Having problems with your Miele 24 in. G656SCi Plus SS Built-in Dishwasher ?

On the MIELE G881 SCI plus -3 the cycle stops after about 2-3 minutes (enough time to purge the remaining water and fill the dish washer with new water). Then after 10 minutes it abandons de cycle and shows the red light "intake - purging". When i open the washer, the water inside is NOT warm.


Answers :

Hello, Welcome to FixYa.

I'll start by saying on many Miele different issues can manifest in a similar scenario, water valve, leaks, etc. and then the error lights.


This particular error according to Miele indicates the inlet valve has failed or is possibly blocked (or at least partially blocked) thus dropping the inlet psi below the minimum allowed tolerance of 4.5psi

That being said, it can also indicate the valve or some other component (error codes are not foolproof, they are simply "clues" to what to look for) is leaking water into the base pan/overfill tray and activating the safety float/waterproof system.

**Turn off tor disconnect he power supplying the diahwasher before servicing unit...safety first**

If you can remove the lower toe panel/access plate, you should be able to confirm or dismiss any presence of water in the base pan, thus eliminating that possible scenario and moving to other possibilities.

The next step is to investigate the possible water inlet valve blockage/restriction. You will need to turn off the water supply to unfasten the supply at the dishwasher valve. Check the screens for any debris which may cause complete or more likely partial blockage and clean/remove if present.

Check these things out and we can go from there. I'll await your next post.

If this resolves the issue I Thank you for choosing FixYa for your inquiry and hope you will take a moment to rate the information I provided in an effort to assist you.

Regards,

Macmarkus :)

Hi
\015\012
\015\012Intake/Drain light flashing means an issue while\015\012draining. You would need to check for air gap on the dishwasher, it may be\015\012clogged. It prevents dishwasher from draining, sometimes the drain flow is\015\012restricted due to gunk. Cleaning or bypassing the air gap will resolve the\015\012issue. If this doesn't resolve the issue then it is due to seized (or stuck)\015\012drain pump. Disconnect the power to the dishwasher or turn off the breaker to\015\012the dishwasher. Tip machine on its back; remove screws that hold the bottom tray\015\012on. Remove the hoses to the main motor, remove electrical connections &\015\012remove motor (single screw holds motor, it is on the outside back of the\015\012machine). Try to rotate the motor (use WD40 is necessary). If you cannot rotate\015\012it, then motor will be required. If the error still appears then cancel the\015\012error message, turn the rotary selector switch to "Stop/End" or press\015\012the "Start/Stop" switch for approx. 5 secs. Switch the appliance off\015\012and then back on again. Hope this helps... Please post back if you need more\015\012information.
\015\012
\015\012Daniel

Repair Help & Product Troubleshooting for Miele 24 in. G656SCi Plus SS Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

On the MIELE G881 SCI plus -3 the cycle stops after about 2-3 minutes (enough time to purge the remaining water and fill the dish washer with new water). Then after 10 minutes it abandons de cycle and shows the red light "intake - purging". When i open the washer, the water inside is NOT warm.


Hello, Welcome to FixYa.I'll start by saying on many Miele different issues can manifest in a similar scenario, water valve, leaks, etc. and then the error lights. ... Miele 24 in. G656SCi Plus SS Built-in Dishwasher

Our MIELE TURBOTHERMIC shows a red indicator light on the topic of: drain/watersupply.when switched off and restarted, it evacuates the water succesfully and commences the cycle but then after two minutes, it stops again with the same message.


Hi,First the unit drains and then fills with water. When the unit has intially drained open the door and manually fill the unit with water, about 5lts. This will then allow the dishwasher to go to the next step which is to circulate the w ... Miele 24 in. G656SCi Plus SS Built-in Dishwasher

My built in Whirlpool adg 9340 washer won't start a cycle at all. It seems to start a cycle and after 1 minute it stops and it starts beeping. Also water remains on the bottom. As soon as the cycle starts it drains that water and brings new water in which stays there. It won't work for more than 1 minute....


... Dishwashers

My dishwasher SL34A015UC / 29 does not complete it's cycle. The cycle will stop with 1 minute left in the rince cycle and continue to run for hours, showing just one minute left. The dishes are not geting clean and there is a unplesent odor inside. I can hear the water draining during the cycle. The drain line is clear and there is plenty of water in the dishwasher. Any thoughts?


