Having problems with your Maytag MDB7100AWB Dishwasher ?

NO POWER TO THE DOOR PANEL

\015 I have power to my dishwasher but nothing on the door panel will work. It doesn't even ligth up.\015

Answers :

Check door switches at door latch
Repair Help & Product Troubleshooting for Maytag MDB7100AWB Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Have a GE Quiet Power 3 Dishwasher. Went to reun it and when I closed the door no lights came on to pick a wash cycle. Nothing like it lost power. No buttons work, nothing. Opened door and removed inside door panel. Have power at door latch switch. Actually have power at all 4 connections and doesn't change when engaging switch as if door was closed. Switch does click but no power at front control panel. Whats up. I have my own Handyman/Home Remodeling business and I'm very good at fixing things


If your dishwasher is not running check the following \015\012\015\012You have already taken care of the 1st item.Power Supply The main power supply is the first thing to check. Also remove the toe ki ... Dishwashers

Quit working during wash cycle, about 6 liters of water left in bottom, looks like it quit during rinse cycle. There is power to the door switch and door switch works shutting off power when door is opened. However the control panel does not respond to any push button. I have had a problem in the past with moisture from the door vent getting into the control panel area causing the push buttons to become eratic.


The capacitors in the control panel could be bad or have burnt out. Do check all connnections and if necessary, check the continuity of the power to and from the control panel with an ohm/voltmeter. ... Dishwashers

I own a KUDS01FLSS3 KitchenAid dishwasher. The lights on the control panel do not come on and a cycle can not be started. There is about an inch of water in the bottom of the dishwasher basin and it looks like the previous cycle did not complete. I have checked the wall outlet that the washer is plugged into and the washer is receiving power from the wall. And ideas? My next thought was to take the door off and check the power supply running to the door panel and control panel.


Servtek06 writes:\015\012check connections @ control board/module. May be Control Board/Module. ... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

Continuous alarm after a power failure an alarm started going off in the door of the dishwasher. the push button panel is not functioning. I opened the door panel and found an electronic control circuit board. It is this board that is making the noise. I unplugged the black and white pair of wires on the lower right side of the board and the noise stopped. this must supply power to board. Anyone know what this problem is?


I posted this under "Ben's" problem as well, but I had the exact same problem. I know which black and white wires you're talking about. I don't know what causes this, but getting new parts did fix it. The black box that all those wires go into on ... GE 24 in. Profile PDW9880JSS Built-in Dishwasher

I have a Magtag dishwasher, model #MDB6650AWQ thats not running. I check the power supply all the way up to the door latch and it shows that there's power there. However the circuit panel not lighting up and nothing happens when you push the normal wash cycle or any of the other buttons. I believe the problems is electrical in the door latch handle. Is there any way to check the solenoids which are attached to the door handle before I order a new door latch.


I have the same problem with mine. It is 3 1/2 years old. The repair man was just here and said it is the control panel. It will cost $171.85 for the part and then $53.85 today for his visit and then a return visit when the part is in.\015\0 ... Maytag Dishwashers

I have a Maytag MDB5601AWB dishwasher. all the switches except the heated dry switch are not working. I did the unlock thing and still nothing . Do I need to replace the switch panel or is there something I should try? I tested for power and have 120 volts coming into the circut board and through the door switch Comments: Aug 22, 2009 - I tested the door swich and I have power on both poles when it is closed. there is 2 switches on the latch but the one with power to it powers up the circ


... Maytag 24 in. MDB5600A Jetclean II Built-in Dishwasher

I have power to the unit but there are no lights on door when closed. Unit will not respond to any buttons and lock not on.I have opened up the door panel and have power to the door switch and then to the board.What is my next thing to check?


Ok so you have power going to the unit at the bottom if the unit is not under warranty? first are any LEDs operating at all when door is opened? if not you most likely have a control issue to test this you would remove the screws along both sides of ... KitchenAid 24 in. KUDI02IR Built-in Dishwasher

My Kitchenaid dishwasher KUDIO1FLSS1 stopped during the wash cycle. No lights and no power. I checked the power to the washer and the fuse inside the door panel. Both fine.


... KitchenAid Dishwashers

I have a Whirlpool Gold Quietwash Plus (part # 9744480), due to a number of opening and closings of the door, the lights on the front panel now just blink. How can I reset the control panel.. I have tried power scour>air dry>power scour>air dry and only end up with both blinking instead of going into control diagnostics by pushing pots&pans. The unit will attempt to start then just go to blinking lights.. Thanks


I would cut the power to it for awile 5mi and try it that may do it ... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

Maytag MDBtt60awb will not start. Power definitely at dishwasher as panel lights are on, however "start" button does nothing. Dishwasher is less than 2 years old. The panel buttons eventually turn off. I've cycled the power to the unit with no response. The door is definitely latched. Unit ran fine a few days ago.


Most likely you have a bad motor when replacing the motor ihave found it is cheaper to get the pump with the motor attached where as they charge you more money for just the motor or the pump seprately try allbrands appliance parts they seem to be che ... Maytag 24 in. MDB5600A Jetclean II Built-in Dishwasher

My Frigidaire fghd2433kf1 starting flashing PF occasionally. I would open and close the door and it would go away. It became more frequent until two days ago when the dishwasher stopped mid cycle and flashed PF. When I opened and closed the door, everything went dead and the dishwasher no longer works. It acts like it has no power coming into it. I checked the breakers and the wires connecting the power into the dishwasher. No luck. I replaced the control panel, but not the control board. It did


... Frigidaire FGHD2433KF Builtin Dishwasher

WP DW Mod # GU1200XTLS0: this unit filled with water and just stopped running. I have power to the unit. The control panel does not light up at all. Its wierd that I have power to the board and all the wires seem to have power! No burnt spots and no burnt smell on the board.Hmmm! Door latch and switches all check ok. Oddly it seems like the line power to DW goes all the way thru the unit and back through the nutural wire. Could the motor windings be burnt out?


