Having problems with your Miele Dishwashers ?

Our Miele G984SC does not start and the drain/intake light has been on since we cannot start it


Answers :

Is machine full of water? If yes, you probably have a drain problem. Check drain pump impellor is turning freely (instructions for this available from Miele website-go to Customer Support link, and download user guide for your model-it contains instructions for removing filers and accessing drain pump). If this is OK, check for kinks in drain hose, and check for blockage where drainhose connects to spigot on waste pipe (usually under your sink).\015\012If machine is draining OK and light still flashing, you may have problem with inlet valve/hose assembly-recommend calling service agent to repair.
Use powdered dishwasher detergent rather than liquid. It solved my problem immediately!
Repair Help & Product Troubleshooting for Miele Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Our Miele G984SC does not start and the drain/intake light has been on since we cannot start it


Is machine full of water? If yes, you probably have a drain problem. Check drain pump impellor is turning freely (instructions for this available from Miele website-go to Customer Support link, and download user guide for your model-it contains instr ... Miele Dishwashers

We have Frigidaire model # FGHD2433KB1. The problem is that we cannot select a mode to get it to start. We unplugged it and the light for China Wash lights up, but it will not start. The number 92 appears in the window on front appears for about 5-seconds and disappears for about 30-seconds and does it all over again. We cannot get it to start.


... Dishwashers

I HAVE A BAUMATIC D/WASHER BHD5 TYPE DW-24E1,(ABOUT 8 YEARS OLD) IT IS A WHILE SINCE LAST USED THEN 1 NIGHT AS IF IT HAD STARTED BY IT'SELF IT STARTED MAKING A BEEPING NOISE ALL 4 INDICATING LIGHTS AS WELL AS SALT AND RINSE AID WERE FLASHING HAVE SINCE TOPPED UP SALT AND RINSE AID BUT ROUGHLY 1 MINUTE AFTER STARTING IT BEGINS TO BEEP AND ALL LIGHTS FLASH. COULD YOU TELL ME THE PROBLEM. MANY THANKS


... Baumatic Dishwashers

Whirlpool ADG 957. Light for rinse programme on but start light flashing intermittently. Cannot change programme, cannot start machine.


Mine was doing exactly the same. I turned off power, held down the 2 black buttons on right, switched back on and the start button flashes intermittently. It then allowed me to change programs, just testing it now!! It started, this was more then ... Dishwashers

KUDU03STSS2 The dishwasher won't start and you cannot select a cycle. Hiting cancel twice will turn a small steady light on in the time window were the spining light normally is before a cycle starts, at which time closing the door will drain the dishwasher. Tried using the reset combos: hot wash, heat dry, hot wash, heat dry - all lights came on but nothing reset. Also tried same sequence doubling the heat dry. Unpluged for ten minutes, still nothing. Can select rinse, but unit does not start,


... KitchenAid Dishwashers

Kenmore elite model 665.1669 or the 1769 model. All lights are working except for the start button light. When i hit the start button nothing happens. No blinking light, it's like it is dead. Cannot start the washer.


It appears your timer/main controller/CCU has failed in this instance.For replacement parts - head on over to PartSelect.com or RepairClinic.com and enter in your full model number for a full parts listing.I recommend both sites bec ... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

Built in model MDB5601AWB- about 3 years old. The touch panel stopped working..no lights would come on when touched. Tried it a couple of days later. Lights came on..finished a cycle. after satying in the wash mode for a few hours. Then lights started flashing on and off. At that point I shut it off at fuse box since I couldn't get lights to stop blinking and haven't trusted to use since


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. From what you have described it seems to be the ... Maytag Dishwashers

I have a Kenmore Elite Dishwasher Model 665.172824000. We think it stopped part way throught the dry cycle. The green "Clean" light has been flashing since in 7 flash cycles non stop. I tried pushing the Cancel button, it starts the drain pump then stops and we are back to where we started. I tried to start a new wash cycle but when I close the door and push the start button it just give 3 quick red flashes and then nothing but the green clean light flashing again. I shut the breaker off fo