... Siemens SL5A70UC 24 in. Built-in Dishwasher

Hi Dishwasher BOSCH SMS53L02GB start of program digital display shows all sensor working. Water not pumping in. All hoses and filters checked OK Machine pumps water out then completes cycle in 1 minute. Water supply getting to base of machine An E21 code shows up on fault finding cycle


... Bosch 607335 Water Valve Assembly For Dishwasher

I have a kenmore Ultra Wash Dishwasher, Model 15825691. We were recently hit by lighting. Once hit, the dishwasher started up. Since then, all cycles work, however, at the end of any cycle, the dishwasher continues to run and fill the bottom of the washer up to about two inches and then cuts off, so when we open the washer, there is approx 2 inches of water inside no matter what. I have pressed the "Cancel/Drain" button, in which drains the water after two minutes, but when that is finished, the


There must be a problem wit the fill valve. Check which valve the water enters. Check first the wiring to the valve of the water inlet or where the water comes out to fill the washer. Check for physical evidence of damage on the solenoid (or contr ... Kenmore 24 in. 16539 Built-in Dishwasher

It appears to finish it's cycle, as far as the dishes are clean - however there is clean water that has pooled on the bottom. you can hear the water fresh coming in - the pump comes on for a few minutes, drains some of the water and shuts off - the pump comes on again - drains some of the water and turns off. I turned the water going into the dishwater off - the pump ran for a few minutes - drained some of the water and then just sits there with the red power light on - there is still the same


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. Dishwasher not draining properly or not draining at all issues\015\012can arise due to different reasons ... Bosch 23 in. SHU3302UC Built-in Dishwasher

Cycle begins and we can hear water filling up, but the arm doesn't spin, and water isn't being "sprayed" around the washer. We can hear the dishwasher "clicking" throughout the cycle, but nothing else is happening, and about 10 minutes through the cycle water just comes pouring out the bottom of the door. There is a bit of a burning smell as well.


... GE Profile PDW8600J Built-in Dishwasher

When I start the top drawer it defaults to 5 minutes (with the lights Heavy, Fast, Rinse highlighted) runs for a couple minutes, then stops and the LED starts randomly cycling through all kinds of codes very quickly. There is water in the tub that has not drained after completing the couple minutes of operation. This cycle repeats itself if I hit the power button again after the LED starts freaking out. The 5 min cycle shows in the LED, sometimes with the no circulation error, sometimes with the


Here is the solution: \015\012http://applianceguru.com/forum1/24814.html ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

When I press the start button, Bosch dishwasher (model SHY56A 05UC) just keep running the motor pumping the water out of dishwasher, irrespective of: 1) the wash cycle it is on, 2) whether the door is closed or open, 3) whether I cancel drain cycle, as told by Bosch Cust Svc in following steps: - "Cancel Drain" by pressing 'Quick Wash' and 'Regular Wash' buttons together for a minute until it shows 0* - Shut power off for a minute and wait for a minute - Restart on Quick Cycle. Paid


What is happenig i believe and has happened to me 2 times is that the water level float that is on the left side of dishwasher is stuck.\015\012\015\012Either remove side panel and flick lever or pull dishwasher out and tap lower portion ... Bosch SHY56A02 / SHY56A06 Built-in Dishwasher

Champion dishwasher we have a champion freestanding dishwasher at my church. after the cycle is completed, the pressure guage behind the washer still shows 25-30 and it contnues to spray water. not forced by the motor, but more like a stuck open fill valve. if i turn off the water and run it, then turn the water back on, the valve is closed and does not let water freely in. butif i run it with the water on, it will continue to spray in freely after the cycle light goes out and you open the door.


If you turn the unit off from the circuit breaker will the water still run?if so the guts inside the solenoid valve are worn.you can call champion and get a kit to replace the worn parts and its not difficult to do.hope this helps. ... Dishwashers

Glasses have a film after washing complete. No food particles, just heavy film. I suspect dishes are the same, but doesn't show as much. Water temperature entering washer is 130 degrees. Heating element heats during drying cycle---not sure during wash cycle. Sounds like a good water spray during washing cycle.


There are many probable causes of failure .A dishwasher's water inlet valve is its most common part to fail. When \015\012your dishes are not being fully cleaned, quite often a faulty ... Frigidaire 24 in. FDB421RF Built-in Dishwasher

Yes I have a whirlpool DU1345XTVB1 dishwasher. Just got in July. After each wash cycle the dishes are not dry. I have been using Finish gelpacs w/jetdry & also have a off brand drying agent in reservior to help dry dishes. The water temperature is set pretty hot & washer is draining good. I have tried checking wash cycle a few minutes into 1st cycle to see if water is in filling & heating. Didn't know if maybe heating element going out or thermostat not working? Thank you for your time.


<span style="FONT-FAMILY: 'Trebuchet MS'; FONT-SIZE: 10pt; mso-ansi-language: EN" lang="EN">Hi,<br />Check your heating element.. </span><br />\015\012<span style="FONT-FAMILY: 'Trebuchet MS'; FONT-SIZE: 10pt; mso-ansi-lang ... Whirlpool 24 in. DU1050SS Built-in Dishwasher

Fagor lf-017s Hi, my fagor dish washer is showing an f3 alarm. f3 shows as a flood or not draining alarm in my booklet. However there is no remaining water inside the dishwasher. I have removed the dishwasher and checked the pump which is fine. The pump is running at the start of each cycle until thr f3 alarm steps in. Any ideas why the machine is still asking to drain when there is no water inside?


The water level float is stuck in the "UP" position ... Fagor Dishwashers

Just had new Frigidaire dishwasher installed. When cycle is started, display shows 99. Unit will fill with water, run cycle for about five minutes, stop and empty water then display a flashing PF. Can not seem to find a list of codes for this.


