Having problems with your Mi T M 2 Hp, 110V, Twin Stack, Compressor, 4.1 CFM 100 Psi ?

Compressor stopped compressing during floor installation. Was at 100 psi and now has dropped down to80 psi. The unit will not start. Outlet is fine, checked with other applicances. Compressor had been working for 5 hours previously.


Answers :

Check if there is a overload/temp reset button the end of the electric motor?
Repair Help & Product Troubleshooting for Mi T M 2 Hp, 110V, Twin Stack, Compressor, 4.1 CFM 100 Psi

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Compressor stopped compressing during floor installation. Was at 100 psi and now has dropped down to80 psi. The unit will not start. Outlet is fine, checked with other applicances. Compressor had been working for 5 hours previously.


Check if there is a overload/temp reset button the end of the electric motor? ... Mi T M 2 Hp, 110V, Twin Stack, Compressor, 4.1 CFM 100 Psi

Wont start I've had the washer for many years with minimal problem. Yesterday when I closed the door no light went on and the washer would not start.  After 20 minutes or so it suddenly went on and worked fine.  I thought that it might have not completed its last cycle. Today, however, I had the same problem and it's been over an hour and still hasn't started. (I checked the circuit breaker and it's fine)


Give it a firm push over the door latch once you've closed the door..it might be the door switch not activating. oops.... first and formost isolate from power for 5-10mins and try ... Bosch 24 in. SHU43 Built-in Dishwasher

My 3-yr old GE Profile dishwasher lost power soon after initiating wash cycle. Checked braker switch...fine. Checked outlet power...fine. Dishwasher power mysteriously came back on approximately 12 hours later. Initiated another wash cycle and lost power again after a few minutes. Water remains in bottom of tub. What's wrong????


First thing i would check is the actual wiring behind the toes kick\015\012you will seea wire box, shut the breaker off, open up the box and double check all your connections there,\015\012 the next step would be to check the voltage ac ... GE 24 in. Profile PDW8280JSS Built-in Dishwasher

My pressure washer runs 4 about 20-25 min then it starts knocking and pinging then shutsdown it has plenty of oil i checked it and replaced it with 5-20 oil it starts hard always has if you let it sit for about an hour it will start back up sound fine and work good untill it happens again any thoughts to what might be happening to it?


Sounds like the engine is overheating either due to restricted air flow over the cylinder and head assembly, or the engine is running very lean due to a plugged fuel filter, dirty carburetor, or plugged muffler. Hope this helps! ... McCulloch FHH25A Gas Pressure Washer

Hi, I have a Dewalt pressure washer 3100 psi. I want to know why the pressure washer works okay for 1 hour then it stop working completely. the oil is fine, the spark plugs are okay, and when I tried to start it again it does not work. Can you please tell me what could be the problem? This pressure washer is almost brand new I have used it for only like 30 hours for 2 years that I have it. I used it couple times lately but same problem it works for 1 hour then it does not work any. I will


There are two common issues that will cause what you are describing. What you need to do is run the machine until it dies as you are describing. Then pull the spark plug and check for spark. If you do not have spark you have a failing stater. It is v ... Dewalt DPH3100 Gas Pressure Washer

Briggs and Stratton pressure washer will not start. I have a 6.75 hp pressure washer that is only a year old. when I pull cord it turns over but does not start. I changed plug and checked it, I have spark when pulling. I have 40-50 psi of compression when pulling also. gas was drained and is brand new. it was working fine last time it was used. I have tried starting it without the water line or spray wand hooked up and no difference. After about 10 or 15 pulls, can smell gas when I am trying to


Hello dave, the problem is compression to low,you need 60 to 130 lbs to run engine,check for blown head gasket,or bad rings,or a stuck open valve,hope this helps,, ... Briggs & Stratton Pressure Washers

I own a KUDS01FLSS3 KitchenAid dishwasher. The lights on the control panel do not come on and a cycle can not be started. There is about an inch of water in the bottom of the dishwasher basin and it looks like the previous cycle did not complete. I have checked the wall outlet that the washer is plugged into and the washer is receiving power from the wall. And ideas? My next thought was to take the door off and check the power supply running to the door panel and control panel.


