Having problems with your Miele 24 in. G646SC Plus Free-Standing Dishwasher ?

G 646 sc pump still runs when programme is off

\015 Also red light on\015

Answers :

Hi,
I had the same problem, the drain pump kept working even on the off program. After a little investigation i found out that there is a leak sensor that triggers the drain pump continually until it does not "sense" water anymore.
Firstl i tried to open the rear panel with no success.
Next i tilted the dishwasher to the left and let all the water drain out, plugged the dishwasher back to electricity and it worked!!!
I hope it will help you.
Repair Help & Product Troubleshooting for Miele 24 in. G646SC Plus Free-Standing Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a Bosh Logic dishwasher SGS65L12GB/04 The other day it got to 1 min left and would not stop pumping out water and continued even with the door open. After 5 mins playing around it started working again for a further 2 washes. Now when switched on the pump for pumping out the water works continuously. Reset it time seem to count down but does not do anything reset time goes to 0 and beeps but still the pump runs even with the door open. all buttons seem to work fine but no washing and pu


Hi Jonathan,\015\012\015\012Welcome to FixYa.\015\012\015\012Your float may have got stuck or it's possible that you have water leaking into the bottom of the washer. In the bottom of the wash compartment, next to the drain yo ... Bosch Dishwashers

Asko dw20 pump keeps running even with door open and turned off... The machine got to the final cycle then the pump just keeps running and the glass icon (L2) keeps flashing. All the water is not evacuated from the washer. When I power off from the front the drain pump still runs (and water is still not draining). When I power cycle from the mains (waiting 10 seconds) the pump engages again and the water level drops a bit and then stops draining. I have done this until all the water is empty an


... Asko Dishwashers

G 646 sc pump still runs when programme is off


Hi,I had the same problem, the drain pump kept working even on the off program. After a little investigation i found out that there is a leak sensor that triggers the drain pump continually until it does not "sense" water anymore.Firstl i tr ... Miele 24 in. G646SC Plus Free-Standing Dishwasher

Whirlpool ADG7540 approx 4 years old (maybe a bit older) I have ran diagnositic check and the start light flashes 4 times stops briefly then flashes 4 times again over and over along with a continuous bleeping. When I put the dishwasher on any program I can hear the pump running but after a few mins the same flashing and beeping occurs although it sounds as if the pump is still running. I have taken off the pump checked for blockages and also checked the outlet hoses and spiggot, there are non.


Yikes, we have just identified this exact same problem tonight. If you've had any success with fixing it, we would sure appreciate hearing how. Best of luck with your machine ... Whirlpool 24 in. ADG7540 Built-in Dishwasher

Zanussi Dishwasher (Table Top) DCS 12 W Machine it stuck ON with the drainage pump running and all lights OFF. Pump is still running when the door is opened. What do I need to do. I have unplugged the dishwasher from electric to shut it down, but when electric is turned back on the pump keeps going. Help.....Dave


... Dishwashers

Candy CDi 454-80 e4 error code, all water seems to be pumped out but pump still running, pump start to run when switching the machine on and e4 appears


... Dishwashers

LG LDF6810ST had OE error. Disassembled found no obstructions blew air through and vacuumed hoses to air gap and to disposer, no obstructions. Never heard pump run when starting cycle, so replaced drain pump. Still doesn't run. Looked at the service manual, and the only other suggestion is repair circuit? Is this the circuit on the bottom right of unit or the pcb up top? Wires and connections all look fine. What else could it be. Any suggestions appreciated!


Hi,Usually my First Response to this Common Error is :-Most likely pump trap is clogged up. Access it behind small door at front. Drain water out through small hose that is there otherwise water will be all over the floor when ... LG LDF6810ST Stainless Steel Built-in Dishwasher

Bosch SHU43C My Bosch SHU43C is stuck with the drain pump running. I ran the self-test and it gave me the fault code 4 wich indicates a filling fault. The washer is empty and all wash cycles display the correct number of minutes for the cycle. It counts down to 0, but the pump continues to run. Does this indicate a stuck float, or is the problem with the control board? Where is the float located? Are diagrams/pictures available on-line anywhere? I've done some searching, but haven't found any. R


My SHU43C is just over 3 years old. I had a similar problem recently. First, there were a few floods. Then, the Bosch only drained non-stop. Even when I used the Cancel Drain buttons the drain pump would run without stopping. When I ... Bosch 24 in. SHU43 Built-in Dishwasher

Candy washing machine runs through programme and stops at the point where it drains the drum to start the spin. Have switched it off and turned timer to correct position and it drains and spins OK (1200 spin) Tried other programmes on timer but same thing, stopping at point where the pump drains and the spin starts. Have checked the pump and is OK any ideas please, I am quite capable of taking the machine apart for repair. Thanks in anticipation Pete


... Dishwashers

Pump is constantly running - trying to pump out water, although there is no water in the tank. This condition remains the same AT EITHER AND ANY reset positions of buttons ABC or programme buttons. Programme END indicator is NOT lit, LOW SALT indicator lamp is ON, LOW RINSE-AID indicator lamp is ON. No apparent blockages. Supply water water is on and free flow.


Hello, welcome to FixYa.\015\012\015\012Based on your description it sounds like the emergency overfill switch has been actuated.\015\012\015\012Here`s what to do and what to look for. ( unbeknownst to many this is built by B/ ... Neff 24 in. S5543X2 Built-in Dishwasher

Miele G 870 SC dishwasher had blocked drainage due to stopped up sewer which got snaked out by plumber. Ever since, the drain pump won't stop running. Have cleared the trap, filter, and drain-filter and still the pump runs continuously.


