Having problems with your Maytag MDC4650AW Built-in Dishwasher ?

Float does not shut off the water when dishwasher is being filled. IWater keeps running, fills up and runs out of the front of the dishwasher. Also it will not pump the water out at end of cycle.


Answers :

Check the float to make sure it moves freely up and down, and it should click when it moves. Remove float and clean around the float tube-you may need to do this from below, through the access panel. Use white vinegar to scrub the float and shaft assembly. Turn on the dishwasher to see if this fixed the problem.
\012

If not, it may be the float switch. If you are handy with electrical repairs, turn off the power to the dishwasher, pull the dishwasher from the wall and remove the back. Remove the wires from the terminals on the float switch-use masking tape to identify to identify terminals,noteing which belongs where.Remove old switch and replace with the new float switch. You will need the serial number, model number and make of your dishwasher to order the new float.

Repair Help & Product Troubleshooting for Maytag MDC4650AW Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Float does not shut off the water when dishwasher is being filled. IWater keeps running, fills up and runs out of the front of the dishwasher. Also it will not pump the water out at end of cycle.


Check the float to make sure it moves freely up and down, and it should click when it moves. Remove float and clean around the float tube-you may need to do this from below, through the access panel. Use white vinegar to scrub the float and ... Maytag MDC4650AW Built-in Dishwasher

Kenmore dishwasher. The upper rack is not getting clean. Even very light residue remains. And, detergent is left in door at end of cycle. The bottom is filling up, so I don't think it's the intake valve. Also, all the blade openings appear clear. I am noticing that hot water is not filling the dishwasher when I first run the cycle. Even if I have hot water running in the sink, the dishwasher fills with cold or warm water. So, I think this is the problem. What should I do? Thank you in advance!


I find it odd that the dishwasher is filling with cold water if the water is hot at the sink. It sounds like the dishwasher is connected to the cold water line rather than the hot. Check under your sink; if you've got standard plumbing, the dishwas ... Dishwashers

I have a De Dietrich DV640JE1 built in 45cm Dishwasher, working fine for over 3 years. After replacing the connection under the sink to fix a leak it has stopped working. But I dont think this is related. I run a cycle and it fills water in the bottom of the machine, it drains it out in the end but the 2 arms are not rotating and no water comes out. I checked the arms and they are not blocked. A faint clunking sound can be heard at some part of the cycle. I did also run a cycle with the dr


Hello Benny,\015\012\015\012It's highly unlikely that replacing the connection under the sink is related to this problem.\015\012\015\012From the symptoms you describe, it's almost certain that the circulation pump motor has f ... Dishwashers

My whirlpool dishwasher is ocasionally filling back up with water, whether the door is open or closed, and regardless of of control panel being lit. It happens, then leaks out the front. If i run the cancel drain, it will pump out the water just fine. All the other cycles are working just fine, and it leaves no water at the end of of the cleaning cycle. I have found no common occurance for this


Greetings,\012\012 in most instances the water inlet valve is leaking..this is the water valve that brings water into the dishwasher...its possible, the drain water is running back into the d/w from the drain hose not installed prope ... Dishwashers

Hello, I have a Neff Dishwasher S5453X1GB/74 and it's not draining the water out at the end of the cycle. I have unscrewed the filter and released the impeller. I have also cleared the waste pipe that runs to the sink waste and put loads of cleaner in the dishwasher. The pipes seem to be clear as water goes somewhere during the cycle but backs up at the end. A few times when I started a cycle the water did not spray out but I could here the drainer or motor? running. I jetted water through th


... Neff 24 in. S5453X1 Built-in Dishwasher

Hello, I have a Kitchen Aid (model # KUDMO1T JWHO) dishwasher that runs the motor in all cycles, with water fill & drain working fine, but the pump is not pumping water during any cycle, as the spinners and the inside of the washer are dry when I open the door, except for the water sitting in the bottom. Also, no normal swishing sound of water when the motor runs in any cycle. Looks to me like a mechanical break in the pump drive. How do I check the pump drive on this model? Do you have any


... KitchenAid Dishwashers

I have a Bosch SGS43A22 Dishwasher approx 8 years old. When I start a cycle it fills, runs for about 15 minutes, then drops out about a litre of water from the bottom of the door, then completes the cycle without any more leaking. I have run the machine with the front panel off and can see that water bypasses the top of the seal and fills the well of the seal then pours out. It only happens the once. The seal is fitted correctly. Any solutions?


