Having problems with your Miele Dishwashers ?

Lights flashing at end of cycle, dishes not clean

\015 The lights are flashing at the end of the cycle, dishes not clean. The wash cycle seems fine but at the end the dishes are not clean or dry and both the green Start button and the yellow End button flash. I have turned it off and re-entered the settings but it has not worked.\015

Answers :

I switched it off at the wall and left it for a minute and set the dial to Stop and then set it again from the beginning and so far it has been fine. Thanks, DCD
Repair Help & Product Troubleshooting for Miele Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My G832SC is not draining at the end of the cycle. It runs the entire cycle, and the dishes appear to be clean. The soap dispenser has opened and the dishes are rinsed. However, the dry cycle doesn't run because the machine doesn't drain at the end. The intake/drain light is flashing. If I reset the machine and start a new cycle, it will perform an initial drain and the water level does go down. We checked the tri-filter and the valve pump thing, rinsed both. Checked the hose under the sink. We


... Miele Slimline G832SCi Built-in Dishwasher

Lights flashing at end of cycle, dishes not clean


I switched it off at the wall and left it for a minute and set the dial to Stop and then set it again from the beginning and so far it has been fine. Thanks, DCD ... Miele Dishwashers

I have a Kenmore Elite dishwasher (model 665.1315), and the dishwasher will run through the wash cycle as expected, but when it gets to the heated dry cycle , it doesn't appear to dry. It will then flash a fault code 81 (8 short flashes of the 'clean' light, pause, and then 1 more short flash of the 'clean' light, longer pause, and repeat the code). The dishes seem to be somewhat dry, but there is certainly water on the dishes and on the tub (there is never any water standing in the tub, and t


Hi,Check your heating element.. \012A bad heating element causes many problems in dishwashers...Dishwasher Problems The ... Kenmore 24 in. 15932 Built-in Dishwasher

My baumatic dishwasher bad6005 appears to do a full cycle but ends with 2 lights flashing the third and fourth light. The dishes are kind of clean? Thanks


... Dishwashers

When we run our dishwasher at the end of the cycle it does not finish. The clean light flashes seven times then repeats. Some of the dishes and glasses come out feeling slimy. We were told it was a drying element. But the element did get hot. What's up with it?


Hi\015\012\015\012\015\012\015\012\015\012\015\012Thanks for using FixYa. If the\015\012clean light flashes 7 times, pauses, and then repeats. When the dishwasher\015\012doesn't sense a water temperature increase, it stops working a ... KitchenAid 24 in. KUDS01DLSS Built-in Dishwasher

I have a Maytag MDB8951bws and I have noticed that the dishes at the end of the cycle do not feel hot but mildly warm and not completely dry. I also noticed that when I select the ''Sanitize'' option the light that tells you the dishes have completed being sanitized does not come on after the cycles are completely finished (the ''clean'' light does come on). One last note I will throw in is that the high temp wash seems to work quite well as a lot of steam is expelled when the door is opened dur


... Maytag MDB8951BW Dishwasher

I have the Whirlpool Quiet Partner 1 the wash cycle starts and about 20 Min.'s into it the clean light starts flashing or the the start light, one or the other each time and it wont dry the dish's anymore we have already replaced the panel once and it has always popped when it is filling with water or changing cycles. HELP!!!! I hate washing dish's and I am beginning to hate all Whirlpool Appliances.


If the clean light blinks 7 times thats you heating circuit. Test the heater with an ohm meeting to see if it has open. If so order the heater kit and it comes with the control board. ... Whirlpool GU2400XTP Built-in Dishwasher

I have a Triton dishwasher. Last cycle, it completed washing then started drying and started beeping and the drying light is flashing. When I finally opened the latch, the beeping stopped, but the drying light is still flashing. The dishes were clean and warm - they air dried the rest of the way. I have not been able to get the drying light to go off. I have turned the breaker off over night, and flipped back on. The dishwasher goes back to flashing washing, and then clicks to drying and th


Hi,\015\012Make sure the salt level is ok - add 1Kg of salt if you have not done it in a while, and check rinse-aid level if apliccable.\015\012\015\012If this does nothing, then remove the lower kick panel for access to a data shee ... GE Dishwashers