So sorry but the partsdirect site for sears locked down my computer. Check where the drain hose connects to your pump and see if there is a small device the hose connects to that has 2 wires going to it. If it does unplug the wires, turn power off, w ... Dishwashers

When starting my Bauknecht GSFP 5586 dishwasher the program is set for rinsing and the start light flashes two blinks, then again two blink etc. I cannot get the program to change. When I hold the Start button for 2 seconds, the progress light flashes at END for a moment then reverts back to the double blink sequence. I have checked the filter and it is well seated and clean. What can I do to start the program selection again?


Ok, so I had the exact same problem with the exact same model. NOT 7 blinks and to buttons that you do not have.\012I will tell you what I did as I do not know what (if any) of what I did fixed it (it could be luck but I do not think so).\012 ... Dishwashers

Dishwasher Fault Hi, My dishwasher is a Diplomat ADP8322 (which i think is a rebadged whirlpool unit) & has been playing up recently. When you start a cycle it is fine for a minute or so then it starts beeping, the rinse light comes on & the light next to the start button flashes 11 times, pauses then repeats. I have read online that this flashing relates to what the fault is, but i cannot find out what fault the 11 flashes relate to. The first time this happened i cleaned out all of the filters


... Dishwashers

The touchpad buttons no longer work to select a wash cycle. When I push "Start" the light above "Smart Wash" comes on and the dishwasher operates normally, but I cannot select any other cycles and the light only comes on after pressing "Start", not before. Also, the Options buttons seem to work normally but the delay button doesn't scroll through 2-4-6, it only toggles the light on and off above "4". The item is 15 months old. Thank you.


... Kenmore 13743 Staimless Steel Built-in Dishwasher

Hotpoint BC145 Dishwasher not cleaning starts to kick in but then just sticks on the "R" light flashing and cannot reset even after turning off. Itbeeps when pressing the select button sound weaker and shorter than they used to and the light does not move from the "R". On a couple of times I have tried it has reset and then the dishwasher starts but after about 3 minutes there is a low beep(not the usual beep when a programme finishes) and the washer stops and the light is flashing on the "R" ag


... Hotpoint 18 in. BCI45 Slim-Line Built-in Dishwasher

Cannot select any wash cycle but quick wash. No other wash cycles will light up when selected. If you select the start button, the quick wash lights and the dishwasher starts (even with door open).


I had this same problem and being an electrical engineer, I decided to see what I could fix before replacing the board. The symptoms were the only cycle I could run was the QUICK WASH - no other cycle buttons responded.\015\012\015\012I took t ... Jenn-Air 24 in. JDB1080AWS Built-in Dishwasher

She6af02uc bosch dishwasher Light is flashing, but won't start. I used it earlier today and it worked fine. Like I said the time light is flashing, but I cannot change settings nor will it start. Turned it on and off a few times to no avail. Did I lock it or something? How does one unlock it? Hardly used and only a couple of months old... Never had this problem before!


... Bosch Dishwashers

Green light flashing and water still in bottom of dishwasher. I have cleaned the filters also I cannot reset the start button it just keeps starting again and then stops and green light flashes again


Hi,If this is the clean light the follow the link below, it will explain the flashing and how to reset the control so you can use the dishwasher again. ... Whirlpool Dishwashers

My Maytag will not start. I have just replaced the PCB , the lights on the panel came on until I pressed the start button. The lights went out and I cannot get them back on.


I am sorry, but is it please possible for you to post the Model no. of your Maytag dishwasher. I am not able to see it in the chain of comments you have had with another Fixya.com consultant.\015\012\015\012Have you considered the possil ... Maytag Dishwashers

She6af02uc bosch dishwasher Light is flashing but won't start. I used it earlier today and it worked fine. Like I said the time light is flashing but I cannot change settings nor will it start. Turned it on and off a few times to no avail. Did I lock it or something? How does one unlock it? Hardly used and only a couple of months old... Never had this problem before!


