Having problems with your Miele 24 in. G646SC Plus Free-Standing Dishwasher ?

Dishwasher stops after 10 minutes inlet/drain light flashing

\015 Miele g646 sc plus -3 dishwasher stops after 10 minutes inlet/drain light flashing have checked all filters are clean checked discharge hose and water is being pumped freely when running dishwater tablet is still whole in its container\015

Answers :

I had the same problem on a 5 year old model. It was the main pump leaking from a perished seal causing the water protection microswitch to trip. This gives the symptoms you describe exactly. Parts cost from Miele was about £60 for a new seal. Fairly easy to fit.
1. Air gap / Drain hoses
If there is an air gap (located in\015\012the sink, near the faucet), check to see if it is clogged. Unscrew the\015\012top cap and see if there is anything blocking inside. Note: If there is\015\012no air gap installed, the dishwasher might not drain properly.
\015\012\011\011\011
\015\012If the drain hose is clogged, the dishwasher would not drain. If there\015\012is an air gap installed, it is very common that a hose going from the\015\012air gap into the garbage disposer is clogged. Remove and clean the\015\012hose. Make sure to reattach the hose before starting the dishwasher.
\015\012\011\011\011
\015\012\011\011\011Note: If you recently had a garbage disposer installed, it is common to overlook removing the drain plug.
\015\012\011\011\011
\015\012\011\011\0112. Broken belt
\015\012\011\011\011Some dishwasher models use a belt to drive the pump. Replace the belt if found broken.
\015\012\011\011\011
\015\012Note: Sometimes the belt would just come off the pump. Even though it\015\012might not be broken, it is recommended that you replace the belt,\015\012because it is probably too stretched out.
\015\012\011\011\011
\015\012\011\011\0113. Pump
\015\012Some models have two impellers inside the pump - one, wash impeller,\015\012takes care of the wash cycles, the other, drain impeller, drains the\015\012water out. If the drain impeller is broken (broken blades, shaft), the\015\012dishwasher would not drain. Replace any broken pump components.
\015\012\011\011\011
\015\012\011\011\0114. Drain solenoid
\015\012Some models (for example most GE dishwashers) use a drain solenoid to\015\012drain water out. Sometimes the solenoid gets stuck, preventing the\015\012water from draining out. Try to free up the solenoid. If unsuccessful,\015\012you might have to replace the pump assembly.
\015\012\011\011\011
\015\012\011\011\0115. Motor
\015\012\011\011\011If the motor is stuck, it is sometimes possible to free it up by manually spinning the motor.
\015\012\011\011\011
\015\012\011\011\011Replace the motor if defective.
\015\012\011\011\011
\015\012\011\011\0116. Timer
\015\012\011\011\011Replace if defective (note: uncommon problem).
Repair Help & Product Troubleshooting for Miele 24 in. G646SC Plus Free-Standing Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Hotpoint BC145 Dishwasher not cleaning starts to kick in but then just sticks on the "R" light flashing and cannot reset even after turning off. Itbeeps when pressing the select button sound weaker and shorter than they used to and the light does not move from the "R". On a couple of times I have tried it has reset and then the dishwasher starts but after about 3 minutes there is a low beep(not the usual beep when a programme finishes) and the washer stops and the light is flashing on the "R" ag


... Hotpoint 18 in. BCI45 Slim-Line Built-in Dishwasher

DISHWASHER STOPPING I HAVE A WHIRLPOOL ADG 7560/01 DISHWASHER. AFTER 4-5 MINUTES IT STOPS AND HAS A CONTINUOUS BEEPING AND THE START LIGHT FLASHES 4 TIMES THEN A PAUSE etc. I HAVE CLEANED THE FILTER LIFTED THE MESH AND CLEANED THE BOWL OF ANY DEBRIS AND WATER. I HAVE ISOLATED IT FROM THE ELECTRIC SOURCE LEFT IT FOR 10 MINUTES AND STARTED IT AGAIN TO FIND IT DOES THE SAME . LOST IS THE WORD THAT SPRING TO MIND. HELP!! MARTIN


... Dishwashers

Dishwasher cycle starts briefly for a couple of minutes and then stops again and the standard wash and eco wash programme lights are then flashing together? It appears that water is drawn into the appliance for a short time and it then seems to start and empty itself before the above lights start to flash, all within 3-4 minutes?


