Having problems with your Maytag MDB7100AWB Dishwasher ?

Maytag MDB7130AWB dishwasher blows circit breaker.

\015 I ahve a Maytage MDB7130AWB dishewasher that sometimes blows the circit breaker. It is 7 years old and has been doing this for a few monthes. Sometimes it runs a full wash cycle fine, the next time tou have to reset the circit breaker 4 or 5 times to fet a full wash cycle. I have looked for pinched or cut wiring but have found nothing wrong. Any help or ideas would be great. An electrical diagram may help too.\015

Answers :

These have been known to leak water into the door panel. If so the water can cause a short. Your breaker is keeping the machine from lighting up. Check any seals that may have been braeched in the door. Start at the dispencer latch
\015\012rubber.
Repair Help & Product Troubleshooting for Maytag MDB7100AWB Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Maytag MDB7130AWB dishwasher blows circit breaker.


These have been known to leak water into the door panel. If so the water can cause a short. Your breaker is keeping the machine from lighting up. Check any seals that may have been braeched in the door. Start at the dispencer latch \015\012rubb ... Maytag MDB7100AWB Dishwasher

My dishwasher so my dishwasher seemed to have quitworking during a cycle. like breaker triped or something. i checked the breaker and thats fine. it seams like its hard wired in though. Would that be right? and is there a fuse or something that could/would blow during a wash? I dont know what model it is or anything it was in the house when i got it. The dishwasher is built in and it seems decently old its a kenmore ultra wash and it has like 10 buttons for the differend cycles on the left and a


Sounds like the fuse on the control blew. you can replace the fuse for\015\012around $20 or you can cut and splice the wires for free. If that doesnt\015\012work then you may have a loose conection in your junction box under the\015\012dishwasher. ... Kenmore 24 in. 15932 Built-in Dishwasher

The contol lock LED is illuminated on the front panel of my Maytag dishwasher. (Neither my wife nor I pressed the control lock for 3 seconds!) We've tried to extinguish it by pressing it for 3 to 5 seconds, but it remains ON. We've turned off the breaker to the dishwasher overnight, but when we turn the breaker back On, the contol lock LED comes on. We simply can't unlock the control panel. We can tell that all of the other buttons work just fine because pressing any of them causes the 3 Sec LED


If by pressing the control lock button for 3 seconds does not solves the problem.then there are 3 possibilities due to which this problem may occur\015\0121)the door is not closing properly. the dishwasher door latch is either cracked internally or t ... Maytag Dishwashers

Disposal plugged up and water backed up into dishwasher. Cleared disposal and dishwasher drain line. Checked around sump but dishwasher won't pump out. Sounds like pump is trying to run. I can blow air through the drain hose from the disposal and get bubbles in the water. Turned off breaker for 1 min. then tried reset. Can hear pump humming.


The pump is humming because its still trying to get all the water out of the unit. Deinstall the dishwasher and pull the entire dishwasher out from under your cabinet. Next step would be to disconnect the drain line from the drain pump and check to ... Dishwashers

Dishwasher blows circut breaker and shuts down about 5 minutes into cycle.


Possibly your heater is shorting. ... Bosch 24 in. SHE44C02UC / SHE44C06UC / SHE44C07UC Built-in Dishwasher

My Smeg DWF612SS dishwasher blows circuit breaker


... Smeg 24 in. DWF612SS Free-standing Dishwasher

Maytag dishwasher mde8600aww I just replaced dishwasher handle and switch assembly and turned power on at breaker and lights blink independantly like its in diagnostic mode. customer said it started doing this last night? I have no tech sheet or manual 4 this. Help


Hi\015\012\015\012\015\012Thanks for using FixYa. The model no# mde8600aww for your Maytag seems to be a model no# for a Dryer instead of a Dishwasher. However, from what you have described it seems it is the control pa ... Dishwashers

Dishwasher won't blow dry dishes - Maytag Dishwashers


... Maytag Dishwashers

Maytag MDBH970AWS Heating element won't turn off. Dishwasher heating element won't turn off. Have to shut off the breaker to make it cool down. Heating element gets hot as soon as you flip the breaker back on


The heater relay is located on the control board, a faulty relay or a faulty control board would cause the problem you have described. The fix is to replace the control board. Parts for your unit should be available from most appliance parts retail ... Maytag 24 in. MDBH970AWS Built-in Dishwasher

Have a Maytag dishwasher that will not run, display panel just has three blinking lights. Have turned off circuit breaker trying to reset dishwasher, to no avail. Still blinking.


Behind the lights and the control buttons there is a central control circuit board (known as the CCU), this board is going to need to be replaced, the part price depends on the model number of the dish washer, but on a ... Maytag Dishwashers

Start button flashes 2hr, but will not start the dishwasher, when touched. Also, lights on top of the door are not always functioning. I phoned Maytag and customer service had me turn off the circuit breaker for 5 minutes. This did not change the dishwasher. I think that the door latch is not snapping into position, when I open the door.


... Maytag 24 in. MDB7601A Free-Standing Dishwasher

Maytag MDBH979AWS dishwasher - there appears to be no power coming in to it. The dishwasher will not turn on and there are no lights on the control panel. I checked the power in the breaker box and it works fine. Any suggestions what to do next?