After 8 years service the seal may have perished, so you should feel for a crack by stretching the rubber where you noticed the leak. ... Bosch 24 in. SGS43C12 Classixx Free-Standing Dishwasher

My dishwasher has stopped cleaning plates properly. It makes everything wet but at the end of the cycle the detergent block is half dissolved at the bottom. I have just run a cycle and opened the door during this. The bottom is full of soap suds and water and the top spray bar is dripping water after I open the door but when I close and then reopen a few secs later the top spray bar has definetly not rotated. The water is also not hot, this dishwasher is a cold fed only machine so I guess the el


Hi, \012 \012I have an older dishwasher also and recently my wife also complained about it not cleaning right... so me being the man I am tried in vain to clean the things... Bought new spray arms onli ... Zanussi 18 in. ZSF4123 Slim-Line Free-standing Dishwasher

I have a kenmore Ultra Wash Dishwasher, Model 15825691. We were recently hit by lighting. Once hit, the dishwasher started up. Since then, all cycles work, however, at the end of any cycle, the dishwasher continues to run and fill the bottom of the washer up to about two inches and then cuts off, so when we open the washer, there is approx 2 inches of water inside no matter what. I have pressed the "Cancel/Drain" button, in which drains the water after two minutes, but when that is finished, the


There must be a problem wit the fill valve. Check which valve the water enters. Check first the wiring to the valve of the water inlet or where the water comes out to fill the washer. Check for physical evidence of damage on the solenoid (or contr ... Kenmore 24 in. 16539 Built-in Dishwasher

I have an Ariston LS245 dishwasher, have just had the pump replaced, as it had shorted out, due to water in the bottom tray where the water detection float is, also a new drain hose fitted. Have just run a wash and after running a while, presumably to the end of the rinse, wash and dry cycle, then one of the cycle phase lights, the one for 'soak' blinks constantly. I switched the machine off and had a look to see if a wash had been done, the dishes look clean. In the book it says that if one


... Ariston Technologies Dishwashers

My Bosch SHY56A02 dishwasher won't fill....When cycle is started, it seems to pump water out but none in. Water feed is good....Added water manually and it pumps out immediately. Also, unit continues to run with door open...door switch is not jumpered. Could it be the fill valve? More likely the control module? Thanks for your help!


Hi,\015\012\015\012As water is filling in your dishwasher a float rises along with it. When the float reaches a predetermined level it shuts off the flow of water by activating a switch thereby preventing a leak. Sometimes the float can g ... Bosch Dishwashers

Hi. I have a Siemens SE65E331GB Built in Dishwasher with an aquastop system. The problem is that it seems to be stuck at the end of a cycle. The pump is constantly running when stitched on. I won't top after a reset and it continues to run even if you open the door. The water supply light also comes on indicating that there is no water getting to the machine. I have tried resetting the aquastop as per the advice in other threads. This has helped in that the water supply light now stays


... Siemens Dishwashers

Got a lound buzz type noise that I thought was a bad solenoid on the water valve. Tub also filled up & overflowed1 Replaced water valve ($30), but now dishwasher wont run thru cycles or fill with water to wash--seems to be stuck on drain even though digital counter counts down. What should I check next?


You may have dislocated the connection that controls the AquaStop circuit.\015\012\015\012This is linked to the inlet hose. Either the connector linking the inlet tap to the inlet valve is loose or the float switch has triggered.\01 ... Bosch 24 in. SHU53 Built-in Dishwasher

Won't Fill My Zanusi studio compact dishwasher won't run. All the usual lights come on and I can hear the "ticking" but it doesn't fill with water so at the end of a cycle nothing has happened. The water supply is good. I've had this happen before and when I disconnect the supply hose and reconnect it, everything is ok again!


Hello Ben - I understand your dishwasher has power but will\012not fill with water. Here are a few simple\012troubleshooting tips that may help you resolve this issue:\012\342\200\242 Make\012sure water supply is turned on. (First check for shut ... Frigidaire 24 in. PLD2850 Built-in Dishwasher

Dishwasher starts and runs to 2nd rinse cycle, when pump starts to pump water out, all lights on front display flash along with key pab lights blinking. you can turn off and restart, but is does the same. Diswasher will also try to start when in off mode. Replaced circuit board and it does to same. Did I get a bad circuit board or is there another problem. Also when I try water service test, I get a Rinse aid fault.


U REPLACED THE CIRCUIT BOARD IN THE DOOR, THE ONE BEHIND THE CONTROL BUTTONS? THAT IS THE TIMER, IT IS KNOWN AS THE CCU OR CENTRAL CONTROL UNIT, THAT IS WHAT CONTROLS ALL TIMED FUNCTIONS, SO THAT REALLY IS THE ONLY PART THAT CAN CAUSE THIS PROBLEM ... Frigidaire 24 in. FDB1050REC Stainless Steel Built-in Dishwasher

Fisher paykel Hi I have a fisher paykel dd603 dishwasher. when I run the bottom drawer on its own ,,it also fill the top drawer with water ! so after the dishwashing cycle , im left with water in the top drawer. im guessing that a valve should close on the top drawer to stop this happening? is there a part I could order and replace myself? thanks [email protected]