Pf is means power failure. ... Frigidaire 24 in. PLD3465REC Stainless Steel Built-in Dishwasher

My kitchenaid dishwasher won't wash. The clean light blinks and if I can get it to cycle, it turns on to ''2 minutes'', during which 2 minutes it makes some washer-like sounds but doesn't clean, dry or spit out any water. Before this, I wash having trouble getting my dishes clean. I wash able to get the bottom rack clean using the heavy duty cycle, but the top rack still didn't clean


... KitchenAid Dishwashers

Fills with water, sounds like it starts to pump water then stops, then start again. It attempts to start pumping water 3 or 4 times them turns off leaving the water in the tub. I have read about the water needing to heat up for the cycle to advance. When I check the water that is left in the tub it is warm but not hot. The heating element is not hot either. I did a continuity test on the heating element and it seems to check out ok. I also did a continuity test on the red wire from the heating e


You have a wash pump problem. can be 1 of 3 things. most likely something is caught in the pump impelor if not the wash pump motor may be faulty or ceized or it could be the capacitor for the wash pump motor is faulty. you can try removing the wash p ... Maytag MDB7100AWB Dishwasher

I have an asko D3450 dishwasher. Washer makes buzzing/humming noise at start of cycle and then randomly through cycle. I checked the sump and pump appears to be clean and impeller spins freely. The cycle seems to work ok. Water is pumping out ok. If you open the door to stop the cycle, the buzzing will continue for a few minutes then stop. If the cycle is restart, the buzzing starts again. The vibrations seem to originate from under the lower spin arm.


If the sound is a bussing - it is the capacitor mounted to the pump. It is failing.Shown here (big white cylinder on right of pic).. ... Asko 24 in. D3450 Dishwasher

I have a kitchenaid dishwasher model kuds24se with a problem. I MUST hit cancel before I hit start. Note that it doesn't matter how long it's been since the last cycle. It could be a few minutes or a day or more. I have to hit start to get a complete wash cycle. If I don't hit cancel, the washer goes through some sort of cycle and stops. It seems like a normal cycle but of course it is not because I don't hear any water and, upon completion, when I open the door there is heat but the soap dispen


... KitchenAid KUDS24SE Built-in Dishwasher

I have whirlpool Dish washer model GU 120 ES (bought in 2001). When we start the dish washer cycle the unit starts for a minute, then the "start indicator" light flashes. As indicated in the instructions, we press the "start button" for five (5) seconds, at this time the washer clears the water out and stops. If you can assist this would be greatly appreciated. Thanks Jeff


I called the service tech.... ... Whirlpool Dishwashers

Hello, I have a problem with our Miele G646SC Plus dishwasher. It starts its cycle OK, draining out any residual water, taking in fresh water and doing the initial rinse. After about 5 minutes it then stops with the "inlet/drain" red light flashing. The detergent is still in the holder and the water is still cold. The filter at the bottom of the compartment is clean, the drain pump spins freely. I've also checked for any leaks in the bottom of the machine that would trip the styrofoam/microsw


Hi\015\012\015\012 \015\012\015\012The light flashing means an issue while draining. You would need to check for air\015\012gap on the dishwasher, it may be clogged. It prevents dishwasher\015\012from drain ... Miele 24 in. G646SC Plus Free-Standing Dishwasher

Fisher & Paykel DD24DCX6 Double Drawer DW shuts off at approx 2 minutes into cycle and again at about 24 minutes showing a water spigot symbol on the LCD screen


... Dishwashers

I have an Ariston LI45. The stupid thin one. It's not seen much work & is just out of Guarantee. It's stopped working & is showing 2 flashing lights. Stops partway in to a cycle with water in the base, but not enough to cover the element. Tried re-setting, no difference. I have also noticed that it's melted a plastic wheel off the bottom tray at the back. After reading problems with other washers, i'm guessing the water level switch & maybe element too. If this is the case, i'm ok finding the


... Dishwashers

I have a KitchenAid KDS-17E dishwasher, which has worked well since I acquired it second-hand in 1984. Last night it ran continuously, stuck in the prewash part of fullcycle, with water being pumped through the system, and was fairly warm in the morning. It drained normally when I pressed the Cancel/drain button. I tried the machine again in full cycle. After 20 minutes it was still stuck in prewash, with the water temperature about 42 C, so I stopped it. Machine is connected to cold wate


Your problem is a bad timer.and you really got your moneys worth on this dishwasher.The timers useally go much soon than this one 7-8 years is the norm.The timer gets stuck in one position is a good sign its loseing its ability to fuction normally, ... Dishwashers

I have a Miele Turbothermic dishwasher which is nearly 3 years old. The Inlet/Drain (red) light is flickering and the washing cycle was not completed. I cleared the strainer but have not been able to clear the the dirty, stagnant water. I tried re-starting it with everything out of the washer but nothing has changed. Is there a way to clear the water and get this machine working again? Many thanks. Loretta


Please provide the full model number of the Miele dishwasher.\015\012\015\012Have you checked that there is no blockage in the kitchen drain especially if you use insinkerator (disposer unit) in the sink. ... Miele Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1961 seconds