Servtek06 writes:\015\012check connections @ control board/module. May be Control Board/Module. ... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

Vulcan Dishlex Executive 14-10 Dishwasher leaking onto floor from right hand side when it was filling at start of cycle. Husband has checked the following: both pumps (main and waste) hoses, solenoid switch (inlet). Where can we find the float/level valve? Could this be the problem? What else to check? This is the second time it's happened - I don't use it that much. The previous time my husband replaced the inlet and outlet hoses. What is the proper level for water fill - never above the


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. If you have water leaks around the base of your dishwasher,\015\012you may be using a detergent that is ... Dishwashers

Bosch SHY66C My Bosch dishwasher won't fill with water.  All electrical connections are fine and I can hear it make a sound as if it is trying to start about every 2 minutes.  There was water in the bottom so I used a shop vac and pulled it all out but it still won't start and is doing the same thing.  I checked the solenoid with a multi-meter and it appears to be working.  My power went out last night for about two hours and that's all I can think of that might have affected it.  The dishwasher


I'm a novice on this question, but i agree with the above statement about check the stuck float switch or check for a bad safety switch or lockout switch of some sort. I would suspect something is definately faulty in that area. Will the dishwasher r ... Dishwashers

We have an intermittent fault on our bosch dishwasher. It keeps cutting out mid cycle ....ususally leaving water in the bottom of the machine.....then sometimes..... hours later.... it will start up again by itself. We have checked outlet hoses and filters.


... Bosch 24 in. SHU43 Built-in Dishwasher

Cycle starts, soap box does not open. Cycle will repeat with water running for hours on end. No end to cycle or drying cycle. Checked inlet, outlet and tried reset.


Hello Paul,\015\012\015\012\015\012There are a few possibilities here but I really need a little bit more detail from you and you're going to need to do some testing to determine the cause of the fault - or faults. You're going to need a ... Bosch 24 in. SGS43C12 Classixx Free-Standing Dishwasher

Won't start I have checked the spark plug and I have good saprk. I have checked the fuel sysstem and the primer bulb injects fuel. I have removed the head and cjecked for engine damage and all cycle correctly. Vaves opne on time piston shows no dmagae. side walls are smooth and not damaged. This engine was working fine but the pressure washer needed some O rings replaced. I have tried to start it with and without the pump attahced. Evrything on the engine looks fine. I removed the spark plug and


... Briggs & Stratton Briggs Stratton 2550 Psigaspressure Washer

I have a Kenmore model 587.1610 dishwasher that doesn't fill all the way when starting a load. I checked the float switch and it is working fine. The fill soleniod is also working fine and is clean. It just seems to time out before it fills all the way.also to compound the problem it doesn't seem to want to start all the wash cycle even after I have re-started the machine and it has filled to capacity. please help thanks Danny


... Dishwashers

My pressure washer was running fine then bogged out.The person who lent it to me said dont worry about the oil it is fine, so i didnt check. I checked the oil and it was almost bone dry. So i filled it with oil but now it wont start, is it possible that the engine is siezed up or, can i get it running.


You probably helped destroy the engine. Honda's are great engines until they run low on oil ... Karcher 2500 PSI Pressure Washer

New LG 2131sh dishwasher, have it for 2 weeks, worked twice and now when pushing power lights come on, and when selecting program(eg intensive) it does not start. Water checked at it is fine. Checked door, closing fine.


I would call where you purchased it. There should be a one year warranty on the dishwasher and they should send someone out at no charge to repair it. ... Dishwashers

Hi, we have a Neff dishwasher and noticed a couple of days ago that it took hours longer than usual for the dishwasher to complete its cycle. Last night after the machine had been on for about 4 hours we checked and although there was some water at the bottom of the machine it had not started to wash the dishes although we had heard noises coming from the machine. On opening the integrated door notice that the "check water supply" indicator was lit up. Do you have any suggestions as to what


... Neff 24 in. S5443X2 Built-in Dishwasher

My Bosch diswasher water inlet work fine, when the wash motor or cycle need to start nothing happens. The timer is advancing normal. Water outlet(drain pump) is also working fine. There is no woosh sound (start of wash cycle) and arms is not rotating.


