Having problems with your Maytag MDB9600A Jetclean II Built-in Dishwasher ?

Makes growling noise during the wash cycle. some vibration. unit is 6 or 7 years old. it is a maytag jet II EQ. cannot locate the model number as it is a built in unit. would appreciate any help. thank you


Answers :

Hi Spacepaint,\015\012No manufacturer hides the model/serial number behind the enclosure. Look closely on the side of the door panel edge and on the inside edge of the door jam. You will find the model number there.\015\012
\015\012Growling that happens on every cycle normaly indicates either debris in the sump area / filter or a failing pump motor. Remove screws and inspect the well area for debris.\015\012
\015\012Recommend a service call if problem is not resolved by the cleaning.
Repair Help & Product Troubleshooting for Maytag MDB9600A Jetclean II Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Makes growling noise during the wash cycle. some vibration. unit is 6 or 7 years old. it is a maytag jet II EQ. cannot locate the model number as it is a built in unit. would appreciate any help. thank you


Hi Spacepaint,\015\012No manufacturer hides the model/serial number behind the enclosure. Look closely on the side of the door panel edge and on the inside edge of the door jam. You will find the model number there.\015\012\015\012Growling that ... Maytag MDB9600A Jetclean II Built-in Dishwasher

We just hooked up our old built in GE dishwasher and the water is shooting out the left side of the unit where the black water hose enters the tub. Shouldn't the water be entering into the wash arm? The hose isn't clogged. It attaches to a white plastic piece that is part of the unit itself. The water is entering both the tub but also shooting out of 2 slits approx 1 1/2" each. located right below where u attach the hose.. Any help would be greatly appreciated!


... GE GSD5130 Dishwasher

Our church has a Vulcan Autosan built in Dishwasher, comercial style. The cable broke that raises and lifts the door. Here is the model numbers found on our dishwasher. R-16 BTF 81-07-1828-H If you have any idea where we could get this cable and how to put it on, we would appreciate it very much. My name is Donna Woods and I will put in my email address. Thank You, Donna


Hi Donna.Unfortunately the model number did not return anything after been entered in the online search box.The model name of this machine should be Vulcan R-16 ELT.Here the contact for Vulcan Hart parts distributors, call the ... Jenn-Air 24 in. JDB1100AWS Built-in Dishwasher

Hello, My Frigidaire dishwasher model number FDB1250REC2 is not starting the wash cycle, instead, the washing light starts blinking continuously when I press start. I turned off the breaker to the dishwasher and tried to start a load again, same problem! I would really appreciate any help that you can give. Thanks so much!


... Electrolux Frigidaire Professional Series 24 in. Built-In Dishwasher Dishwasher

I have a Maytag Quiet Series 300 Dishwasher (can't find any other model number etc). The normal and high temp wash lights are steady and the Start/Resume light is flashing. I've tried turning off the power and the high temp, heated dry, high temp, heated dry sequence but nothing works. Any help would be really appreciated! Thanks


... Maytag 24 in. MDB5651A Built-in Dishwasher

The lower spray arm came off during a dishwasher cycle and melted. The dishwasher is okay but I need a replacement spray arm for a Sears Galaxy dishwasher model number 587.15139400 I have searched google for replacement parts for this model and have not found a place where I can get a lower spray arm. Any help would be appreciated.


Sears parts dept ... Sears 24 in. 14181 Built-in Dishwasher

Hello, My Kitchenaid dishwasher has water coming out of the drain valve which is located on top of the sink. I figure that something might be clogged. Suggestions on how to approach this? Where would I find the model number? Thanks


Look around the edge of the tub opening where the racks pull in and out for the model # ... Dishwashers

We have a Kitchen Aid dishwasher model number KUDK03CTSS3. It's only about 3 years old, but the dishes on the top rack do not get clean. We thought maybe it was water not coming out the top, or food stuck somewhere, but do not know how to fix it. Any help would be greatly appreciated.


Had a simular problem, used product called dishwasher magic to clean it well and that took care of it. I got it @ walmart in the diswasher detergent area. Also be sure you are loading according to the manual. I now use lemi shine in every load fo ... Dishwashers

The salt light stays on and the machine will not come out of rinse cycle and begin washing. No manual, not sure where to put the salt.. Sorry no model number on machine. Inherited machine approx 10 years old. Any help would be greatly appreciated


... Bosch Dishwashers

We have an older Champios Model U-HB dishwasher and the heating element has gone bad. The picture in the manual I downloaded us J-shaped and the one in my unit is U shaped. Any info you can give me would be appreciated. Thank you in advance for your assistance.


... Dishwashers

I have whirlpool Dish washer model GU 120 ES (bought in 2001). When we start the dish washer cycle the unit starts for a minute, then the "start indicator" light flashes. As indicated in the instructions, we press the "start button" for five (5) seconds, at this time the washer clears the water out and stops. If you can assist this would be greatly appreciated. Thanks Jeff


I called the service tech.... ... Whirlpool Dishwashers

My lawn mower with a Briggs motor Wont start, has spark fuel is good , the unit is approx 5 years old, but seldom used, worked great last year, drained the fuel, and stored it for the winter.Refueled it and wont start. I can getting started if I pour a little gas down the carb, but naturally it wont run long. I'm thinking needle and seat, any help would be appreciated. Thanks


... Craftsman 2700 PSI Briggs Stratton Powered Pressure Washer

I have a Bosch built-in dishwasher model number SHU33A02UC/37 and it won't heat up hot enough anymore to sanitize and clean the dishes properly, it was sent with the repairman and brought back this way. Do you have any solutions? we were told it would cost 500 dollars to repair. Thanks


