Having problems with your Maytag MDB8601AWB Built-in Dishwasher ?

Can't get unit to start.I have power to unit.

\015 Found water in dishwasher from last cycle and touch pads won't work.\015

Answers :

Some open the door in mid cycle ? Try shutting the breaker off and restart the unit.
Repair Help & Product Troubleshooting for Maytag MDB8601AWB Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

No power My dishwasher Model DMR77 quit working yesterday during a wash cycle. No power ie, no display light or tones. I am getting power to the unit, checked with a volt meter. I am thinking Power supply, or is there a reset on the unit.


Hi,\015\012 The main PSU is part of the control board. You may be lucky to find an aged fuse to replace, but it's more likely a power transistor that's fried.\015\012\015\012Unplug and remove the control board to see which bit's toa ... Samsung DMR77LHS Tall Tub Dishwasher

Unit does not power up. checked power to unit ok checked power to latch switch - ok appears circuit board is bad. Traced 120v to board. Any other checks before getting new dishwasher?


Hi mgray770,\015\012It sound like you have done a good job already, but just a couple thoughts before you go buy a new one. If the board does nothing then it could be locked, check your owners manual or whirlpool.com for the exact unlock inst ... Whirlpool Dishwashers

Kenmore 13599K600 stopped working. Panel board doesn't respond - no lights, no response. Power getting to unit... checked at hard wire ends behind kick plate panel and power is reaching the unit.


Had the same issue and had to replace both the board and the fuse. Six months later, same issue again. It might be when the "Sani Rinse" is used as it dies at the end with some water left but the water is very clean. Possible defect? ... Kenmore 13599 / 13594 / 13592 Built-in Dishwasher

I have a Whirlpool Gold Quit Partner III, model GU1100XTLB1. When I run the normal cycle it functions well until near the end. At that time the unit stops and the pots&pans indicator light blinks. If I hold the cancel button in the unit drains then refills and the light starts to link again. I don't know how to reset this unit because I only have air dry. If I leave the power off for a day I can get the unit to reset. If not, it just fills back up with water and the pots&pans starts blinking aga


... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

My hotpoint hda3220z07bb has no power at all , turning the timer dial gets no response at all, but I do have power to the motor, water inlet and the interlock works fine, the unit appears dead but there's power there.


CHECK DOOR LATCH OR TIMER BAD ... Hotpoint 24 in. HDA3400G Built-in Dishwasher

An electrical panel breaker switch was replaced after the microwave and dishwasher both lost power. The microwave works after replacing the main panel breaker. However the dishwasher will not show any power. Checked the internal circuit board, no burned areas, cannot find an internal GFI reset, what can I do to get power restored to the main control panel or even the unit itself? Rick C


1)check any fuse in the circut board.(blown off)\015\0122)check any loose connection of neutral (or)phase wire to the machine(or)in the switch. ... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

No Power I have a bosch shx33 dishwasher. I just replaced the water valve because of a leak and now I can't start the dishwasher. It's like there is no power to the unit. I know there is power because I get a shock if I touch the two wires that are connected to the water valve. Is there another trip switch or something somewhere?


First let me say that using parts of your body to test for mains electriciy is a VERY VERY bad idea. You are lucky you are not dead. Please do not touch live parts again, get a multimeter or a mains tester.\015\012\015\012If there is mains across the ... Bosch 24 in. SHX33A02 / SHX33A06 Free-standing Dishwasher

The power went out and we cant use the reset button to get the alarm to go off. The error says 8. When the power went off it was not washing dishes and the door was not locked. Dish washer Model KDS-17A Thanks, Todd


I would try unplugging it for 30 minutes .. ... KitchenAid Dishwashers

Cant get the front door open on my kuds25sh no way to get at the screws that secure the unit to the counter i am very good with tools but i dont know the way the mechanism is set up please help my wife is driving me crazy cliff


... KitchenAid KUDR25 Dishwasher

Installed an older model dishwasher for a friend power works oes throuth the cycles but its not pumping water into the uniT there is no clogs and i hear the pump turn on. unsure why its not getting water into the unit another friend thinks its cause the air tube isnt hooked up but i think it may be something more then that any ideas


You will need to disassemble the bottom part where the bottom rotary spray nozzle is(the part that shoots water upwards). The impeller might have come loose or it is clogged in that area. ... Hotpoint Dishwashers

I have a Kitchenaid KUDIO1DL white dishwasher which is a few years old now but has worked great since I bought it. Today it has the lean light flashing and will not turn on. there is power, and the drain button seems to work, but I can not get the cycles to come on. When I press the start button, I just get two dash lines and then the unit turns off. Thanks


... KitchenAid 24 in. KUDI01DL - Multiple Color Built-in Dishwasher

Hi, Had a power cut at my home and my Caple Di455DL Dishwasher was mid cycle on a glasswash program at the time, since power has been regained it will not restart or reset itself, it just lets a pulse of four beeps go once the door is shut and makes a sounds like its trying to pump out water? tried turning off at mains etc but cant get it to reset!


