot diagnose the machine myself, it would be tough to exactly comment on the fault. However, more often it is an issue with control panel keypad assembly.You need to replace that.Let me kno ... Kenmore 16024 Built-in Dishwasher

I have an MDB6701AWS3, The buttons on the panel stop working. I see that the ribbon that connects to the control board has a brown tar like substance on it, or it could burned. How likely is this my problem, instead of the control board? Thank You


... Maytag Dishwashers

Hobart LXi Dishwasher stops and starts in the wash cycle. Sounds like it's trying to 'start up' (like a lawn mower with a pull string). Sometimes, will run fine. Almost like a 'short' or something. Control board wash light clicks on and off. Any ideas?


... Hobart Undercounter/Lxi Warewasher 24"W x 26-3/4"D x 33-3/4"H With Detergent Pump, Hobart

I own a KUDS01FLSS3 KitchenAid dishwasher. The lights on the control panel do not come on and a cycle can not be started. There is about an inch of water in the bottom of the dishwasher basin and it looks like the previous cycle did not complete. I have checked the wall outlet that the washer is plugged into and the washer is receiving power from the wall. And ideas? My next thought was to take the door off and check the power supply running to the door panel and control panel.


Servtek06 writes:\015\012check connections @ control board/module. May be Control Board/Module. ... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

Ariston LSI 41 dish washer had intermitant problem of green light not coming on when main power switch turned on and machine not working, the circuit had beed repair before. I played around and got the machine to go through a full circle once then would not go again. So I have put a new circuit board with switch etc. still the switch panel light dose not come on, i found bad connection in connector which comes from small plug on circuit board, (two red wires )I have checked for power to board. W


... Ariston Technologies Dishwashers

Diswasher A couple of days ago my dishwasher would not start, there are lights on the front panel and it starts a washing programme but doesn't actually wash anything. I removed the filter from inside the dishwasher and it is full with water, it seems like there is a blokage somewhere. Would a blockage cause the diswasher not to start. Any help on this problem would be greatly appreciated.


Jhgf ... Whirlpool 24 in. ADP6940 Dishwasher

I would like to know if a replacement panel available


... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0868 seconds