Hi\015\012\015\012The problem is with the float switch mechanism located at\015\012the bottom of the unit...either this has gone bad and should be replaced or the\015\012pump itself is bad & should be checked. Hope this helps...please pos ... Miele 24 in. G870 Built-in Dishwasher

I have a similar problem to another person. The drain on the dish drawer was blocked. The unit now shows an F1 error code ( flood?) and the pump runs continuously even after I've unblocked everything. I've tried switching it off for ages and drying everything out. When I switch it on again it shows the wash programme but then reverts to F1 and the pump motor runs continuously. Any ideas to cancel the F1 code?


The flood sensor on this unit is a PC board in the base, so you would need to remove the lower drawer and dry it out under there. If the base is dry and you still have the error, you can take a look at that sensor and clean any corrosion/minerals off ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Maytag Dishwasher Model MDB4100AWQ When I start the Light Wash Cycle: Washer fills with water, heater comes on (I checked it with a volt meter--120 volts), timer runs, motor never runs, before the timer gets to "rinse" the heating delay light on the door comes on and the timer stops. The heater is still on (120volts) nothing further happens it just boils away on the water in the washer. Note: If I manually forward the timer to "rinse" the motor will kick in and run but does not pump out w


Most common d/w power is 120 volts, check for 120 volts with a  ... Dishwashers

Hi ..I have an Excell gas pressure washer model no. Exwgv2121-3 with Faip 2100 psi 2 gpm vertical shaft pump..the problem is that there is water leaking from every weep hole at the bottom of the pump when running. Oddly enough,the pump still puts out significant pressure but less than it should due to the leaking water. What is the most likely cause of this?..is it the high pressure water seal(s)? If so,how do I repair it?


... Pressure Washers

While using my B&D PW 1600 power washer, the unit started to cut in and out. I thought that it might have overheated, but it had not been running 20 minutes. After letting it sit for 10 minutes to cool, the pump will not run. It has now sat for over an hour, unplugged and still will not run. Any suggestions? Tony [email protected]


A valve where to hoses are connected to maybe plugged up Here is a video on how to repair it without spending a dimeThe video is for a different brand although all have the same valve to make these pressure washers to operate ... Black & Decker Pressure Washers

I have a NEFF Built in dishwasher S5453 X1 which wont complete programme, water pump just keeps going, pumping dry. I have turned off and also used reset buttons but each time as you switch on Pump keeps running


... Neff 24 in. S5453X1 Built-in Dishwasher

Whirlpool model DU960 - from 2001, I think. Stopped running mid-cycle and the cycle lights flash. Won't run. How to fix? If I press 'Cancel/Drain', it flashes that button light. If I press one of the wash cycles again, it turns on the pump for about 1 second, shuts off and the lights flash again. I tried turning off the circuit breaker and turning it back on, but it still won't run. Is this fixable? Do I need to call for service? Or, would I be better off just replacing it?


I have a whilpool du960 the rinse only light is flashing and the light wash light is also flashing. ... Whirlpool Dishwashers

Bosch SHU43 Dishwasher runs full cycle to 0 but circulation pump never shuts off.


... Bosch 24 in. SHU43 Built-in Dishwasher

I have a Generac pressure washer, model #01450-0, with a Honda 5hp motor. The motor runs fine, but the pressure hose pulsates as if the pump is intermittently making pressure, and the pressure out of the sprayer is about half of what it should be. A friend suggested replacing the seals in the unloader. I bought an unloader kit, replaced everything and it still runs the same. It will build a small amount of pressure, spray for a few seconds, then the pressure dropps to almost nothing. Any help ap


Take a small diameter wire and poke thru the discharge hole of the spray head to clean out.\015\012Second time in 6 months that I had the same problem. The problem is alway in the spray head. ... Pressure Washers

E1 fault code Dishwasher runs for about 5 minutes. Water fills up at bottom of unit and then machine seems to pause then fault code E1 appears then water is pumped out from bottom of machine. There are no leaking pipes and drain is installed correctly. I installed a new wash pump and fault still appears.


Hi,\015\012I think both the heater and thermostat / trip switches need to be checked.\015\012If water is going in and out ok, then it seems to be waiting to heat the water. It sees a fault - so just clears out.\015\012Heating elemen ... Dishwashers

Stops part way through programme water still in machine. Now no power to machine. Problem happened yesterday - cleaned filter and pump - power came back. Programme started but then stopped. No power - nothing happens.


Either there is a bad capacitor in the control panel, or the power supply has a faulty capacitor. You will have to get a multi-tester and test each component for resistance and current ... Dishwashers

Hi I have a siemens hi line, the door was forced closed and it is not working properly since, the motor is still running and the programmer are still working, so would replacing the catch fix the problem?


... Siemens 24 in. SE25A836GB Hi-Line Free-standing Dishwasher

Bosch SHE55M06UC dishwasher pump was running beyond the cleaning cycle and produced a burnt rubber/plastic smell. Unit did not work until I tried the diagnostic mode, then it seems to run fine but still smells of burnt components.


... Bosch SHE55M06UC Built-in Dishwasher

Have a Whirlpool Model GU1200XTLQ3 that makes this God awful noise when running. Did what your post said about cleaning the chopper and found glass. Replaced it back and I'm still getting the noise. Is there a way to check the pump from inside. In other words, if I take the chopper back is there a way to check out the pump


... Whirlpool Dishwashers

I have a Honda ,gas powered power washer and when I squeeze the handle the water pump kills the motor. I've let the engine run until warm and it still can't take the water pump engaging. It's a three year old washer.


... Pressure Washers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1143 seconds