... Dishwashers

Whirlpool DU927QWDG1 Hi, The problem I'm having with my dishwasher pertains to the door cover for the area I place the soap. There is a small spring which helps the door pop open to release the soap when washing. I cant figure out how to place the spring so that the pops open.....right now when I run the unit the door stays latched and the soap doesn't get dispensed. Any ideas on how to repair this or where I could maybe get a parts manual??? Your expertise will be greatly appreciated!!!!


... Whirlpool GU2400XTP Built-in Dishwasher

We have a 6 year old Jenn Air dishwasher model JDB2150AWP We had a cracked door close unit which we replaced but got a short while restoring connections I am wondering if there is an internal circuit breaker, relay or fuse on these machines that we need to check and possibly replace since we cannot get it to run at all. No power or lights at all. I believe all connections are secure and we replaced the door close unit with new parts.


... Jenn-Air 24 in. JDB2150AWP Built-in Dishwasher

My Kenmore Ultra Wash Dishwasher model 17731 stopped working mid wash I checked the power cord and it is fine but the unit doesn't seem to be getting power. Is there a fuse in this thing? Any advice would be welcome.


... Kenmore Dishwashers

Hobart commercial under the counter diswasher LXIC Model Number 130016. DELIME light comes on every day at startup. Machine will immediatly run (in DELIME mode I think) for about 5-10 min and then get E4 error. We unplug power to the unit let it set, replug it back in after 3-4 cycles of this, it will eventually work perfect for the entire day. I have replaced the Sensor that is on bottom front of the unit in the water trough. ( I replace the sensor to the right if you are looking at the un


Q have your run a descaler . to rid the machine of its deposits . in order for the machine to run properly the parts and pump / screens must be clean . / descaling for deliming . dishwasher and icemakers is comm ... Hobart LXIC-6 Dishwasher

Kitchenaid Dish Drawer unit is canted forward; I need to get to the back legs to adjust them downward. How do I get to them?


Open the dishwasher door and undo the two screws that secure the face to the counter-top. Open the kickplate and slide the diswasher out of it's hole. You should be able to easily access the back legs now. It may be easier to disconnect the drain ... KitchenAid Dishwashers

Honda gas powered pressure washer--runs great and I get pressure throughout the system but nothing comes out of the wand itself. There seems to be no clog throughout the system . I have cleaned all parts. When the unit isn't started I can get flow throughout the system


... Pressure Washers

Have a GU1200XTL83 dishwasher. Getting power to the unit and to the computer board. No power @ the door latch. Any ideas on why not working??


... Dishwashers

Can't get unit to start.I have power to unit.


Some open the door in mid cycle ? Try shutting the breaker off and restart the unit. ... Maytag MDB8601AWB Built-in Dishwasher

I have a PLD3460RDC1 dishwasher.The power got shut off and it now displays an ER message with all the other lights blinking.I have shut off the power to the unit many times, first getting a PF error and then it goes to the ER with all lights blinking. How can I reset this?


HI, there has been a power surge/pulse, that has been absorbed by the electronic control board. There may be serious damaged here, in this case. You can try to reset the main logic chips by unplugging, or shutting power down for five minutes. If the ... Frigidaire Dishwashers

My Smeg Dishwasher (DIG12CA) is just 12 months old. It's as if there's no power getting to it. I have checked all external fuses and power is reaching the unit. Any ideas on what could be wrong? AG


... Smeg Dishwashers

Kitchenaid dishwasher # kudp01flss doesn't power on . Checked the unit is getting power from the outlet.


There is a thermal fuse located inside the control panel of the dishwasher. The part number for the thermal fuse replacement kit is 8193762.There were some noted problems with certain model dishwashers where the wire gauge on the thermal ... KitchenAid 34 in. KUDP01FLSS Stainless Steel Built-in Dishwasher

Our unit is not power on. It's plugged in and was previously working. The fuse is okay at the breaker. Any ideas? Is there a fuse within the unit that I can check? It looks like the screws to get into the lid are not standard. Thanks


... Bosch SRV53C03UC Built-in Dishwasher

I'm getting a PF power interupt code. When I press the "Start/Cancel" button the code goes away. Unfortunatly the unit will not power up. It appears to be completely dead. If I cycle the breaker the PF code comes back and we start the process again. What's wrong, help!! Bob


Hi,If pressing the cancel button doesn't get rid of the power failure error\015\012 "PF" then you have a bad control board. So you will need to replace \015\012the control board itself.You could try to disconnect the power su ... Electrolux Frigidaire Professional Series 24 in. Built-In Dishwasher Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1070 seconds