Having problems with your Maytag MDBH955AWS Stainless Steel 24 in. Built-in Dishwasher ?

Dishwasher does not drain...stops in cycle...no matter what cycle

\015 For example: \302\240I pressed the light wash cycle, which should take around 80 minutes...dishwasher stops after about 8 minutes, and doesn't drain...has happened a couple of times, have had to drain by hand.\015\012\015\012Also, the regular dishwashing cyle washes for a couple of hours, and stops...then starts again even when not pressed.\015\012\015\012\015

Answers :

HI, this is a control fault. the logic chips are malfunctioning. these chips are responsible for initiating the proper washing cycle sequences. you will need to replace this damaged control board asap.

Click here to order your new control board online.
Repair Help & Product Troubleshooting for Maytag MDBH955AWS Stainless Steel 24 in. Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My Bosch dishwasher has several problems: 1) Water doesn't completely drain out and dishwasher kind-of smells when I open it -- I do keep the filter very clean. 2) The dishwasher takes HOURS to go through one load, no matter what the time says on the display and no matter what type of cycle you choose -- quick, delicate or regular. 3) The red display often displays something that looks like "2h" at the beginning of the cycle. 4) The place where you put the detergent doesn't shut.


Hi Kathryn .I think you have a defective pressure switch. The pressure switch is located near to the drain pump, and the device is used to determine when water had been drained completely.Also check the floater switch located ... Dishwashers

I have a kenmore Ultra Wash Dishwasher, Model 15825691. We were recently hit by lighting. Once hit, the dishwasher started up. Since then, all cycles work, however, at the end of any cycle, the dishwasher continues to run and fill the bottom of the washer up to about two inches and then cuts off, so when we open the washer, there is approx 2 inches of water inside no matter what. I have pressed the "Cancel/Drain" button, in which drains the water after two minutes, but when that is finished, the


There must be a problem wit the fill valve. Check which valve the water enters. Check first the wiring to the valve of the water inlet or where the water comes out to fill the washer. Check for physical evidence of damage on the solenoid (or contr ... Kenmore 24 in. 16539 Built-in Dishwasher

No matter which cycle selection in pushed, the dishwasher only starts up in the "normal" 93 min cycle. If I try other cycle options, and persist, I get an ER message and the cycle stops prior to the soap powder door opening and never completes the cycle. Only with turning off power for several minutes and receiving the PF message, and resetting ONE TIME that message can I then select any cycle, at which time the machine "defaults" to the "normal" full cycle. If I do not disturb that cycle, it wi


Looks like you are having a good deal of problems with the dishwasher.\015\012\015\012It will be helpful if you provide the make and model no. of the dishwasher.\015\012\015\012At this stage I can speculate the controller (ass ... Dishwashers

My Frigidaire dishwasher stops in mid-cycle and the "Hi Temp" &" Air Dry" lights blink on and off together. This happens no matter what cycle i begin with. I cut the power to the dishwasher for ten minutes and rebooted, but still received the same result.


... Frigidaire 24 in. PLD2850 Built-in Dishwasher

Our dishwasher model is a Nautilus FP920WW. The unit switches on OK and displays the normal wash cycle settings but when we try to start or change a cycle (or press any button for that matter) all we get is a quick, intermittent beeping and nothing happens/changes. Switching the dishwasher off and on again at the wall does nothing to solve this problem. What's going on???


... Fisher and Paykel Dishwashers

Dishwasher is making a loud grinding noise when it's started. Doesn't matter the cycle choice; the cycle starts as normal then once started up starts making a sort of grinding noise as the water is pulsing, like something is stuck or blocking the "push" of water. I couldn't see anything stuck in the bottom - any thoughts before I call a repair person? I've never owned a dishwasher before - maybe there's a basic drain/blockage thing I should check out first? And, any recommendations for repair


... Maytag 24 in. MDBH970AW Built-in Dishwasher

Westinghouse Virtuoso 922 dishwasher. Wash cycle completes, but water does not drain out. If I let the cycle continue, after a delay the rinse cycle starts, but of course no clean water is pumped in so the dishes are "rinsed" in the dirty wash water. The wash cycle itself is successful with water pumping all around the washer if I open the door mid-cycle. I have removed and cleaned all filters which were correctly fitted so I am confident there is no foreign matter inside pump. When the water sh


... Dishwashers

Dishwasher does not drain...stops in cycle...no matter what cycle


HI, this is a control fault. the logic chips are malfunctioning. these chips are responsible for initiating the proper washing cycle sequences. you will need to replace this damaged control board asap. ... Maytag MDBH955AWS Stainless Steel 24 in. Built-in Dishwasher

I have a kitchenaid dishwasher model kuds24se with a problem. I MUST hit cancel before I hit start. Note that it doesn't matter how long it's been since the last cycle. It could be a few minutes or a day or more. I have to hit start to get a complete wash cycle. If I don't hit cancel, the washer goes through some sort of cycle and stops. It seems like a normal cycle but of course it is not because I don't hear any water and, upon completion, when I open the door there is heat but the soap dispen


... KitchenAid KUDS24SE Built-in Dishwasher

I have a Beko DE2431FW Dishwasher which has stopped working. I select a cycle and then press start, the green light starts to flash and the cycle begins to start but after about 30 seconds it stops and the red 'end' light comes on. this happens no matter what cycle I chose. Can anybody help me with this please?


