Having problems with your Miele 24 in. G646SC Plus Free-Standing Dishwasher ?

Inlet/drain light remains on

\015 Have followed the intruction ooklet, turned the dial to stop turned the machine off and then on again. Checked the flow of water intake, is normal.Cleaned the filter and beneath that taken the non return valve out and washed out, no kink in the hose. I feel that it might be something to do with the inlet hose, after opening the casing on the filter it appears to be full a dark green molded colour (it maybe it is suppose to be like this). The pump sounds to let the water out of hte machine, so I don't think there os a blockage. If there are any ideas please let me know, otherwise will have to scrap it, which is a shame.\015

Answers :

I have the same problem on a Miele G647 SC Plus. It starts and completes the wash cycle, might skip a final rinse - not sure, but it drains the water. Pump then continues to run for extended period then inlet/outlet\015\012light comes on. The dishwasher never moves to the drying cycle.

I cleaned all filters, checked supply/drain hoses + the non return valve. All\015\012seemed servicable. But no real improvement in fault.

Any way I can fix this?
My G647SC PLUS has had the same symptoms with several week intervals. Now finally solved. Unplug the machine. Take off the metal front plate at the bottom of the machine - first remove the plastic cover under the door near bottom, two size 2 Pozidrives, then you get at the steel cover, again two size 2 Pozidrives, a bit harder to get at, you may have to lower the door. After removing the screws, gently lift the cover from low edge and it will come off. If the well under the machinery is dry, check the float sensor which is the white round flat-bottomed device near the front by removing the plug cover, the plug itself and finally the float sensor itself. Open it by releasing the two catches and check that the microswitch is not permanently activated by the styrox floating device. In my case it was, probably the styrox had lost some of its form but I managed to reinstalled it in such a way that it released the switch. I checked that by lifting the styrox the microswitch activates. Re-installed and run the machine, works fine now.

If the well is wet, then you have a leak in the draining system and need to replace the gaskets and/or the pump itself.
Repair Help & Product Troubleshooting for Miele 24 in. G646SC Plus Free-Standing Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Whirlpool dishwasher gu3600 The pots & pan, normal light and delay lights flash all the time. Also the time remaining screen has two horizontal lights on. The dishwasher won't start


... Whirlpool Dishwashers

I have a Whirlpool model GU2400 Whirlpool Gold dishwasher and it will not start. There are no flashing lights just dashes across the time remaining box. I tried to push hi temp wash/heated dry 3x but it only allows me to hit it twice and displays 88 in the time remaining box. Then it says d3 in the time remaining box. It will then start running a drying cycle for 12 minutes. If I push cancel it won't do anything. I have to hold in cancel for about 30 seconds and it will drop down to 6 minut


... Whirlpool GU2400XTP Built-in Dishwasher

Water softener Salt residue remains on the dishes. The water softener is going throught salt like crazy. I fill the salt and make sure that the light is off before I start the cylce. Within the first 20-45 mins the salt light comes on again and the dishes will not wash properly. We have come to the conclusion that the salt is being distributed to quicky but cannot figure out why the light keeps coming on. The switch inside the cap for the salt is set a the min.


Just a thought, I hope the lady did not use table salt :-) ... Danby 17 in. DDW1802W Designer Series Built-in Dishwasher

I have a maytag mdb6650 aww dishwasher. The dishwasher just stopped. The light on the control panel is on. If I push the buttons to try a different cycle, the light over light wash remains lit, so the buttons don't seem to respond. I was wondering if it is the control assembly, or if the door switch is not working. The handle cracked a while ago, but if the dishwasher still worked even though the handle had cracked in half.


... Maytag 24 in. MDB6600A Jetclean II Built-in Dishwasher

I have a Gallery 900 series GLDB958AS dishwasher. The cycle status lights (just right of the "time remaining" status window) continually blink. None of the buttons on the front panel work and every 10 minutes or so the water pump starts up for about a minute then shuts off. No water enters the dishwasher. I tried turning the power off then on but there is no change. Every so often a random cycle light will blink or light up for a minute, then turns off.


It seems that there is error on the program controller unit. All you need to check if that if there is moisture build up on the panels thus causing the programs to go harewire.\015\012So remove the panel and disconnect the wires, check all lead ... Frigidaire 24 in. GLDB958A Energy Star® Built-in Dishwasher

Replaced circuit board on my kenmore 665.13742k603 dishwasher,still all wash buttons,and start button will do nothing.ran test using sani rinse and heated dry buttons all lights come on but washing light does not,all lights remain on after test,unplugged,plugged back in,,still no wash buttons or start buttons work,can you help?


... Dishwashers

We have a kitchenAid dishwasher -- just installed last year new-- we cannot get the rinse aid low light to go off. We have filled it up to where it can no longer hold anymore and the light is still on. I have tried to cut the power on/off and it still remains on. Any suggestions on how to get the light to go off? thank you.


Check to see if the "Heat Dry/Lock" button is lit up. If it is, press the button and hold it for four seconds to unlock your dishwasher controls.Close your dishwasher door firmly and press the "Cancel" button. Wait two minutes for your Ki ... KitchenAid Dishwashers

The control panel on my Electrolux/Icon dishwasher is not working. The only light showing is the red start/cancel light. When I press it to start, nothing happens and the light remains red. What could be wrong?


... Electrolux EDW5505ESS Built-in Dishwasher

Bosch SHE43F02UC/50 Lights on, but won't start any cycle....Regular Wash light only one on with timer showing 188.....pushing other buttons does nothing.....no noise, no water fill, just those two light remain on and nothing happens?