... Hotpoint 23 in. BFV62 Built-in Dishwasher

LIGHTS FLASH Hallo, I have a Indesit dishwasher (IDL 750) and the last few weeks there is a malfunction. After 15 minutes that the wash cycle 2) had started the dishwasher stops and the first and third wash cycle phase indicator lights flash, beginning from the right. Could you help me telling me the possible cause of this malfunction. Thank you in advance Fred Tourman Athens, Greece


... Dishwashers

I have Whirlpool Quiet Partner III dishwasher, Model number GU2400XTPS3, Serial number FS1820245. I recently had the thermal fuse replaced by an authorized service repair person. My problem is that the dishwasher stops mid-cycle. I noticed that when I try to clean it in the normal cycle, the dishwasher stops with about 46 or 47 minutes remaining, and the green light flashes continuously. I have pressed the Normal and Heated Dry buttons, as well as the Sani Dry and HEated dry buttons to reset the


... Whirlpool GU2400XTP Built-in Dishwasher

I have Whirlpool Quiet Partner III dishwasher, Model number GU2400XTPS3, Serial number FS1820245. I recently had the thermal fuse replaced by an authorized service repair person. My problem is that the dishwasher stops mid-cycle. I noticed that when I try to clean it in the normal cycle, the dishwasher stops with about 46 or 47 minutes remaining, and the green light flashes continuously. I have pressed the Normal and Heated Dry buttons, as well as the Sani Dry and HEated dry buttons to res


... Whirlpool 24 in. ADG7540 Built-in Dishwasher

The dishwasher is flashing error 20. The wash cycle begins to work but after a few minutes the wash cycle will stop and the light flashes on the program selected. We have tried turning the dishwasher off from the switch to no avail. Please advise us on what we can do to fix this.


... AEG 24 in. Favorit 3A Free-standing Dishwasher

Dishwasher stops after 10 minutes inlet/drain light flashing


I had the same problem on a 5 year old model. It was the main pump leaking from a perished seal causing the water protection microswitch to trip. This gives the symptoms you describe exactly. Parts cost from Miele was about £60 for a new seal. ... Miele 24 in. G646SC Plus Free-Standing Dishwasher

Dishwasher Whirlpool ADG7540. Does not complete cycle. Approx 20 minutes into cycle dishwasher appears to get stuck on rinse.The water is cold. Machine stops and makes a constant beeping noise and the green light flashes 3 times repeatedly.


... Whirlpool 24 in. ADG7540 Built-in Dishwasher

Bosch SHE58C05UC/50 dishwasher stopped at 96 minutes (will not advance) & I cannot cancel. Diagnostic codes C4 then P0, rinse light steady on, drying light flashing. No water in anti-overflow pan, it's dry, float switch is working. Vacuumed out any/all water, Have replaced water inlet valve. Main circuit board shows no sign of solder joint disruption. Have switched circuit on, then off in attempt to reset (negative results). Any ideas on how to reset and then to fix the problem?


... Bosch Evolution 800 SHE58C05UC Stainless Steel Built-in Dishwasher

My candy cfd612 dishwasher stops after a few minutes working the pre wash light and the wash light flash at the same time any ideas?


... Dishwashers

Hoover HEDS 668 dishwasher all four lights flash and beep whilst the machine drains, after a couple of minutes the beeping stops but the four lights glow. Cannot reset to cancel. Also still makes draining noise whilst the door is opened. There is no water at the bottom of the machine.


... Dishwashers

Hoover HEDS 668 dishwasher all four lights flash and beep whilst the machine drains, after a couple of minutes the beeping stops but the four lights glow. Cannot reset to cancel. Also still makes draining noise whilst the door is opened. There is no water at the bottom of the machine.


... Dishwashers

My Miele G2430 dishwasher stops right after draining in the first minute or so after starting, and the intake and drain light comes on. The solenoid at the end of the intake hose then clicks and the light begins to flash. I applied suction to the intake hose to determine if the solenoid is working, and the valve does open and close. There has been no error code displayed. I cleaned all of the parts and filters referred to in the owner manual.


