Having problems with your McCulloch Pressure Washers ?

My McCulloch power washer FHH20A motor froze what do I do

Answers :

Remove spark plug and spray penetrating oil down hole let sit for a day, take small hand held propane torch and heat up outside cylinder wall not to hot. take small punch and insert thru spark plug hole gently tap with hammer while trying to start , this should free piston. do compression test right away to make sure no holes in piston. mine did this after a couple of years sitting.
Repair Help & Product Troubleshooting for McCulloch Pressure Washers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My McCulloch power washer FHH20A motor froze what do I do

Remove spark plug and spray penetrating oil down hole let sit for a day, take small hand held propane torch and heat up outside cylinder wall not to hot. take small punch and insert thru spark plug hole gently tap with hammer while trying to start , ... McCulloch Pressure Washers

I have a McCulloch H.P. power jet cleaner 1300 and when i switch the device on the motor starts running but the pressure is not building up so no water is coming out of the pressure washer gun. We bought the device in 1999. Or alternatively is there anywhere in the UK to get the repairs carried out? Many thanks Michele.

... McCulloch Pressure Washers

Power washer I have a karcher power washer and it haves a 7.0 robin motor on it... When i start it up the motor just goes in to high speed... I looked to see if all the springs are on the arm and they are ....All i can think of that the governer on the motor is not kicking it back... If you could help that will be great....Thanks Jerry

... Karcher 2500 PSI Pressure Washer

I have an electric power washer model PW181000AV with about 25 hours on it. Got home from my winter retreat and used the power washer about 1/2 hour on the driveway. Everything worked fine. Went to complete the job the next day, and the motor would not power on. No sounds at all, like it wasn't getting electricity. Did the standard trouble shooting with ground fault and on my own electrical system. Been using the same outlet for all the time I have owned the power washer, so distance is no

... Campbell Hausfeld Pressure Washers

I have a Craftsman power washer model 580 752020. When I start it up, turn on the switch the electric motor runs fine until I either close the trigger to the spray nozzle or press the trigger for power spray. The electric motor just shuts down, if I take my finger off the pressure and let the water run with no presssure the motor runs fine. My question is this. Is the capasitator on the electric motor the probable cause and is there a way to check out the capasitator to see if it is malfuncti

I doubt that it has anything to do with the capacitor on the motor. i think you are having a problem with the actual Motor Drive circuitry. What is happening is when you close the switch, this tells the Motor to "Ramp Up" to pump the water out, what ... Craftsman Pressure Washers

I have a Honda ,gas powered power washer and when I squeeze the handle the water pump kills the motor. I've let the engine run until warm and it still can't take the water pump engaging. It's a three year old washer.

... Pressure Washers

I have a McCulloch FH160B power washer and it no longer builds up pressure. I haven't used this very much at all. I tore it apart and cleaned everything I could find. When i pull the trigger for the spray nozzle, I get line water pressure. When I release the trigger, the power washer sounds like it starts to build up pressure. When this was working correctly, the pump would shut off when the trigger was released. Any suggestions?

... McCulloch Pressure Washers

Brand new Stanley 1800 power washer - just bought it yesterday. Powered it on - realized I hadn't turned the water on - so turned it off - turned the water on and turned the Stanley back on - it ran for a second and powered off. Now it won't turn on again. Did I burn out the motor?

... Stanley Pressure Washers

I have a McCulloch FFF16H power washer intake leaks

... McCulloch FHH18A Electric Pressure Washer

My PW8TSS JCB power washer motor does not work

... Pressure Washers

The washer keep kick out the overload? - McCulloch Electric Pressure Washer 1800psi 145 GPM Induction Motor Cart

... McCulloch Electric Pressure Washer 1800psi 145 GPM Induction Motor Cart

I have a go kart with a honda power washer motor that I just purchased.It lacks power at start and stalls alot.Put new pull in,sprayed carb cleaner,adjusted carb,new air filter,need to know if it need a fuel pump and were to get one

Hondas are gravity feed no pump needed .You might need to clean the card though. ... Karcher 2500 PSI Pressure Washer

Fisher paykel dishwasher dd601I runs complete normal cycle and finishes normally. 2-3 sec. after completion the washer motor srarts to run and the f1 fault (flood sw. activated) is dislayed. When the power button is pushed the fault spontaneously disappears and the motor stops. no moisture is in thre bottom under the tub and the normal cycle can be ru again with the same results.

