Having problems with your Maytag MDB9600A Jetclean II Built-in Dishwasher ?

Maytag dishwasher. The clean light stays on solid until I press any button then it blinks for several times then goes solid again. None of the other buttons light up when pressed. I unplugged it for over an hour to try to reset it but that did not help.


Answers :

Repair Help & Product Troubleshooting for Maytag MDB9600A Jetclean II Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Maytag dishwasher. The clean light stays on solid until I press any button then it blinks for several times then goes solid again. None of the other buttons light up when pressed. I unplugged it for over an hour to try to reset it but that did not help.


... Maytag MDB9600A Jetclean II Built-in Dishwasher

The washing, heated dry, and normal wash light just flash. I have unplugged and plugged it back in several time, i tried restting it by holding down the Rinse only button for 15 seconds. I pressed the high temp ater, heated dry, high temp water, heated dry buttons to try to reset. I also ran the hot water line that feeds the dishwasher until the water was hot. Nothing has helped. The machine is18 months old and therefor no longer under warranty.


Please provide the make and model number of the dishwasher.\015\012do you hear pumps running? what was the last cycle it was at when the flashing started. was there water left at the base of the dishwasher from the cycle that stopped? ... Dishwashers

I have a GE Profile dishwasher that stopped working after being unplugged for about 24 hours. Now only the timer lights up and no buttons work. Do I need to reset something after being unplugged so long?


... GE 24 in. Profile PDW9880JSS Built-in Dishwasher

Defy dishmaid dishwasher does not start wash cycle. Several attempts to reset dishwasher has been done. Machine has been unplugged for several days and switched on again and still does not work. The start/stop switch have been kept in for about 5 - 10 seconds to reset. When the machine is set to do washing, the water enters the machine and wash light shows green and machine remains like that with water inside the machine. The start/stop button is again pressed for 5 -10 seconds to drain the wate


... Dishwashers

I have a Whirlpool Gold Model GU2700XTSBO its only 4 years old. About two weeks ago i noticed that the green lights were flashing and it would not run, I unpluged it for an hour and pluged it back in and the lights went away and it worked ok for the last two weeks. Last night I went to use it and there is no power at all to the washer, I checked the power source to the outlet and there is power there, so I dont know if there is a reset button or some control panel problem?


... Whirlpool GU2700XTSB / GU2700XTSQ / GU2700XTST Built-in Dishwasher

I have a Whirlpool DU1048 that started out with a blinking clean light. I reset the dishwasher by pressing the heated dry and normal buttons twice. That worked the clean light stopped blinking. The problem now is the dishwasher seem to be stuck in the wash cycle. I finally have to turn it off after over an hour washing. Is this possibly a heating element problem? is that user replaceable?


... Dishwashers

I have a GE dishwasher model number GLD55OOLOOWW. It was starting a start cycle and i opened the door to put more dishes in and my finger must have hit a button on the door and now two lights flash off and on and it wont reset itself. It has been on for several hours and still blinking and beeping every so often and unplugging it does not help. Any suggestions how to solve this problem. Thank you.


Try pressing the cancel button ... Dishwashers

A few days ago the dish washer was running fine, maybe a single wash every day. Then, out of no were the logic seems to have left the machine. If you pressed the "normal cycle" button it would blink for about 30 to 45 seconds then the front panel would go blank. All LED lights would turn off, like it finished doing the diskes, never running a single cycle. I unplugged the machine to let all circuits reset, that worked for two days, two washes in that time. Today I'm back to a machine that will n


Your control panel is faulty and will have to be replaced. This is the main brain of the machine. Normally when a cycle doesn't start the timer is bad, but when your control panel doesn't do anything, then it is faulty. ... Dishwashers

I have a Kitchenaid Dishwasher Model KUDC25CHSS1. (Manual says KUDC25CH). The Delay Hours button is stuck on 2 hours. The manual says to cancel it, press it until no lights are on, but when we press it, the Child Lock light comes on. I tried pressing Energy Saver Dry to cancel the Child Lock, but that didn't cancel it. I tried turning off the circuit breaker for 5 minutes, but the same light(s) come back on when I re-set it.


... KitchenAid 24 in. KUDS01FLSS Built-In Dishwasher

My kenmore elite model # 253.4448370 keeps beeping and won't stop. We try to press reset button because high temp and power failure lights are flashing but when we press reset button it doesn't seem like the button works..it doesn't reset like it use to...does anyone know how to make this beeping stop? It appears that the temps are right for both frig and feezer but beeping won't stop...HELP!!


... Kenmore Dishwashers

Reset Button When I plug into outlet. I press the reset button the red indicator light will show but when I push the test button the red indicator light comes off. What does this mean I have a Karcher 1500 psi K2.25


Your testing the no fault short or motor overload feature. the red light indicates you have power. no light no power. ... Karcher 2500 PSI Pressure Washer

We have a new Whirlpool Dishwasher Model GU3200XTVY3, serial # F00404693 bought in April 2010. Yesterday,when we pressed the "normal" button, it started flashing then when we pressed the "cancel" button, it started flashing also. The dishwasher will not start when we pressed the "start" button. We tried to reset by turning off the power to the dishwasher and then turned it back on. All lights were off and then we pressed the "normal" button and it started flashing again. When we tried to pr


... Whirlpool 24 in. GU3200XTPS Stainless Steel Built-in Dishwasher

Dishwasher Kenmore Ultra Wash model #1777990 the 2 hour delay light is on and when I try to cancel the door lock button starts flashing I hit cancel and open the door and shut it and the 2 hour delaay button cmes on and will not go off. Is there a reset button anywhere.


