Having problems with your Maytag MDB9600A Jetclean II Built-in Dishwasher ?

I have a MDB9600AWW dishwasher and the led/control panel seems to have died. I get the odd noise when I hit the cancel button but I cannot set any of the functions anymore.


Answers :

When you cannot program the panel it has failed . but before replacing i would remove the panel and unplug the ribbon and reinstall it making sure the ribbon contacts are in and tight . there is a lot of mostiure in the panel and can cause poor contacts . if this does not correct problem then you need to replace panel . very costley $172.00 .. hope this helps mm feed back pls and thanks for ysing fix ya ..
Repair Help & Product Troubleshooting for Maytag MDB9600A Jetclean II Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a MDB9600AWW dishwasher and the led/control panel seems to have died. I get the odd noise when I hit the cancel button but I cannot set any of the functions anymore.


When you cannot program the panel it has failed . but before replacing i would remove the panel and unplug the ribbon and reinstall it making sure the ribbon contacts are in and tight . there is a lot of mostiure in t ... Maytag MDB9600A Jetclean II Built-in Dishwasher

Our Ikea Nutid Whirlpool dishwasher locked up recently. It started when someone was wiping off the top of the door where the control buttons are located. The dishwasher was locked on the china setting. Holding the cancel button, shutting off the breaker did not seem to clear it. Is there a way to reset the dishwasher? There was flashing on buttons but I cannot remember how many flashes or what one was flashing.


... Whirlpool GU2400XTP Built-in Dishwasher

My kitchenaid dishwasher was set on 4 hour delay button accidentally. It has been days and the light will not turn off, even after hitting cancel


... KitchenAid 24 in. KUDS01FLBL Built-in Dishwasher

My frigidaire dishwahser was set to run a normal wash cycle and heat dry. It never ran, the soap is still in the holder and the lock beneath the heat dry option is lit. I'm unable to cancel or select any other options. I cannot get the dishwasher to run. Do you have a solution? I have tried holding down a number of the buttons in different combonations but still can't get the light to go out or start a wash cycle.


Looks like a number of things are happening.\015\012\015\012It would be easier if you can provide the model no. of your frigidaire dishwasher.\015\012\015\012I am assuming you have turned the mains power off and on. ... Frigidaire Dishwashers

The Fisher Peykel dual drawer dishwasher : the top unit LED is off and the setting for length of wash is not lit up and is not functioning. There is power to unit because when I hit the lock button it beeps. Also the red light for the glass cleaning liquid compartment is lit. What seems to be the solution? I am an ME and hands on type, please advise.


Can you see a small lock inside the display panel??? the control may be locked. another issue might be a broken heater plate, not a very home owner freindly part to change( heater plate has a fuse inline that would kill power to function ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

I have the Quiet Partner II, DU1100XTPB7, and have already replaced the electrical ciruit board but having the same problem. When I hit any wash cycle button, the soak/scour & heated dry buttons light up, but will not "start." The "rinse only" button does nothing, but if I hit the "delay" button, then the soak/scour, cancel, and also the status buttons, washing & drying, all night up at once. The only button that seems to be working is the "cancel/drain." Although there's no water in the mac


... Whirlpool 24 in. DU1100XTP Built-in Dishwasher

I have a KitchenAid Model KUDP01FLBT5. After I push one of the clean buttons, and the start button and close it, nothing happens. The indicator lights for the buttons come on as you push them. When this first started, you would ahve to open and close the door and re-set the buttons (not sure if that button re-setting had anything to do with it) up to 20 or 30 times, and it would eventually come on. Now it won't anymore. Help!


Hi\015\012\015\012Thanks for using FixYa. To\015\012resolve this you will have to reset the console. Do this by closing the door\015\012and press these buttons in sequence...\015\012\015\012 ... KitchenAid 24 in. KUDP01FL Built-in Dishwasher

Our Whirlpool ADP 6515 has a delay button. When the button is pressed and activated for a 3 hour, 6 hour or 9 hour delay, if we change our minds and want to wash immediately, we cannot disable the button!! How can we deactivate the delay setting to wash immediately? We have pushed the delay button over and over to turn it off but it will remain on the 9 hour delay setting. We are very frustrated. Please help.


Try switching the power off at the wall switch for a minute, then switch back on, to clear the memory. ... Whirlpool Dishwashers

Dishwasher Kenmore Ultra Wash model #1777990 the 2 hour delay light is on and when I try to cancel the door lock button starts flashing I hit cancel and open the door and shut it and the 2 hour delaay button cmes on and will not go off. Is there a reset button anywhere.


... Dishwashers

Whirlpool GU940SCGQ2 the 2 hr delay was blinking, I hit cancel. Now nothing works but Cancel button. If I hit Air Dry it starts Cancel cycle again.


... Maytag Dishwashers

I have a Whirlpool gold quiet partner III The type # is 575-0 The model number is GU1200XTL03 The cancel button and the pots and pans button are blinking continuously together. I cannot get it to cancel so I can run the dishwasher. What do I need to do?


Hi.You need to click a button sequence in rapid succession. First perform the steps below:Try first holding down the cancel button. If that does not work, try tripping the circuit breaker for one minute. ... Dishwashers

Good morning. I have a KitchenAid KUDM01TJ with a constantly flashing "Rinse" light. when I hit the "Cancel" button, it too flashes in the same time with the Rinse light. I left the machine alone, came back a few days later and saw that the issue had resolved itself - but I didn't use the machine. A few days later, the "Rinse" light was flashing again and naturally, I hit "Cancel" to see if the same thing happened and it did. This time the lamps are still flashing. I read through the other repo


No its not the problem of button secquence.its the problem of keypad circuit this is creating this problem.as the circuit is getting overheated and it stops working.the key pad sometimes functions and sometiomes doesnot.in this case the key pad circ ... Dishwashers

I have a Whrilpool Dishwasher Model GU2500XTP. The rinse aid light is flickering rapidly. We have refilled the rinse aid dispenser. Hit cancel button and nothing happens. Hit the Start button nothing happens...Any solutions??