Hi\015\012\015\012F1 code indicates an overfill condition which may cause when dishwasher can’t pump out dirty water due to a plugged drain hose.\015\012open dishwasher fully ,dry up as much water as possible the ... Dishwashers

I have a McCulloch FHH18A power washer. When plug it in without the water turned on, the pump will start. As soon as I turn the water on to the unit, the GFCI power cord trips. Water does flow through the unit as I have water at the wand nozzle when not plugged in. Any suggestions?

I would guess there is a leak somewhere inside the unit that is spraying water on some electrical component and causing a ground fault. ... McCulloch FHH18A Electric Pressure Washer

I have a Karcher 330 electric power washer. When connected and set to highest pressure (on variable wand) I get no motor action unless I reduce wand setting, then I get a little boost but not much. If I use high pressure conical wand I get high pressure sometimes, other times motor does not go and no pressure is delivered. I have replaced the high pressure hose.

Just wondering. have you tried it without an attachment to see what kind of pressure you get ... Karcher K2.26 Electric Power Washer

How do i hook up a hose to the power washer - McCulloch FHH18A Electric Pressure Washer

Have you tried looking on the back of the machine? ... McCulloch FHH18A Electric Pressure Washer

The dish washer ran its full cycle but won't shut off. the little pump motor in the very bottom keeps cycling water in the bottom. it won't shut off when you open the door, it won't shut off when you push the power button and the front switches won't respond. the little light on the front of the dish washer is blinking and it has never done that befor normally the lites are always on solid.....

The drain stuck cycle ( I presume you mean drain pump running constantly ) are directly related with overfill scenarios for Asko dishwashers of this ... Asko D3122XL 24 in Builtin Dishwasher

I started working with the Karcher KB4040 pressure washer and all was well for 1-2mins, then it sputered a bit and all power died. All hoses were still attached properly, it hadn't blown a fuse in my house and the fuse in the plug of the washer is working fine.When I switch it on I get nothing. Do you think the motor has packed in? I borrowed the machine from my neighbour who's away on holiday, so don't know much about age of the machine. Any advice much appreciated.

If the water is in anyway impeded, like kink in hose the unit turns off and goes into protection mode. That it it shuts down for a pewriod of time depending on how hot it may have got.\015\012When its rested try it again ensuring you definitely ... Karcher 1750 psi Electric Pressure Washer

I was using my Karcher 350M pressure washer working fine but it just stopped having tripped the power boards circuit breaker. The breaker now trips each time I switch on the washer. There is no smell of burnt motor and the electric did not get wet when last in use. Appreciate any suggestions or tests that can be made. I have a decent multimeter. Thanks.

... Karcher 1750 Psi Elec Pressure Washer

Draper power washer keeps cutting out. Power ok, water running through ok but motor stops

... Pressure Washers

I have a pw1380 model power washer that the motor will not resume running when you sqeeze the trigger on the handle. This occurs when you have been running the washer and stop. Can the ISS be jamming and if so, how do I get the housing off to check it.

... Pressure Washers

Husky 1650 PSI power washer motor runs continuously but does not have any pressure

... Pressure Washers

K3.8 power washer motor runs when trigger released & water is leaking from the bottom of the unit.

... Pressure Washers

Pro user petrol power washer motor cuts out

... Pressure Washers

Karcher 4.99 power washer motor will not switch on

... Pressure Washers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1111 seconds