Having problems with your Maytag MDB9600A Jetclean II Built-in Dishwasher ?

After a cycle the washer does not drain water used. it just sits at the bottom of washer


Answers :

Power from the house
Is there power getting to the dishwasher? This\015\012can be difficult to test, because dishwashers are usually wired\015\012directly to an electrical circuit, rather than plugged into the wall.\015\012But at least check for a blown fuse or a tripped circuit breaker.

Door switch
The\015\012door switch is important because, if it's defective, the dishwasher\015\012won't work at all. To reach it, you need to remove the control panel\015\012cover, or sometimes the interior liner of the door. If it's defective,\015\012you need to completely replace it.

Wiring
Often the main\015\012wiring connection from the house, at the dishwasher, burns and breaks\015\012the connection. If that's the problem, the wires must be\015\012repaired/replaced as necessary. If that's not the problem, check the\015\012wiring to the door switch, the wiring between the door and the lower\015\012part of the dishwasher, and the wiring to the timer. Repair any broken,\015\012burned, brittle, or defective wiring, using the proper appliance-grade\015\012wire and connectors.

Timer or selector switch
Although it's\015\012uncommon, the timer or the selector switch may be defective. If so, you\015\012need to replace the defective part, because neither of these can be\015\012repaired.
Repair Help & Product Troubleshooting for Maytag MDB9600A Jetclean II Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

After a cycle the washer does not drain water used. it just sits at the bottom of washer


Power from the houseIs there power getting to the dishwasher? This\015\012can be difficult to test, because dishwashers are usually wired\015\012directly to an electrical circuit, rather than plugged into the wall.\015\012But at least check for ... Maytag MDB9600A Jetclean II Built-in Dishwasher

Kenmore Ultra Wash Quiet Guard - will not drain at end of cycle. After cycle is complete, water (not clean) sits at the bottom of the washer but I still unload the dishes and then turn the cycle dial around again - going past all the water heating and filling and washing - and land on the drain cycle, it will drain. Any ideas why it will not drain when I let a cycle run, but will drain once I cycle it through to the drain option?


... Frigidaire 24 in. PLD2850 Built-in Dishwasher

My bosch dishwasher runs fine, cleans fine, drains fine....but after it has been just sitting for a while, the bottom very slowly fills up with water. Each time we run the machine the water level drains back to the normal amount in the bottom of the washer after the cycle is complete. The problem is if we are away for a few days, the bottom fills up and overflows onto the floor.


Water inlet valve isn't closing all the way closed. Need a new one ... Bosch 24 in. SHU53 Built-in Dishwasher

Hello, I have a Kitchen Aid (model # KUDMO1T JWHO) dishwasher that runs the motor in all cycles, with water fill & drain working fine, but the pump is not pumping water during any cycle, as the spinners and the inside of the washer are dry when I open the door, except for the water sitting in the bottom. Also, no normal swishing sound of water when the motor runs in any cycle. Looks to me like a mechanical break in the pump drive. How do I check the pump drive on this model? Do you have any


... KitchenAid Dishwashers

I have a kenmore 665.13719k601, i used the delay switch and now i found water in the bottom of the machine. the cycle most have stopped while i was away. when i returned there was water sitting in the bottom of the machine. The water is clean... I can not drain due to no access to power on the machine. I checked the breaker but it was on, so i reset it anyway... nothing.. any idea's


... Kenmore 13719 / 13712 Built-in Dishwasher

GE GHDA485N 10CS Dishwasher that has standing water in the bottom after the cycle completes. I pulled it out and reconnected power and ran a rinse cycle. I could see that water was pumping out the clear drain pipe but there was still about an inch of standing water in the bottom. Any thoughts as to what part has failed. Does the system use a water level switch or a timed drain cycle to determine when the water has pumped out. If it is a timed cycle could a slow drain cause the problem. Thank you


... GE Dishwashers

AEG OKO_FAVORIT 6281i dishwasher - error code 20 (Siphon blocked). Out of the blue after 6 years of reliable once-a-day family use, my AEG OKO_FAVORIT 6281i dishwasher started OK but about 3 minutes into the cycle began flashing error code 20. At which point there was a litre or two of cloudy water sitting at the bottom of the machine. Since then I've tried redirecting the drain hose into a bucket, after disconnecting it from the kitchen drain. Same symptom, and no outflow except what was al


... AEG 23 in. Favorit 50750Vi Built-in Dishwasher

Dishlex Global 310 model. My dishwasher has water sitting on the bottom of it and it wont drain. I noticed it after I did a cycle of dirty dishes and the 'fast' light was flashing when I went to open it. Which shouldnt have been because it was on a normal wash. The water has been sitting at the bottom for 2 days now and still wont drain! I've taken out all the parts on the bottom which come out and cleaned them. Still no change however.