Hello , there should be a fuse located by or on the side of the board with 2 wires going to it , one from the latch and one from the board ,it does come off , use an ohm meter to check it , it should ohm out or have low resistance make sure to take t ... Whirlpool GU1200XTLS Stainless Steel Dishwasher

I have a GE Quiet Power 3 built in dishwasher. With 1 min. left in a cycle, I opened the door, removed an item, then closed the door again, but it didn't finish the cycle. The machine continued its single beeps to indicate the door was open. Reopened and closed the door. None of the buttons on the control panel respond. Have unplugged and left overnight, plugged back in, beeping continues.


... GE 24 in. GLD6500L Built-in Dishwasher

NO POWER TO THE DOOR PANEL


Check door switches at door latch ... Maytag MDB7100AWB Dishwasher

No power unit went dead checked power to base of unit ok also shut off breaker for 10 minutes to see if it will reset, no luck. Also removed inner door panel to reveal circut board to look for a reset or small fuse, none evident.


... General Electric GLD5960NSS Stainless Steel Built-in Dishwasher

Kenmore elite clean lite is flashing won't shut off.unit won't work modle #66516912001 serial#fk4402228.it flashes 7 times over and over.i shut off all power turn back on still flashes .i replaced electric board in door panel new button panel


I have a service bulliten on this if you will email me at [email protected] ill send it to you its too big for here ... Dishwashers

GU1500XTLS3 Periodically won't start. Dishwasher has power because pressing cancel causes dishwasher to start draining (even though there is no water). Door switch works because opening door prevents starting drain cycle. No other button on control panel will work except for the 'air dry' / 'lockout' button. Turning off circuit breaker for 15-30 minutes and then turning circuit breaker back on seems to fix the problems but only for a couple uses and then it stops working again. Need ad


This could be the 'fill switch', which is the level sensor. Could be a plastic tube that exerts air pressure into the tube as it fills, make sure it's clear and open. The dishwasher has a sensor that monitors the door being closed too. Some use a hig ... Dishwashers

My Bosch SHE98M will not respond to pushing the Cleartouch buttons. It is just stuck displaying the normal wash. It will not respond to pressing any of the touchpads. When the door is closed it displays "not started". I have powered the unit down by switching it off at the supply, then restoring power but there is no change. It appears as if the cleartouch panel is no longer sensitive to touch?


... Bosch Evolution 800 SHE98M05UC Stainless Steel Dishwasher

I have a Kitchenaid model KUDL02IRBS1 dishwasher. It died with no lights to the front panel at all. I have power at the main wire connection to the unit. I checked the door switch and it works. I checked power at what looks like a solinoid on the circut board and it has 115V.


... KitchenAid 24 in. KUDI02IRBS Stainless Steel Built-in Dishwasher

Maytag dishwasher, control panel is dead, has power to board,but there are no lights on the panel when you close the door, like it normally would. any ideas I replaced the board with no succes. thanks Bruce, B&L Appliance


I think you have diag your problem . your have power to the board . so the inter lock switches are ok . and no lights . if you look at the printed pc board i think yoy may be able to see that one or more ... Maytag MDB5100A Dishwasher

When door is secure and power active, nothing happens when I try to select a cycle via the door panel. Any ideas?


... Maytag 24 in. MDBS561A Built-in Dishwasher

The control panel on my Maytag MDBH970AW is unresponsive, and the latch is stuck in the "open" position (the plastic piece stays pushed in to the handle and won't come down). I've checked that the unit is getting power from the house. Last time I had this exact problem (when it was under warranty), they had to replace the control panel, the latch, and it seemed like most of the door. What should I do?


... Maytag 24 in. MDBH970AWS Built-in Dishwasher

The electronic panel on the top of the door doesnt light up anymore and is unresponsive, when the power is turned on, the machine makes a sound like its running or draining or something, but nothing is happening. This all started after a potential electrical disruption following a power outage. Perhaps there is a fuse or some relatively easy way to fix this? or am I screwed and should just call a repair man. Thanks for your suggestions, Brodie


... Bosch 24 in. SHX56B05 Stainless Steel Built-in Dishwasher

Quick Rinse light was flashing at end of cycle. Opened and closed door and pushed Start. Quick Rinse and Cancel/Drain light are now flashing and machine won't start. Turned off power supply (30 seconds) / turned on power supply and then tried again to start the dishwasher, but same problem. Control panel seems to be frozen at the Quick Rinse/Drain mode and will not cancel. Help! Thank you


Ok try this, open the door and then hit these buttons in the following combination. HI TEMP - DRY - HI TEMP - DRY...then close door and press cancel...then wait for the pump to shut down. you should be able to run a cycle after this...If this fails ... Dishwashers

Came home and dishwasher was stil running from the morning. Opened the door and all the lights on the control panel were lit up and unresponsive. cut power to unit for 1 min and now the controls don;t light or respond to anything . They are not locked and there is power to the unit any ideas ?


Hi\015\012\015\012\015\012Thanks for using FixYa. From what you have described it seems that the control panel has gone bad and needs to be replaced however, if you want more information then please do revert with the manufac ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1047 seconds