... Dishwashers

My dishwasher starts no matter what cycle on a 2 hr hold, it doesn't hold it goes ahead with the wash cycle. And it won't shut off when the cycle is finished. Sometimes it starts like it's supposed to but most of the time it just has a mind of it's own.


... Bosch SHU5307UC Built-in Dishwasher

My Kenmore Elite dishwasher model number 665.16463300 will not start on washing cycle but on sensing cycle. And it does not matter which wash cycle I choose. How can this be fixed?


... Kenmore Elite Stainless Steel 24" BuiltIn Dishwasher with TurboZone Rotating Spray Jets 13103

We have a Frigidaire Gallery Series dishwasher we just purchased in August. Model #GLD2445RFB2. We are experiencing a problem with it. We noticed it started running louder then normal and now it will not finish a wash cycle. It gets half way through and PF lights up on the display and the cycle never finishes. It doesn't matter which cycle we choose it has done it on all of them.


... Frigidaire Dishwashers

Dishwasher stuck on china cycle model number GLD6210L15ww no matter what button pushed to put on any other cycle as soon as we hit start it goes to China Cycle *very frusterating*


... GE 24 in. GLD6200L Built-in Dishwasher

My Dacor dishwasher will only do the 10 minute rinse cycle. No matter which button I push, it only does the 10 minutes rinse cycle. We have tried clearing it, we have unplugged it, we have tried every single button, but it continues to only do the 10 minute rinse cycle. What do we do?


... Dacor Epicure ED30 30 in Builtin Dishwasher

My Brada dishwasher very seldom finishes a cycle but stops and beeps Er. It doesn't matter what cycle it is on either. Also two times when the door is closed and is off it will beep and the china


... Dishwashers

Brand new Indesit IDS 105 Dishwasher will only run pre wash cycle, no matter what its set on - factory reset info required


Purchased a second hand Indesit slimline IDS105, to find it would only complete the first wash cycle, at the end of this cycle the LED Would just flash, with the waste pump coming on every 2 mins to empty it. Even after 4 hours it still didn't comple ... Dishwashers

My smeg dishwasher is stuck on soak doesn't matter what cycle I try it goes back to soak there is no water in the dishwasher tho


... Dishwashers

Dishwasher overheating I have a beko dishwasher AAA and it does not matter what program you use the water water heats up and boils. When the cycle is finished and the end light is on, the machine is still heating. All my glasses are cracking :(


... Beko Dishwashers

My dishwasher will not start. If you unplug it and plug it back in it says 1H, no matter what button you press it then says 2H and if you press another button it will say 3H until it runs through to 9H then will display --. It will continue to do this until you leave it alone and walk away. Then after a few moments it will clear itself out and the 'Normal' light under cycles will continue to blink. The dishwasher is 3 maybe 4 years old. Please help, I have a 3 year old and an 18 month o


Hi,There could be Few Possibilities.Let's try to Reset. 1h, 2H -----9H usually shows delay X hours Display where X would be 1,2...9.Turn the Power OFF for few minutes, say 5 Minutes and then Turn it ON. ... Dishwashers

Whirlpool GU1500XTLQ (2004). Having a major problem with soap suds. No matter how little soap we add, the suds remain at the end of the cycle and will somewhat still remain after running another rinse only cycle. We have verified that the water is flowing to the dishwasher and the top and bottom arms are rotating.


... Whirlpool Dishwashers

The dishwasher isn't cleaning well and doesn't use much rinse agent. I have tried and tried to figure out why the dishwasher isn't washing dishes well and I can't figure it out. I haven't called the manufacturer yet and maybe I should. I've changed the cycles and that doesn't matter. First thing is that it doesn't really use very much rinse agent, so my glasses look yucky. Second thing is that I can tell it hasn't cleaned the dishes well because the inside of the door isn't clean. With a s


Hi, \012I have an older dishwasher also and recently mywife also complained about it not cleaning right... so me being the man I amtried in vain to clean the things... Bought new spray arms online and installedthem in minutes...now the thing works li ... Jenn-Air 24 in. JDB1100AWS Built-in Dishwasher

I have a hotpoint HDA3400 dishwasher and it will not fill with any water. It goes through the cycles but will not fill with any water no matter what cycle I start it on


Hi\015\012\015\012\015\012This is happening due a a faulty fill valve or due to blockage in fill hose. Please check the water inlet hose, try removing it and check for any blockages. If the inlet water hose is fine then you'll need ... Hotpoint 24 in. HDA3400G Built-in Dishwasher

I have a GU1500XTLB1, type-575-0 Whirlpool Gold dishwasher. For the last couple of weeks I've been getting the control lock on. I got the manual out, I hold the air dry button and it clears. My problem is now when I turn the machine on dosen't matter which cycle I hit (pots and pans, normal, or quick wash) it runs for about 5 minutes and it goes into a mode with the timer having lines going horizontal with the air dry button lit up and rinse button lit up. It sounds like it starts the cycle


Hi,There are Few Tricks to Reset this. Follow the below Tricks :-1. Try holding down heated dry key for 5 secs. I believe that is the control lock/unlock button on your model. IF not, look for the lock symbol and follow same i ... Whirlpool Dishwashers

My Mezzo MDW012 dishwasher stops when going to the 2nd phase of a cycle...It doesnt matter which cycle it does this on all of them


I have the same problem.. Have run several cycles in all configurations and stops during the wash cycle with the first 3 lights remaining on after beeping stops.. did you manage to solve? ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2369 seconds