Just ran another cycle and it was fine ... Dishwashers

Dish washer does not drain after the cycle is complete. The last few months when the dishwasher is done their would be a small amount of water left in the bottom. It didnt create any problems but would smell after a few days. So we would just run the drain cycle and it would empty. Well i got home to and the wife said the it was really full. The water was dirty and when you run the drain cycle it didnt drain. She said the dishes were clean. So i cleaned the vent, and filled the sink with


Check drain hose and drain pump.End of drain hose must be in same level with machine.Try it. ... KitchenAid KUDR01TJ Dishwasher

I have a Bosch SHU53513UC/U12 dishwasher. My initial problem is that the washer smells bad after a cycle and I've noticed some water sitting in the bottom of the unit. After running a diagnostic test, it results in a "2" heating fault. I followed your advice and used a current coil to and attached it to the GYBK-a1-3 hot wire on the control board. After running the test again, it only gets as high as 1.15A and manual says it should reach 11A. What should I do next?


Hello,Welcome to FixYa. ... Dishwashers

The disk washer doesn't drain at the end of the rinse cycle. There is a humming sound but no water is forced through the hose to the sink/garbabe disposal. At the end of the wash, there is a large amount of dirty water in the bottom of the washer. I removed the spray arms, the spray arm holder and the screen and then removed the water, and found a couple of pieces of plastic. But I don't see how I can remove additional parts from the washer bottom. What could the problem be? Is there a fi


Is the dishwasher drain hooked to the garbage disposer? If so is it new? If so did you knockout the plug in the disposer? If so then you either have something clogging the drain or pump. Or the pump motor is bad. ... Dishwashers

Kitchen Aid dishwasher Model# KUDP01FLSS. 2 problems #1 Won't run unless you press in on the door and hold it for a few minutes then it runs through cycle normally. Problem #2 It won't drain water out at the end of the cycle when I open the door there is water laying in the bottom of the tub. I have checked the drain hose for clogging and it appears normal. I am able to remove the hose from the disposal and suck the water out of the tub using a shop vac this indicates to me that the drain is ope


... Dishwashers

Hi I have a problem with my Bosch SHU43CO6UC/22 dishwasher. using "power scrub plus" and "regular" cycles it will continue to fill and overflow the door, after the cycle has run even when the power button is off. I am using the quick wash cycle at the moment .After the cycle has run i open and check if the water has drained or not,If it has it does not continue to fill and flood.If there is water in the bottom after the cycle has finished it will keep rising untill I push the rinse hold button


The bosch dishwashers use a fill valve that is attatched to the inlet hose. yours is stuck in the open position. this usually happens when you have hard water, as the minerals build up on the sealing surface of the water valve. there is no easy ... Dishwashers

We just purchased a used Fisher and Paykel DS 603-i. After installing and running the normal cycle there was a lot of water left on the bottom of each drawer. We ran the bottom drawer (water stil siiting on the bottom of the top drawer) and part way through the main wash cycle we got what I think was a F1 error code (we do not have the LCD version but the Rinse light was activated). I took out the bottom drawer, dried out the basin and then took out the washer and reattached the drainage pipes t


Hi\015\012\015\012\015\012Thanks for using FixYa. F1\015\012error means that the flood switch has been activated. You’ll need to reset it by poweri ... Fisher and Paykel 24 in. DS-603 Built-in Dishwasher

My trusty Bosch s510 Dishwasher which has been going strong for about 17 years (at least) has just decided not to empty itself. I noticed the bottom was full of water after a wash. I emptied all the water out by hand and presuming there is a blockage in the drain tried using a plunger to unblock it. I have since put it through another cycle and half way through water started leaking out of the front. At the end of the cycle the bottom of the dishwasher was again full of hot 'soapy' water. If th


Same problem, so went out and bought a new bosch. Problem with the S510 was cured by lubricating the pump out motor bearings with a squirt of WD 40. If you don't know which pump, follow outlet hose to pump outlet.Les ... Bosch Dishwashers

I have a Kitchen Aid KUDS03CTSS3 dishwasher. Dirty water is staying at the bottom and nothing comes out the drain hose during the entire cycle. The drain hose is looped above the kitchen P-trap, although for a time it wasn't. I use a wet vac to get the water out but there is still water below the fine filter. I thought if I could get the fine filter off, I could clean out the bottom as I think that it's full of crud down there that may be blocking things. I can't figure out how to get the l