Hi,\015\012\015\012it sound's like the wash motor is either seized or just stuck, let's hope it's the later. Bosch had issued a service tip about this problem several years ago titled "Loosening Frozen Impellers" strange choice of word's considering ... Bosch 24 in. SHE44C02UC / SHE44C06UC / SHE44C07UC Built-in Dishwasher

I have a Maytag quiet series 400 dishwasher. I set the required buttons for a wash, inserted the soap in the soap tray but the machine will not start. Previously, when the washer would not start, I opened the door and pushed down on the soap tray and its seemed to fix the problem. Next time I used the machine, again not starting, but by pushing on the soap tray it would not start. Can you suggess what the trouble may be or give me a check list that I may do before starting the washer. This machi


... Maytag Dishwashers

I have a Whirlpool dishwasher mod. number GU2400XTP6 the clean light flashes then stoppes when the start button is pushed. the light on the start button flashes three times and stoppes then the clean light starts flashing again the machine dosen't start. I've checked the micro switches in the handle release and they are working fine. will I have to replace the main computer module? If so were do I get it and how much dose it cost?Thanks


... Whirlpool Dishwashers

We have a Beko DWD5410W dishwasher that has worked fine...until today - the 'wash' light is on but it is not wasing. I have pressed in the 'start' button and held for 5 seconds to reset and it then springs to life draining out or whatever that noise is, and then if I turn the dial to a setting (even the cold prewash) and press 'start' again it starts whirring away, then after about 10 seconds just stops, with the 'wash' light staying on. Not blocked, I have checked - this likely to be a frozen p


... Dishwashers

IDL700 wont start Kept getting error message to say there was a blockage. Checked all the pipes and pump, all fine. Now the blockage lights are out, but the machine wont start at all, just beeps when I press the start button, then nothing


Sorry to read about your problem, I hope this helps you out.the blockage, maybe inside the pump of the unit, or at the check valve.I suggest you contact a service company..I tried to help you. Please help me and Ra ... Indesit 24 in. IDL700 Built-In Dishwasher

I purchased my KARCHER G2500VH last summer. I used it one time for about an hour. I tried to start it today, seems like its not getting gas. I checked the gasline to make sure gas was flowing. I removed the sparkplug, poured a little gas into the engine through the plug hole. Replaced the plug, pulled the rope and it started for about two seconds. I also poured fresh gas in tank. Cannot get to start.


Have tried to start our BlackMax 2700psi pressure washer, it is not getting gas to the carburetor, what to do? ... Pressure Washers

I have a Bosch SHU43 dishwasher, about 6 years old. After starting a cycle, it will run for a while, perhaps 1/2 to 2/3 of the way through the cycle, then shut off. After 10-20 minutes it will start up again, run for a few minutes, then shut off again. It ends up taking about 12 hours for a cycle to finish. The problem started off somewhat intermittent and has gotten worse over the last few weeks. I've checked the electrical box in the front right bottom, and the connection is good. I've even


Hello,\015\012\015\012Welcome to FixYa.\015\012\015\012I`m not sure since you didn`t mention it or perhaps I just interpreted it this way, but is it consistent at the same time or approximately or is ... Bosch 24 in. SHU43 Built-in Dishwasher

I have a 4 year old Maytag MDBH945AWW and the panel lights come on and I can select cycles... but the dishwasher wont start. I tried holding the start cancel button, tried turning the breaker off for a couple of hours, took the inner panel off the door and checked the latch, but its still wont start. Any other suggestions? If it needs a new control panel its probably better to just get a new similar dishwasher for $300, correct?


What you need to do is read for continuity and power across the door latch switch. (2 white wires) AND 2 Black wires Both wires must read continuty at the control panel connectors to the power source terminals for the unit to start. Since the co ... Maytag MDBH945AWW / MDBH945AWQ / MDBH945AWB Built-in Dishwasher

The faceplate sometimes does not respond when I touch it, or if it does It may not let me cahgne the settings... Plus when the lights do come on the dishwasher won't start when I press the start button. When it does come on it works fine and has not had any other previous or current issues. Please HELP before I start whacking a hammer on this faceplate...


I also own a ADB1500AWB. The switch membrane failed within 30 days of purchase. It was replaced under warranty. The technician said this part fails very often. I bought an extended warranty. It failed again on 9/3. As of 10/13, the part is ... Amana 24 in. ADB1500AW Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1498 seconds