... Dishwashers

I have a Fisher Paykel dishwasher Model # DD603. It is about 5 years old. My problem is that the top drawer is difficult to open Pulling it open it becomes easier once I get beyond a certain point. The reverse is true when closing it. Any help would be appreciated. Thanks...Jared


Sounds like your lid actuators are not opening completely, they move the lid up and down. They are prone to failure, F/P has new actuators, German made, that can be installed and would probably solve the problem. ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Whirlpool DU1145XTPPB7 Whirlpool DU1145XTPB7 model. Normal cycle light started blinking sometime during end of wash cycle. It will not do anything. Things I have already tried and not worked: 1. Unpluged and pluged unit back in. 2. System reset w/ heat-dry button, etc. Any help would be greatly appreciated


These dishwashers normally have a "Control Lock" mode.  It's in the manual.  It is provided for child safety.  It's often controlled by holding the "No Heat Dry" button for 4 seconds or more -- same procedure turns it on or off. ... Whirlpool 24 in. DU1100XTP Built-in Dishwasher

Purchased ge dishwasher model ghda674n00bg and discovered after installation that I removed the rubber check valve from the discharge line in error. Is it mandatory that this check valve be installed? Naturally I would prefer not to remove and reinstall unit. Thanks for your help Regards, John


... GE Dishwashers

Parts needed I need an outlet pipe Part# V24A000Q8 and four brackets Part# V13A000A9 for a Equator model #SB-72/1 dishwasher. Any place where I can find them. Equator is out of stock and it could take 6 weeks to order. I would appreciate any help you can give me! Thanks, Pearl


If the manufacturer is out of stock...chances are you will not be able to find them anywhere else. Your best bet would be to go to a metal machinist shop and have some custom made. You can have this done for the pipe as well. ... Equator SB72 Built-in Dishwasher

I have a Frigidaire Professional series less than five years old. It won't run and flashes the wash, clean, and sanitize lights simultaniously. Any thoughts on what the problem is and whether it is worth fixing? This is the second Frigidaire I have had in ten years. The model number is PLD2851RDC3. Any help would be greatly appreciated before I go out and get my third dishwasher in ten years!


Hi.The two lights are not an error code, but they are telling that the machine is in failure mode.The error code is retrieved performing a water/service test.The water/service test is a special function initiated ... Haier HDP18PA Stainless Steel Free-Standing Dishwasher

I'm looking for the manual for our built-in Whirlpool dishwasher model DU1000CGT2 purchased in 2001. I am unable to locate the manual on your site and would like to have the manual on hand. Can you help with that?


Owners Manual - http://shared.whirlpoolcorp.com/assets/pdfs/literature/Use%20and%20Care%20Guide%20-%208051566.pdfInstallation Instructions - http://shared.whirlpoolcorp.com/assets/pdfs/literature/Installation%20Instructions%20-%208051229. ... Dishwashers

Is there a service manual for a GSD900D-03 GE dishwasher. My husband is an excellent diy handyman. We can't get water INTO the dishwasher. Would appreciate any help with location of water inlet valve. Thanks [email protected]


... Dishwashers

Ge dishwasher im having a problem with a dishwasher in a  home i just bought....it worked fine at first, now it has basically two cycles, off and wash....it will not try to fill, or pump out, it just washes.....the model number is gsd1100g02ww.  i took out the timer assembly and  found nothing  visibly wrong...but hey, i can fill it  up  myself with water and shop vac  it  out and it works"i tell my wife" i wont  tell u what she told me in return......any help i would appreciate.


Try taking the dishwasher out so u can see the bottom, or if u cant, pull the bottom front plate off, remove the plate, ull see a pump looking peice, small with main water line hooked to it, disconnect it and pull it off, u will need to take it ... GE 25 in. Nautilus GSC3400J Free-standing Dishwasher

I need to locate a circuit board part for a miele dishwasher G692 SCI PLUS. The part number is EPL 545-A. M.-NR. :05491860. iF YOU CAN HELP ME FIND WHERE I CAN BUY THIS PART IT WOULD BE MUCH APPRECIATED.


... Dishwashers

Leaking dishwasher My GE dishwasher leaks when running a load of dishes. The leak seems to be coming from about the middle of the tub about halfway back. I can't see exactly where it's coming from, but it appears to be dripping right behind the motor. Could it be a poor connection? I would appreciate any suggestions. Thanks, Bob Engle I do not seem to be able to find the model number


Probably a leak at the motor seal where it enters the tub. Best to remove the motor if you can and inspect the seal. ... Dishwashers

New apartment. The dishwasher won't work nothing moves inside when u turn it on. The dial in the front slowly turns and the base fills up with water and that is it. Encore model 363.16129100. Was hoping I was missing something simple. I do switch the lock closed before starting . Thank you any help would be appreciated


The movements are caused by the water pump inside sounds like the pump is jammed or bad.see if the propeller looking pieces turn free by hand if so the pump is not working. you could try and see if there something stopping the pump if you feel ... Dishwashers

I have an older bosche dishwasher and the I know the water is flowing into the unit and collecting at the bottom of the drain but it is not getting into the spray arms in the middle and top to work at all. Any help would be appreciated.. Thanks


There is a chacne that the main wash motor is not drawing enough water into the pump to spray through the arms.you can try and add some more water to the dishwasher and see if there is any change.\012if there is no change then you migh need to ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1188 seconds