For a drainage fault heres what the miele service manual says for your machine\015\012Water present in appliance and is not being drained off. The display shows Drain fault F11. The buzzer is activated for 2 minutes. ... Miele Optima G2430SCi Stainless Steel Built-in Dishwasher

Hi I have an F&P DW691 dishwasher (manufactured by whirlpool) the reser light is permanently giving two quick sucessive flashes and will not start the machine unless held on for 6 seconds, the machine then starts for a minute then stops and goes back to the two flash reset problem. Does any one know the fault code applications for this model.thanks Mike


Hi, I've got the same dishwasher but with a different fault, there's power down the cable to the d/w but no power lights on the front panel?Thanks. ... Fisher and Paykel Dishwashers

Hi have a Dishlex Global 450 dishwasher which stops after about 15 minutes into the cycle. The is nothing flashing and no lights it just go off totally. There is water in the bottom of the dishwasher. help please


... Dishwashers

I have a Whirlpool ADP6515. It's been working fine for about 2 years now but recently cycles are not completing properly, it can run for 30-40 minutes depending upon cycle. The start light is flashing a 4 times repeatedly, I think this happens when it moves from a wash to a pump cycle but not sure. We have to hold down the start button to force it to go to the end of the cycle and the the lights stop. If we do that we can then use the dishwasher the next time, but only after we force it to go to


While replacing the console board, the replacement should be of same version. The boards are using programmable IC. Hence matching the software version is a must. Only the manufacturer or his authorized provider can help regarding t ... Whirlpool Gold 24 in BuiltIn Dishwasher w Adaptive Wash Cycle 24 in Builtin Dishwasher

Fast flashing dishwasher starts ok, then stops after a few minutes with the ''fast'' light flashing. It does not matter what cycle its on, the same result occurs.


The outlet pump could be triggered because the "anti flood device" polystireen float and micro switch at the base of the washer has detected a water leak from a leaky hose or water spil) This device automatically puts the pump out motor on and stops ... Dishwashers

ADP5550 DISHWASHER RINSING LIGHT ON, START LIGHT FLASHING TWICE, BUT STUCK WILL NOT PROCEED WITH THE WASH. I HAVE PRESSED THE START BUTTON FOR 10 SECS, 30 SECS BUT THE ONLY RESPONSE IS THE PUMP ONLY RUNS FOR A FEW MINUTES AND STOPS.


This does sound like a problem with the "anti-flood" device that does detect water (leak / spill) at the base of the washer. This device is a protection device that consists of a polystirene float and a micro swithch. Once a water leak od spill is de ... Whirlpool 24 in. DU920PW Built-In Dishwasher

I have a kichenaid kuds03ftpa dishwasher after start it stops after several minutes and the start light flashes. When i open the door, there is water at the bottom. So i press cancel and the water drains out. Then i restart the dishwasher and it does the same thing.


... KitchenAid KUDS03FTPA Built-in Dishwasher

Hi my Servis M4905 Dishwasher has stopped working properly, when you set the programme and close the door it seems to start its cycle but after a few minutes it stops all the lights come on except the first one which flashes on and off. The other day it tripped the electric. Do you think it may be the module which has gone faulty


... Servis Dishwashers

Hoover HED 6612/1-80 dishwasher all four lights flash and beep whilst the machine drains, after a couple of minutes the beeping stops but the four lights glow. Cannot reset to cancel. Also still makes draining noise whilst the door is opened. There is no water at the bottom of the machine


Not sure if you have got a user manual for this dishwasher. You can download one from this site.\015\012\015\012You have a flood situation ... Hoover Dishwashers

Dishwasher runs but stops after 20 minutes with green flashing light.


... Kenmore 24 in. 17032 Built-in Dishwasher

Delonghi dishwasher Dw28w flashing lights. The dishwasher stops halfway though cycle and stops and flashes the Last 2 lights, the wash and drying light


... Stoves Dishwashers

Kenmore dishwasher, model 665.170 344 01. "Clean" light keeps flashing and will not stop. Have tried everything in the manual and the light still will not stop flashing.


Only reset you can do is unplugging power cord for 10 minutes.The control panel it is probably faulty and in need for replacement. ... Kenmore 16602 / 16604 / 16609 Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2225 seconds