... Bosch Dishwashers

Dishwasher Normally, after the dishwasher cleans the load, it displays green light next to clean. Once the door is opened, the light goes off an dishwasher is ready for next load. But from few days, after opening the dishwasher door, the clean light does not go off, it remains lit. Dishwasher doe snot reset for next cycle. So, I have to go in the basement and trip the main power to dishwasher. That resets the dishwasher. This needs to be done before each cycle. Not sure how to resolve the issue.


Make sure that you do not open the door during the wash cycle. Wait until all the cycles \015\012are complete before opening the door. Especially don't open the door \015\012during the drying cycle. ... Dishwashers

Time remaining light has 2 dashes and the normal light flashes


... Whirlpool GU2400XTP Built-in Dishwasher

The dishwasher did not complete a cycle. There is soap still in the opened dispenser and soap on the dishes. The clean light keeps blinking. Usually the light remains on when the cycle is finished. I tried to restart the dishwasher and it won't do anything.it is less than two years old.


Hi, \012I have an older dishwasher also and recently mywife also complained about it not cleaning right... so me being the man I amtried in vain to clean the things... Bought new spray arms online and installedthem in minutes...now the thing works li ... Dishwashers

Kenmore Dishwasher, 66517029401. Lights on control panel will not light up & water remains at bottom from recent load just completed.


Are you sure the breaker that runs it didn't trip? ... Kenmore Dishwashers

Error code Hi My FDW60 IS FILLING AND THEN FLASHING TWO LIGHTS THE FAST 40' AND THE DELICATE 50' AND THEN EMPTIES BUT THE LIGHTS CONTINUE TO FLASH AND THE MACHINE REMAINS IDLE. IS THIS A FAULT CODE? MANY THANKS


Hi, did you ever manage to fit a new eliment and how hard was it??! Thanks in advance... Sure it has dies since too! ... Hotpoint 24 in. FDW60 Free-standing Dishwasher

We had a power cut. When it was over the dishwasher continued and finished its wash cycle. The lights on the control panel, on/off and wash cycle indicator lights did not work during the remaining part of the cycle and will not work now. The dishwasher is a Hotpoint, mod. LFT 114 UK


... Hotpoint Dishwashers

I have a Frigidaire dishwasher (FDB2810LDC1) and a Er code appears in the display with the sensing, rinsing agent low, sanitized, and clean lights all flashing as is the child lock light. After seeing the Er code, I opened the dishwasher and thought I heard the detergent tray open but most of the detergent was gone with a little remaining. This has happened before and we have had the electronic panel replaced twice. Could it be something else like something blocking the detergent tray from op


... Frigidaire Dishwashers

Miele Inspira G2180 SC SF dishwasher problem We start the Normal cycle and after the dishwasher fills up with water the units starts beeping, all six program lights start to flash, and the water drains out. The lights remain blinking. What might be the problem please? Dan


... Dishwashers

The glass xpress light on my Whirlpool GU 2400, Quiet Partner III, is flashing. I tried alternating the sani rinse and heated dry buttons, and alternating hi-temp wash and heated dry---nothing changed. None of the option buttons light up when they are pushed. and the time remaining stays on -- (two dashes), the dashes don't move. Any other ideas?? PLEASE


... Whirlpool GU2400XTP Built-in Dishwasher

My power was out in my home briefly while my hotpoint bfv620 dishwasher was running. Once the power returned the washer's indicator lights 2 & 4 were flashing. I've tried reseting the machine, turning it off and back on and the lights remain flashing. Any thoughts?


Turn it off and give it more time than before then put it back if the flashing continues then remove the water out of the hose and check that the hose isnt blocked, check the pump if blocked , then it continues that means may be the suppply surge m ... Hotpoint Dishwashers

Greetings, My Viking disk washer Model # Dfud042 runs 4-5 min then makes several cliking sounds and stops. The program light for the light china is blinking, the soap dispinser still has soap in it, and water remains in bottom of the washer. Regards, James Parker


Hi,\015\012If it is filling and draining ok, then I suggest the problem lies with the main heating element.\015\012Disconnect from the supply and turn off water. Pull forward, to gain access to the element from underneath.\015\012Te ... Viking DFUD042 Built-in Dishwasher

My Frigidaire Model FDB2810LDC1 dishwasher will not stop running. Seems to complete a normal cycle and different cycles can be selected with normal time countdown but at end only rinse agent low light remains lit and sounds as if pump is still running. If opened, water appears to be streaming from rotator arms. Have cycled power but symptoms remain.


... Frigidaire Dishwashers

Check water light stays on rendering machine unuasable.checked water supply.all filters .googled problem told me to switch water supply on and off rectified problem for 10 minutes then check water light came back on. water remains in bottom of appliance.


... Bosch Dishwashers

Baumatic Dishwasher BDW5 - All the control lights remain ON


All lights staying on machine stopped ... Baumatic 23 in. BDW5 Built-in Dishwasher

Bosch SHE4AM16UC/05 dishwasher will not operate, lights for "Clean" and "Autowash" remain on. Can turn on and off, but that's it. Tried reset, turning it on and off from the breaker, checking dr


... Bosch Ascenta SHE4AM16UC Full Console Dishwasher - Black

I have a Kenmore Type 575-0 Dishwasher, model number 665.16033401, Style 16033. It runs trough the cycle, once the cycle is complete the clean mode light is on but most dishes are still dirty. I had someone here to repair this about a year ago. All he did was press alternating two buttons, which I have tried, it resets and lets you start a new cycle. However, the problem remains. Last time there was only button pressing involved, no need to replace anything. So, I would hate to have to pay ag


You need an electronic control and heating element ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0806 seconds