Maytag MDBH979 power sensor will not turn on dishwasher. The other buttons and lights turn on when pressed but not the power button. Please help. ... Whirlpool MDBH979AWS Builtin Dishwasher

I have a 4 year old Maytag MDBH945AWW and the panel lights come on and I can select cycles... but the dishwasher wont start. I tried holding the start cancel button, tried turning the breaker off for a couple of hours, took the inner panel off the door and checked the latch, but its still wont start. Any other suggestions? If it needs a new control panel its probably better to just get a new similar dishwasher for $300, correct?


What you need to do is read for continuity and power across the door latch switch. (2 white wires) AND 2 Black wires Both wires must read continuty at the control panel connectors to the power source terminals for the unit to start. Since the co ... Maytag MDBH945AWW / MDBH945AWQ / MDBH945AWB Built-in Dishwasher

I have a aeg 43070 vi dishwasher It keeps tripping the circit breaker on the house fuse box . I have reset the leak cutout by dipping the dishwasher back and stopped the warning sound,but went for about a minute and then trip the electrics again . any ideas whats wrong ?


I assume you are refering to the earth leakage circuit breaker. This trips when a earth leak fault has occured. The normal cause for this could be\015\012A) Water leaking via a pipe at the bottom comming in contact with one of the electric moto ... AEG 23 in. Favorit 44070Vi Built-in Dishwasher

MDBH945AWW maytag dishwasher panel lights will not light up. checked breaker and was not tripped. Hardwired circuit. will check tomorrow to be sure power gets to dishwasher. Suspect have panel control failure. In which case should I box it up for the local dump.


These control boards do not have fuses on them. I opened mine up when the front panel touch pad stopped working and the LED indicators were anemic. This is a sign of the ribbon cable connections have oxidized. The ribbon cable connects the touch p ... Maytag MDBH945AWW / MDBH945AWQ / MDBH945AWB Built-in Dishwasher

My Maytag dishwasher model MDB600AWB, serial 18721619CN Quiet Series 300 will light up on the panel except for NORMAL WASH and START. It will not run. All other buttons work. It displayed the number 9 and the RINSE ONLY light came on after we got off the phone with Maytag. Initially nothing would light at all. We changed the fuse (it is NOT on a breaker) and it again didn't light. A few minutes later it did light the above mentioned buttons.


... Maytag Dishwashers

The maytag dishwasher model mdb7130AWB stoped cleaning correctly so we went from the arm assembly in bottom of dishwasher down to the cutter disc and we found a crack in the housing so i ordered that piece. the new part was designed a little different but we put it all back together the way it came off. but it started and ran maybe 1 minute and stopped. so i have pulled up the diagram and see some problems. in the current diagram. original there was no part 37, 17 19 and 3, alos the crew d


... Maytag MDB7130 Dishwasher

My Maytag dishwasher stopped working during a cycle. It looks like an electrical problem. I checked the breaker and looks OK. Looks like no power is getting to the dishwasher. Can you help ?


Your maytag dishwasher should hav a free inhome service\015\012\015\012http://www.bobvila.com/OnTheLevel/Maytag-Dishwasher-Reca ... Dishwashers

Maytag dishwasher model mdb9100aww will not turn on I checked and reset the breaker and also checked to see if any wires were loose


Did you check the door lock mechanism? if it is not locking the door properly, the machine will register an unlocked door situation and will not start. ... Maytag MDB9100A Dishwasher

Cannot get Maytag Jetclean Dishwasher-Quiet Plus will not start at all. Push the buttons and get nothing. The circuit breaker is not tripped. Is there a reset button or something like that.


... Maytag Dishwashers

My Maytag MDB7130AWB dishwasher is leaving detergent residue on the dishes. I removed the lower spray arm and filter screen. The screen was very clean with no mineral build-up. What could the problem be?


This is going to be more of a problem as the dishwasher detergent manufacturers are removing phosphates from dishwasher detergents. You can buy phosphates (or STTP) from various sources on the internet. It's called Sodium Tripolyphosphate. It's about ... Maytag Dishwashers

I have a Maytag Quietseries 300 dishwasher that I bought new in 2004. The buttons on the control panel will not respond. That is, no lights will display when I push the buttons. It has behaved like this in the past and after several weeks of not using it suddenly it will begin working normally again. However, I think this time it has stopped working permanently. The model number is MDBTT79AWW. What do you think could be wrong? I have tried flipping the circuit breaker to reset it but no c


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks for using FixYa. It seems to be the ... Dishwashers

How to reset dishwasher maytag MDB9601AWB? Tried depressing the button for 3-5 seconds the way the manual says - no good. "Lock" light just stays on. Tried unplugging. No good. Tried circuit breaker. No good.


Let the breaker sit off for an hour, if that does not work it needs help ... Maytag Jetclean III MDB9601AWW / MDB9601AWB Built-in Dishwasher

Hello there from New Orleans!! I really could use some help. I have a Maytag mdb8951aws dishwasher that I purchased in 06 for 795 bucks, plus 180 for a 3 year warranty!! They came out maybe in 07 becaise of some recall, I don't remember what for. I called them because my heater stayed on all day yesterday and melted some dishes. Good thing we caught it last night and shut off the breaker. They said it was not recalled and out of warranty. Go figure! Do you know what this might be and how


It sounds like your heating element shorted out, causing the heater to stay on. You can replace this yourself, very easy to do. You should be able to buy this part on line. ... Dishwashers

Dishwasher blows breaker just sitting there off.


Are you sure the unit is off ?If you have unplugged the unit and no breaker tripping occurs and tripps when machine is plugged in but switched off chances are you plug socket(on the wall) is the culpret here in which case I suggest you get a qu ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1493 seconds