Hi,Thanks for the follow up. I am glad it worked out for you. If I can Help in the future let me know. http://www.fixya.com/support/c64627-kitchen_aid ... KitchenAid 24 in. KUDP02FR Built-in Dishwasher

The bottom drawer is filling with excess water after the top drawer cycles. It doesn't hamper the use of the bottom drawer as the excess water drains during the cycle, but I am concerned about rust, etc. from the excess water standing in the drawer. Please advise. Denise Arnold


Hi\015\012 \015\012This means that you have an overflow leak problem. You need to shut off circuit breaker or pull fuse. Next let it dry out for up to 4 days ,peak under dryer and feel metal drip pan and ... Fisher and Paykel Dishwashers

It appears to finish it's cycle, as far as the dishes are clean - however there is clean water that has pooled on the bottom. you can hear the water fresh coming in - the pump comes on for a few minutes, drains some of the water and shuts off - the pump comes on again - drains some of the water and turns off. I turned the water going into the dishwater off - the pump ran for a few minutes - drained some of the water and then just sits there with the red power light on - there is still the same


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. Dishwasher not draining properly or not draining at all issues\015\012can arise due to different reasons ... Bosch 23 in. SHU3302UC Built-in Dishwasher

When washing dishes, the washer drains okay at the end of the cycle. However, ir seems that for some reason in the mornings we are finding water in the bottom of the dishwasher--sometimes so much that some has leaked out to the floor. When the drain cycle is turned on, the water goes out okay? Any advice?


Sounds like a bad fill valve. ... Kenmore Dishwashers

I have a kenmore Ultra Wash Dishwasher, Model 15825691. We were recently hit by lighting. Once hit, the dishwasher started up. Since then, all cycles work, however, at the end of any cycle, the dishwasher continues to run and fill the bottom of the washer up to about two inches and then cuts off, so when we open the washer, there is approx 2 inches of water inside no matter what. I have pressed the "Cancel/Drain" button, in which drains the water after two minutes, but when that is finished, the


There must be a problem wit the fill valve. Check which valve the water enters. Check first the wiring to the valve of the water inlet or where the water comes out to fill the washer. Check for physical evidence of damage on the solenoid (or contr ... Kenmore 24 in. 16539 Built-in Dishwasher

Bosch Integra SHU 9955US/12 - when we start wash cycle, the detergent dispenses and the tub fills with water, but the wash cycle never starts (never spins spray bars). Seems like timer is counting down, though, but doesn't start "washing". After waiting awhile, we are able to use the "Cancel/Drain" mode to drain the water. The drain filter in the bottom of the tub is clean.


Sounds like your motor is burned out. The drain motor and wash motor are seperate on your machine. You can check for power going to the motor, but to do this you might have to pull the dishwasher out. While the cycle is running check for 120 VAC g ... Bosch SHU9955UC Built-in Dishwasher

I have a GE Potscrubber 720 and there is water in the bottom of the dishwasher and I tried to clear it by starting a cycle and it still keeps water in the bottom of the washer. When I run a cycle there is caked on soap on the inside door and dishes and the dishes are filthy. I found a long thin piece of metal by the drain it is long and straight and a break on one end and an "L" shaped bend on the other.. Any ideas where to start looking for problems? As I have no experience in repairing dishwas


... GE 24 in. GSD2600GBB Built-in Dishwasher

Maytag dishwasher- Model # WU 502 serial # 145 192 EP- 03 series Water builds up in the bottom of the dishwasher, does not overflow but will not go down. Nothing appears wrong in the drains. Dishwasher is connected to the kitchen sink drain. Tried a seperate rinse cycle but did nothing to eleviate the problem just made the water rise a bit but still did not overflow out of the washer. This washer is old and I cannot find the manual that came with it.


... Maytag 24 in. MDB6657 Built-in Dishwasher

My bottom dish washer was draining the water on the top dishwasher and there is always water left over on the top.I remove the pipes and put CLR to clean up drain.Start both dishwasher on rinse cycle ( 12 min cycle) then at 10 min.they start blinking with a No tap (may be water ) sign on it. I run the cycle again now a F1 sign coming with a tool sign.And both dishwasher going crazy ,it turn on by itself even I powered them off.


Hi\015\012\015\012\015\012Thanks for using FixYa. F1\015\012error means that the flood switch has been activated. You'll need to reset it by poweri ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

My built in Whirlpool adg 9340 washer won't start a cycle at all. It seems to start a cycle and after 1 minute it stops and it starts beeping. Also water remains on the bottom. As soon as the cycle starts it drains that water and brings new water in which stays there. It won't work for more than 1 minute....


... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2049 seconds