... Dishwashers

GE GSD5320 seemed to finish all light wash cycles. Then it began to beep, with the NORMAL light blinking. I hit RESET, but none of the other buttons worked. I threw the circuit breaker for this appliance and waited an hour. I Turned the circuit breaker on but now I get the NORMAL light blinking, even when the door latch is not engaged. No buttons work.


... GE GSD5320DBB Dishwasher

Hotpoint BC145 Dishwasher not cleaning starts to kick in but then just sticks on the "R" light flashing and cannot reset even after turning off. Itbeeps when pressing the select button sound weaker and shorter than they used to and the light does not move from the "R". On a couple of times I have tried it has reset and then the dishwasher starts but after about 3 minutes there is a low beep(not the usual beep when a programme finishes) and the washer stops and the light is flashing on the "R" ag


... Hotpoint 18 in. BCI45 Slim-Line Built-in Dishwasher

For my Kudi01dl model dishwasher, the rinse light is on, but the unit will not respond to any buttons being pressed and won't turn on. When I press any buttons, two horizontal lines show in the front, but go off as soon as I let go of the button. Is there a ways to reset the unit? Everything was functioning fine the last time I used it. I use it about once a day. The problem started when I heard sounds coming from the unit, very loud motor sounds. The door was closed but I had not turned


... KitchenAid 24 in. KUDI01DL - Multiple Color Built-in Dishwasher

I have a GE Profile Eterna series triton dishwasher. When it gets t rinse cycle, lights go out and it keeps rinsing. Buttons stop working and it won't stop or reset. If I unlatch door and wait for hours lights may come back and allow a reset. Run through 3 rinses only -fine. wash cycle does it again.


... GE Dishwashers

I have a KitchenAid KUD1021RWHO dishwasher that will not turn on when I hit the start button. The LED lights work when I press cycle selection ie. "normal" but when I press the start button nothing happens. I have waited for a couple of hours and then it will start. However during the last week it has happened more frequently and now it has not worked for the last (2) days. Any ideas as to what the problem may be? Thank you for your help!!!


Hello,\015\012\015\012This is a very common issue on these units. The touch pad has failed. You can try to flip the breaker off for several minutes and see if that clears the code. More than likely the touch pad will need to be replaced.\015\01 ... KitchenAid 24 in. KUDI02IR Built-in Dishwasher

I press the test button and red light goes out. I then press reset and the light comes on and washer won't run.


... Campbell Hausfeld PW1750 Electric Pressure Washer

I have a GE Quiet Power 3 that has completly died. I cannot get a light to come on or anything to beep when pressing buttons. I checked the circuit breaker and outlet and they are both working fine. I tried pressing and holding the reset button on the front control panel and nothing. It seems to have just died at 2 years old. Anyone have a solution? GE wants $80 just to look at it.


A dead set simply means a cut off of power supply. Open the back cover of your dishwasher . Locate the area where the AC cord is located and look for the plastic fuse holder which is usually installed in one of the AC cord line open it and replace t ... Dishwashers

I have a kitchenaid dishwasher, SS, model # KUDIO1ILBL6. When you press the ''normal'' button to run it, nothing happens. Tried other cycles and same thing, the green light goes on above the cycle but its just not starting. I tried resetting by opening, pressing high temp scrub then energy saver dry, high temp scrub, energy save dry, then close and hit cancel. Is there any other combo to reset it? or does it sound like something else is wrong? thanks!


... KitchenAid Dishwashers

I have a Maytag MDBH945AWB and it stopped working. When you press Start, the lights are very dim and does not start the cycle. If you select the 2/4/6 hour delay, this light is bright but when you press Start, the cycle does not work. Is the control board bad or the buttons


... Maytag MDBH945AWW / MDBH945AWQ / MDBH945AWB Built-in Dishwasher

My dishwasher will not start. If you unplug it and plug it back in it says 1H, no matter what button you press it then says 2H and if you press another button it will say 3H until it runs through to 9H then will display --. It will continue to do this until you leave it alone and walk away. Then after a few moments it will clear itself out and the 'Normal' light under cycles will continue to blink. The dishwasher is 3 maybe 4 years old. Please help, I have a 3 year old and an 18 month o


Hi,There could be Few Possibilities.Let's try to Reset. 1h, 2H -----9H usually shows delay X hours Display where X would be 1,2...9.Turn the Power OFF for few minutes, say 5 Minutes and then Turn it ON. ... Dishwashers

I have a Kenmore 665 ultra wash quiet guard 3. The red light at the start/resume button flahes continuosly. I have unplugged it and tried the four button reset. Neither works. The red light still flashes. Any ideas?


The /RESUME light flashing constantly means that there is either have a bad door switch or a touchpad failure.In some case the problem is a faulty control board.The control board cannot be returned.I suggest replacing control pad fi ... Kenmore 24 in. 15689 Built-in Dishwasher

We have a Beko DWD5410W dishwasher that has worked fine...until today - the 'wash' light is on but it is not wasing. I have pressed in the 'start' button and held for 5 seconds to reset and it then springs to life draining out or whatever that noise is, and then if I turn the dial to a setting (even the cold prewash) and press 'start' again it starts whirring away, then after about 10 seconds just stops, with the 'wash' light staying on. Not blocked, I have checked - this likely to be a frozen p


... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0881 seconds