... Dishwashers

Dishwasher fills with hot water. Float OK - water feed stops when full. Motor humms but no water spray (in all opperating modes). Cancel selection (with cancel button) and close the door. The water drains then the unit shuts off. Water feed OK. Drain Cycle OK. Looks like spray pump hung but do not know. Cannot find a reset button (as with disposal) or way to free hung pump motor. I did see glass pieces in the drain. Possibly a small piece hanging the motor.


If you found broken glass inside the machine some has likely migrated to the pump. about the only way to fix that issue is to remove the pump and either replace it or disassemble it and clean it out. ... KitchenAid 24 in. KUDP01FL Built-in Dishwasher

Kenmore Ultra Wash Dishwasher Model 665.15779 LOCK ON light blinking on control panel, unable to use washer. If buttons were locked, LOCK ON light should be lit continually not flashing. If you press and hold NO HEAT DRY button to disengage lock, nothing happens. If you press the CANCEL button it begins to blink in unison with the LOCK ON light. How can I stop the light from blinking to allow button function again?


... Kenmore Dishwashers

I have a Kitchenaid Dishwasher Model KUDC25CHSS1. (Manual says KUDC25CH). The Delay Hours button is stuck on 2 hours. The manual says to cancel it, press it until no lights are on, but when we press it, the Child Lock light comes on. I tried pressing Energy Saver Dry to cancel the Child Lock, but that didn't cancel it. I tried turning off the circuit breaker for 5 minutes, but the same light(s) come back on when I re-set it.


... KitchenAid 24 in. KUDS01FLSS Built-In Dishwasher

Kenmore Dishwasher model # 665.16602300 Control panel push buttons do not function except cancel and delay buttons. No other buttons work at all. Thanks for help in advance Rich Bussmann


... Kenmore 16602 / 16604 / 16609 Built-in Dishwasher

I accidently hit the start button twice and, I guess, set the machine for a delayed start. How do I reset it so that I can start it now? And it's (just now) set to the pots and pans (which is fine) and hot dry (which I don't like) and won't let me change the settings


\001 To cancel the delay and start the cycle, press START/RESUME. ... Whirlpool 24 in. GU2500XTPS Stainless Steel Built-in Dishwasher

The "Rinse Only Button" will not function even after going through the "Cancel" cycle.


Br, sounds like you have a stuck keypad. This would be the only reason it is switching to a different cycle. Catriver..post back. ... KitchenAid 24 in. KUDS25 Built-in Dishwasher

Kenmore elite model 665.1669 or the 1769 model. All lights are working except for the start button light. When i hit the start button nothing happens. No blinking light, it's like it is dead. Cannot start the washer.


It appears your timer/main controller/CCU has failed in this instance.For replacement parts - head on over to PartSelect.com or RepairClinic.com and enter in your full model number for a full parts listing.I recommend both sites bec ... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

I have a KDW 243 A dishwsher. It was opened before the end of the cycle, and I cannot re-set it. Befor ethis, it was working fine. Whatever I do, the drain pump runs as soon as the power button is pressed, and the programme button does not operate.


Hi\015\012\015\012\015\012\015\012\015\012\015\012Thanks for using FixYa. This\015\012issue can be either due to a faulty door latch or door lock switch which is not\015\012engaging itself. And, if the door latch will not engage the ... Dishwashers

I have a whirlpool quiet partner i dishwasher (model DU1055XTSQ2) that has suddenly stopped working. Control panel has partial functionality. All of the buttons on the control panel have a green LED feedback light when depressed. None of them provide LED feedback anymore except the Hi-Temp Wash, Sani-Rinse, and Heated Dry buttons. So there is power to the dishwasher. Any ideas? Please help Scott


The control board has failed.CLICK HERE to see the parts breakdown. ... Whirlpool DU1055XTSQ Built-in Dishwasher

KUDS02SRSRSS1 dishwasher.......remodeling kitchen, disconnected dishwasher.....reconnected and have power (lights are working), however when hit start or cancel button on front door, nothing happens. Is there a "reset sequence" of buttons that I need to press?


I am assuming you have tried to turn the power off and on again after a delay.\015\012\015\012Most likely the door switch is not engaging. Have you tried to push the door a bit hard. Sometimes the dishwasher is not aligned correctly with ... KitchenAid 24 in. KUDS02SRSS Stainless Steel Built-in Dishwasher

I have a Maytag quiet series 200, it been working fine since I purchased it last year, as of today I pressed start and it won't start and yet when I press the delay buttons of 2, 4, 6 it lights up and so do the other functions but to change my settings that doesn't work neither as well as my start button. Whats wrong with it? Any ideas? My model # is NY2222514


... Maytag 24 in. MDBH940AWS Built-in Dishwasher

I have the kitchenaid dishwasher model #kudv03ctss0.the clean light stay blinking and when i hit the start it just blinks and then stops but the clean light stay blinking constantly.if i hit the cancel button i hear a um noise as if it going to turn on but nothing happens and the light stays blinking. what do you think might be the issue .


Dear friend,\015\012ngfam at you service! happy to assist!\015\012It's an electronic problem!The lights are called codes and need to be diagnoed by a factory service person!!We sell appliances for 65 years an ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0956 seconds