... Dishwashers

I have a F&P dishwasher model DW60CDX1 (around 5 years old) which we cannot start a cycle. The dishwasher turns on (power button and all programme indicators light up) but when you press a programme button nothing happens - the lights don't change. We have switched the power off at the powerpoint and on again a few times but this has not rectified the problem. It was playing up before this in that sometimes the programme would not start when a button was pressed but I just closed the door mor


The micro switch in the door which senses the door closing has probably failled. This is accessible once the inner door cover is removed. Switch should be under $10 from electrical store. Or buy through appliance manufacturer. ... Fisher and Paykel Dishwashers

I have an integrated program 2000 dishwasher which has started to beep since I moved it. The cycle starts but after a couple of minutes it stops and starts beeping and the green light above the start button keeps flashing in sets of 4. I have searched everywhere for a manual but haven't had any luck so far.


... Dishwashers

Hello. I have a Kitchen Aide KUDG255HWH1 that will not start from a cold state. The "Energy Saver Dry" and "Normal" indicator light/ switches failed to operate about 1 month ago and since then I have needed to use the "High Temp Wash" and Soak & Scrub" cycles to get the unit to run. Now these two indicator kight will illuninate but the unit will not start when I depress the "On" soft switch. When I depress the cancel switch the unit starts with what sounds like a pre-start cycle. Pleas


Hi\015\012\015\012\015\012\015\012\015\012\015\012Thanks for using FixYa. To reset the dishwasher switch\015\012off the dishwasher from the power socket and mains for five minutes and then\015\012switch it back on. If still the issu ... KitchenAid Dishwashers

Fdw60 dishwasher yet again my dishwasher has broken again, now it is trippin my electric in the house, the problem that was starting up was a eco light flashing i read on here what to do and that seemed to of fixed it, but since i did that it starts up and as soon as water starts to enter it trips my electric and advice would be great


Hold the start key down and it should re-set . Please Rate This ! Thanx!! ... Hotpoint 24 in. FDW60 Free-standing Dishwasher

I have a Maytag quiet series 200, it been working fine since I purchased it last year, as of today I pressed start and it won't start and yet when I press the delay buttons of 2, 4, 6 it lights up and so do the other functions but to change my settings that doesn't work neither as well as my start button. Whats wrong with it? Any ideas? My model # is NY2222514


... Maytag 24 in. MDBH940AWS Built-in Dishwasher

My 450 pro Viking dishwasher (only a couple of months in use!)has both lights of normal wash and light china on, as well as the power light on. I cannot cancel program or start. It goes nowhere. Can someone please help me? I have 5 young kids at home and this is my idea of a nightmare! HELP!!!! Thank you VERY much Alma


\015\012Ok so your dishwasher won't do anything... it justs sits there and "Hums" you can't make it respond to any controls, and the ONLY way to Stop it. is to unplug the unit, replugging back in it simply "Hums" again and will do nothing. ... Viking Dishwashers

Smeg DF612S All starts well but after 40 minutes stops with a beep and will not progress to the main wash cycle. Instead all programme lights come on (located on the left), along with the first 2 phase lights (the first two of the lights on the right hand panel). This indicates error code 3 (cannot pump out water), but water is entering and draining perfectly. Please advise.


Check to make sure there r no kinks’ in the drain line or\015\012that it is not clogged it sounds like the sensor is tripping because there is\015\012too much strain on the pump just like a breaker. ... Smeg 24 in. DWI612 Built-in Dishwasher

Control panel cancel light blinking as well as normal and light china light cannot cancel or start dishwasher


Where do i connect the upper rack water conduit tube for the kitchenaid dishwasher ... KitchenAid Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0842 seconds