Having problems with your Maytag MDB9600A Jetclean II Built-in Dishwasher ?

The glasses and cups have specks in them that don't rinse out. The soap dish doesn't clean out. I have take all the arms apart and cleaned them. There is no build up. We live on a lake and use filtered lake water. I have tried every kind of detergent. Washer has never performed well. It is about 4 years old but only used in the summer.


Answers :

Maybe try rinse aid like jet dry, some people forget to keep the rinse aid filled up or the rinse aid nozzle gets a encrustation build up from the rinse aid.
Also check your water for hardness, you may need to use a water softener to remove hardness, filter alone will not remove hard water.
One way to test for hard water is with a test tube or something like it and add 2 drops of washing up liquid, and shake the water and soap and see if you have a lot of bubbles or if the bubbles disappear quickly, if there is a lack of bubbles you probably have hard water and may need the mentioned water softener.
Repair Help & Product Troubleshooting for Maytag MDB9600A Jetclean II Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The glasses and cups have specks in them that don't rinse out. The soap dish doesn't clean out. I have take all the arms apart and cleaned them. There is no build up. We live on a lake and use filtered lake water. I have tried every kind of detergent. Washer has never performed well. It is about 4 years old but only used in the summer.


Maybe try rinse aid like jet dry, some people forget to keep the rinse aid filled up or the rinse aid nozzle gets a encrustation build up from the rinse aid.Also check your water for hardness, you may need to use a water softener to remove hard ... Maytag MDB9600A Jetclean II Built-in Dishwasher

Re: Creaftsman 2700 psi washer, model 580.752100 - I cannot use the detergent cleaning tank. The pump forces water into the tank, and it overflows onto the ground. If I try using the washer with the detergent shut-off value in the off position, the water pressue forces the valve completely out of the housing. Is there a simply fix for this or time for a $ervice call? sw


... Craftsman 2700 Max Psi Pressure Washer 23 Max Gpm

I have a Honda xr2600 power washer. When I tried using it, water was squirting from the top of the gun. I took it apart to find that there are o-rings on top of some kind of washer---looks like a lock washer but it's made of cardboard??? Two of these washers were broken. I can get the o-rings but I can't seem to find the washers. I tried getting the manual for this model on line with no luck. Any assistance will be greatly appreciated.


The washers that you describe are made of teflon and are split to facilitate installation and/or allow expansion as they wear. These washers are actually seals and at times are used together with orings to seal high pressure. You should ... Honda Pressure Washers

I have had my Bosch dishwasher for about 2 years. Over the last 8 months or so my dishes come out with a white film over them. I do have hard water, but have had it for over 20 years without a problem like this. The white film is all over dishes, silverware and the inside of the stainless steel washer. I use a rinse agent and have tried many detergents. I have used vinegar to clean the inside. What can this be?


... Bosch SHE45M06UC Built-in Dishwasher

A feew weeks ago Smeg STA6047 dishwasher stopped in the beginning of the programme after approx. ten minutes, and gave the error code E9. There had been clearly water in the machine, but maybe not enough and the detergent box was not open. However, when technician came by two weeks after, the dishwasher worked and he said it was in order. But only after being used only once, the same problem reappeared. First the washer gave the error code E8, on the second try E9. And now it does not start at a


As you know E9 is linked to the water inlet problem. \015\012\015\012There are two scenarios here - 1) Are you using the Aqua-Stop safety system? If this is trigerring then it can shut the inlet water. The reason it can trigger is if the ... Smeg Dishwashers

How do i turn on the water for my washer?I just moved in to my place, tried to start the washer but it started spinning before any water came in. I think the water must be switched off. There are two taps opening pipes going into the washer, a blue and a white one. Should I try opening one of these?


Yes open both of them they are the feed lines for the washer ... Dishwashers

I just had a Haus slimline dishwasher delivered and have tried to set it up. I have followed the instructions to the letter but the water inlet hose keeps leaking out water when you move the dishwasher into place after attaching the hoses. I have tried the manufacturer's hose they provided and two spare i have in my cupboard. I even went out and bought some 3/4" washers and added extra washers to the inlet hose, but it still leaks. What is wrong?