Check your email ... Fisher and Paykel 23 in. DD603H SS Free-standing Dishwasher

I have an Asko DW1875 dishwasher (10yrs old) which has just recently started having problems. The initial symptom was that during a washing cycle, unit showed '1' and inside became very hot (melting some plastic cups/plates in unit). On further investigation (with diagnostic mode), the dishwasher is filling and draining with no problem. When circulation pump runs there is barely any water pressure in blades (just dribbles out) and water leaks into undertray via a plastic white tab near front (v


... Asko D1876 Dishwasher

My frigidaire dishwasher FDB1502RGC4 will not run a cycle. it will fill and drain the water but will not run a wash cycle. all the lights on the control panel lightup when they should. so i dont think it is a fuse. and there is not much i can see after i opened the front door, the control module and the console assembly. could it be one of these.


Having the same problem with mine, just replaced the discharge pump last week because it went out, worked a couple days now this. still have not figured out the problem ... Frigidaire FDB1502RGC Built-in Dishwasher

The dishwasher does not appear to be draining properly any more. There is soap residue on the door after it runs. Also ther s a small pool of water by the food drain after the cycle ends. The glasses all have a residue on them after the washing cycle ends


Hi,The scum, film and white\012residue problems have started since the reduction of\012phosphates in dishwasher detergents.Here is a tip that\012will help you to solve the problem of films, residue, and scu ... Asko 24 in. D3121XL Free-standing Dishwasher

I received a second-hand as-is Akso D3530 (model #107353001) dishwasher. It washes perfectly fine, but at the end of the cycle, it keeps running. It does not seem to be the drain that is running, but rather the circulating pump. I have fully emptied the pan of water (there was only a little in it (you couldn't see it until you removed the sieve) using a turkey baster and it keeps running. I also checked the float sensor in the bottom. The float sensor is not tripped, and when I manually trip it,


Hi.The float switch is not a water level switch, but an overfill switch. The control board uses the input from the pressure sensor to decide when to stop the pump.When you open the float switch circuit the machine 'thinks' that ther ... Asko 24 in. D3530FI Built-in Dishwasher

Frigidaire dishwasher won't end cycle - will run on and on for hours. Sometimes it cycles through, usually it just endlessly washes and rinses. I have to CANCEL the cycle, which causes the dishwasher to empty and run a few RINSE ONLY cycles (which are consistent, cycle time wise) to rinse the soap off of the dishes. Also, the door for the soap seems to stick - how long into the cycle before the soap door should open? Also, does opening the washer during it's cycle (to add more dishes) change or


I would say the resettable thermostat has failed. There is a thermostat which senses the water temperature, and when it fails, it causes the dishwasher to run constant. Replace the thermostat underneath the dishwasher and that should cure problem. P ... Frigidaire 24 in. FDBB540 Built-in Dishwasher

The dishwasher top drawer is leaking all over the floor during the cycle. When the top drawer is running, It fills up the the bottom of bottom drawer with water also and then neither drawer drains completely. The water is a light brown color after a wash and often half the soap is left in the dispenser.


Fisher and Paykel design a air gap kit to prevent the water back flowing to the other while one is running. it really works and worth of your money.\015\012You need to change the lid seal and a pair of actuators from the top drawer. Because of the ... Fisher and Paykel DD605SS Stainless Steel Dishwasher

My dishwasher is not cleaning dishes... The cycles work but the dishes do not get clean an sometimes are more dirty if that is possible. I have tried adding jet dry and extra cleaning liquid but get no results. also there are times that the bottom of the washer fills with water unexpectedly and will even leak on to the floor. It doesn't leak when the dishwasher is running... I just don't know what to do other than clean out the spray arms. Please help.


Hi,Check your heating element.. Dishwasher ... Kenmore 15899 Built-in Dishwasher

Bosch SGS5312GB/12 Dishwasher I had a control board. Worked fine except didn't heat the water. Got it repaired (new PCB). Now the only thing it does is drain. Clicks every 20 secs and carries on draining. Got a new board. Does everything (including heat the water) except it does not drain before, between, or at the end of cycles. It does drain when while filling, and if the flood detection rod is raised manually (also drains if the inlet pipe beyond the pressure sensor is blocked - found


... Bosch Dishwashers

The fuse in the plug keeps blowing. Initially it would run for a while - sometimes 3 or 4 cycles - before blowing. It now blows the fuse the second that I plug in to the socket, even with the on/off button on the front of the dishwasher set to off.I'm keen to take it apart, but it's full of water as it blew mid-cycle. Is there a clever way to empty the machine without the power being on, or do I need bits of hose and sponges?A schematic blow up would also be extremely helpful.


Lower the outlet hose into a washing up bowl, it should then Drain. Check the heater to see if it is earthing you get to it by removing the right hand side panel. ... Hotpoint 24 in. FDW60 Free-standing Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2682 seconds