It is possible the dishwasher inlet is set for low water pressure.\015\012\015\012Check the water pressure setting matches your inlet water pressure.\015\012It might help if you provide the model number of the dishwasher. ... Dishwashers

It appears that the dishwasher is not getting enough water. I have made sure that there is nothing blocking the door area so that the soap can dispense and I have reduced the amount of detergent to maybe a 1/2 Tablespoon. Have tried both powder and liquid detergents. Ran a sani clean cycle with the Jet Dry product for dishwasher used in the rural. I also run the hot water in the sink prior to starting the dishwasher to ensure the water is hot when it comes into the dishwasher. The detergent


Hello,Welcome to FixYa.Based on your description you`re experiencing the ... KitchenAid 24 in. KUDP01IL - Multiple Color Built-In Dishwasher

Problem: dishwasher (moel MDB6601AWW) will not run. The front panel has a light, between the "Delay 1-9" and "heated dry" buttons, and adjacent to small printed icon (looks like a tombstone with the number 3 inside). Last weekedn I shut off all the water in order to change a faucet, including the hot water feed to the washer. Now the fed to the washer is somewhat frozen -- I can only open it 1/8 turn. So, I wonder if my wife tried to run the machin with no water flow, and it shut itself dow


... Maytag 24 in. MDBH955AW Built-in Dishwasher

GE TRITON dish washer. Utensils are stained after wash. I tried all that suggested solutions like cleaning with white vinegar, make sure hot water flows before it starts. I donot think we have hard water problem and also tried Jet dry rinsing. Nothing is working still i see utensils soap stains and not completely rinsed. I am desperately looking for an answer. I am thinking of is there a way i can test whether the middle tower is really opening up to spray water or not. It might be something els


Hi,The scum, film and white\012residue problems have started since the reduction of\012phosphates in dishwasher detergents.Here is a tip that\012will help you to solve the problem of films, residue, and scu ... Maytag Dishwasher

I have a fridigaire dishwasher PLD4555RFC0. The dishwasher now only cleans poorly if at all. The detergant used is powder and the detergant has been the same since purchasing the unit 3 years ago. The detergant does not completely dissolve on some dishes and is now staining/etching the dishes. I do not have a water softener, however, have tried the flushing with vinegar multiple times with no improvemnt. The water appears to be very hot as steam emerges when opening the door during the cycl


Sounds like your water is too hot(etching) and maybe not enough water should be about level with heater . ... Frigidaire PLD4555RFC Dishwasher

Im trying to turn on the washer ,but when press the normal cycle button and then start , the lite start to flush and the only thing the washer is doing is draining water, tried couple of times to let the draining finish and it is doing the same thing over and over again.?


... GE 24 in. GLD5500L Built-in Dishwasher

Briggs and Stratton pressure washer will not start. I have a 6.75 hp pressure washer that is only a year old. when I pull cord it turns over but does not start. I changed plug and checked it, I have spark when pulling. I have 40-50 psi of compression when pulling also. gas was drained and is brand new. it was working fine last time it was used. I have tried starting it without the water line or spray wand hooked up and no difference. After about 10 or 15 pulls, can smell gas when I am trying to


Hello dave, the problem is compression to low,you need 60 to 130 lbs to run engine,check for blown head gasket,or bad rings,or a stuck open valve,hope this helps,, ... Briggs & Stratton Pressure Washers

Water fills washer, program stops, inlet/drain flashes. checked all filters and pumps for blockages. none found. try again and washer empties water, then fills up again, program stops, inlet/drain flashes again. could it be a fuse???


Could it be.Try to open and look the fuse inside.Opps try to see the warranty of applian. ... Miele 24 in. G692SC Plus SS Free-standing Dishwasher

Maytag dishwasher- Model # WU 502 serial # 145 192 EP- 03 series Water builds up in the bottom of the dishwasher, does not overflow but will not go down. Nothing appears wrong in the drains. Dishwasher is connected to the kitchen sink drain. Tried a seperate rinse cycle but did nothing to eleviate the problem just made the water rise a bit but still did not overflow out of the washer. This washer is old and I cannot find the manual that came with it.


... Maytag 24 in. MDB6657 Built-in Dishwasher

I purchased a dishwasher in dec.07. I am not happy! My dishes are not clean! Silverware and glassware have a white coating on them. I've tried less detergent(cascade gel and powder)I tried more. Done the same with jet dry! I have added white vinegar this helps but still not satisfactory. We have also turned our water heater up so the water would be hotter.


Did you try to adjust the doseage regulator that is in the jet dry compartment fill hole, check your operators manual for info on this.\015\012 Good Luck ! ... Dishwashers

I have a ge dish washer model # gsd2000g00ww and it will continue to pump the water out when triing to fill for wash - i have checked for stuck float - seems to swith ok - i have tried to manually fill but still pumps water out and will not wash


Timer or control ... GE Profile PDW8060GSS Built-in Dishwasher

Hello, We have a Candy Diswater that is just arround 2 years old. When it starts it takes water and then you hear the washer going into loop. It tries to do something els but doesn't seem so. If you open the door you can see water inside but no progress or heating. If you also try to change the program it doesn't change as well. Before it got to this point sometimes we used to unplug the power and tunr it off and then ON and then it works. However, now this procedure is not working an


Quite possibly could be the timer and could also be the main control board as well. Sometimes unpluging it will help for short times but if a serious problem persists it will only be a temp fix... ... Dishwashers

I have a GE PDW8060GSS dishwaser. The washer does not turn on. The "anti bacterail" swith keeps blinking. There is some water standing inside the washer. Tried draining, but water keeps coming back. Not sure what is the issue. Can you help?


If after draining water comes back then you need to check the waste water system for any cloughs. Problem might even be at the dwelling drainage system as any blockages would prevent water from going out from washer. Check the waste hose, filter and ... GE Profile PDW8060GSS Built-in Dishwasher

My De Dietrich is not filling with water - pipe is on and water available. I've been away for a month - just got back and tried putting on the dish washer but it seems that the water isnt getting through to the machine even though the water pipe is on and waters available? any ideas - really grateful


Yes, lots of ideas. You need to disconnect the water line where it attaches to the dishwasher valve and see if water is flowing. If it flows, then you either have a clogged inlet valve (there is a screen inside the valve that catches debri from the w ... De Dietrich 18 in. VW7451 Built-in Dishwasher

I was replacing my sink faucet today and in the process turned the water off to the dishwasher. Subsequently my girlfriend ran the dishwasher without the water on! Now when I go to run the dishwasher no water comes out (meanwhile I've turned the water to the dishwasher back on). Is there some kind of reset? I accidently touched the coil in the bottom of the dishwasher just after trying to run it and it was hot. What do you recommend? Thanks. Mark


Hi,You need to investigate the following :-\015\012\015\012\015\012\015\012\015\012Drain line/air gap\015\012\015\012A\015\012clog in the drain line or air gap (if there is one) is the usual reason\015\012that a dishwas ... Kenmore Dishwashers

I have a ADG450 about 7 years old, the problem is there is dirty water left at the bottom of the dishwasher after finishing the cycle and the dishes look as if they have had the final rinse in the dirty water. also i have tried the rinse cycle with no dishes and all the rinse water had not drained away. I have cleaned the iside of the washer and where the water goes to the pump. Any ideas


Check the pipe leading from the dishwasher to the outlet, maybe under sink. this needs to be raise up as water will flow back into washer. Had this problem myself, felt foolish when the repair man just tied it up and left. ! ... Whirlpool ADG450 Slim-Line Built-in Dishwasher

Pump problems mine is the 14w. all that happens when i turn it on is the pump tries to drain the water, but there is no water to drain as the cycle has not started. all you can hear is the pump sucking water. no water comes into the washer either. somebody please save me.......


... Zanussi 18 in. DCS12W Free-standing Dishwasher

I have a Frigidaire Dishwasher, model #FDB635rfs It is not that old, but appears to have quit working. It sounds like it runs the water gets pushed in by the tube on the side but goes straight to the bottom of the washer. It looks like the spray arms are not spinning. Water is not circulating. Element still heats up. Detergent just runs down the inside of the door and doesn't dissolve since water is not circulating through arms. I have just replaced the water inlet valve and it did not hel


Don't know about yours but many of the rotating spray-heads are turned only by waterpressure, not a separate motor.\015\012The rotator is normally pretty loose and should turn willingly by hand; if it seems stiff and your water pressure is normally l ... LG LDF6810 Built-in Dishwasher

The water is not draining from machine, although the pump is obviously trying. It doesn't sound quite right. Kind of a growling noise. It can pump water into tubs when experimenting with ideas, but can't pump hard enough to pump the water into the sink. This is all done with the hose removed so we could check for debris in the line. I've checked the filters and they are clean and clear. This is a used machine a friend gave me, and it's been working beautifully until now.


Normal\012 0\012 \012 \012 \012 \012 \012 \012 MicrosoftInternetExplorer4\012 \012\012\012\012\012\012 /* Style Definitions */\012 table.MsoNormalTable\012\011{mso-style-name:"Table Normal";\012\011mso-tstyle-rowband-size:0;\012\011mso-ts ... Bosch 24 in. SMU40 Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1135 seconds