My SHE4402UC/36 dishwasher malfunctioned all the lights were flashing and the machine was trying to drain. The guy came out and replace the control board. The dishwasher now read 199 on all cycles except the rinse and hold, the santitized light does not come when its done. The repair guy told me the count down timers were flakey on the the Bosch dishwashers and it would learn my dishwashing patterns in time. So 6 cycles later the dishes are still damp at the end of the cycle-the length of the cy


Well its not baloney but it is cheesey. normally changing the module is the cure but it has to be programmed correctly. bosch has a recall so check it out and see because the recall is free and the tech is suppose to know how to program it. go to the ... Bosch 24 in. SHE44C02UC / SHE44C06UC / SHE44C07UC Built-in Dishwasher

Regarding Maytag Dishwasher, model # mdb4651aww3. Most of the lights on the control panel will not light up. You can't change cycles or set the delay timer etc. You can hit the start button and it runs a perfect cycle, and ends up with clean dishes. You just have no idea what cycle it runs.


I have same problem with my Maytag. Had a repair guy come out and he said it's the 'controller card', not the button touchpanel. The controller card is $127 and not in stock and there's a 'several month wait'. I'm not going to wait, going to buy ... Maytag 24 in. MDB4651A Built-in Dishwasher

Help! My Whirlpool Quiet Partner II isn't working at all. Water was standing in bottom at end of last 2 cycles, but on the last cycle, I came home to clean looking dishes, standing water, and a machine that won't turn on at all- no lights on any buttons- nothing works. I've tried the reset codes published here and elsewhere, but there are no lights on any buttons at all. The circuit breaker is fine. I have 3 young kids and can't function long without my dishwasher!


There is a fuse in the control panel what your model# i can get you the part number its easy to replace it. ... Dishwashers

Whirlpool Dishwasher ADP 2652 WH at the end of a clean cycle, the pre rinse button remanins on, the "end" light flashes constantly and the on/off button flashes 4 times in a repeating manner.


... Whirlpool Dishwashers

Kitchenaid kudc03fvss0 dishwasher stopped mid cycle without drying dishes last week and then stopped altogether with lights flashing and full basin. I disassembled filter/pump cover in bottom and cleared several plastic pieces and cleaned chopping blade and screen. After unplugging/plugging and pressing cancel button the pump runs for about 10 seconds and stops with normal and heavy duty lights flashing. What should I check next?


... Dishwashers

Dishwasher is not drying. At end of cycle, dishes are still wet and damp, as well as the inside. Buttons are all pushed. Also, it seems to wash for more than one cycle. Did a light wash and after 1-1/2 hrs., it was still running. Purchased a couple of months ago. Dishes don't seem to be as clean as my old dishwasher.


Hi,Check your heating element.. A bad heating element causes many problems in dishwashers…Dishwasher Problems The ... Whirlpool MDBH969AWB Builtin Dishwasher

Cleaning light the clean light will not stop flashing and i can not select a cycle to wash the dishes


Hi,This is flashing due to a fault with the water heating. Here is a link to instructions on how to reset the control so you can use the dishwasher and what may have caused the failure. Let me know if it was helpful. ... Whirlpool GU2400XTP Built-in Dishwasher

I have kenmore quietguard 3; model 665-17022401. The clean light flashes at the end of every wash. The codes work to reset the light, but it reappears after every wash and the dishes are not clean. Any thoughts?


... Dishwashers

Our Whirlpool KUDP01ILBS2 dishwasher isn't working like it used to. Dishes seem to be getting partially clean, they aren't getting dry at all and it seems they may be being rinsed/washed with dirty water. There is plenty of water in the machine when I interupt the cleaning cycle. I always run the hot water in the sink before I start the dishwasher so the first water into the dishwasher is as hot as possible. Also the sani-rinse light is flashing when the cycle "completes".


Heat that is retained in the dishes is largely responsible for drying\015\012in this dishwasher. Since plastics do not retain heat very well, they\015\012will not dry as well as glasses, ceramics or metal dishes. Rinse aid\015\012must be used so that ... Dishwashers

Candy CDI1012 Integrated dishwasher. When I turn on the dishwasher and start it - for some reason it can not go the whole way through the cycle. When I open the door the - programme light is flashing and water is still in the bottom of the dishwasher - ie mid cycle. The water will only drain if I put it into another program to drain away - but as the dishwasher was mid cycle - the dishes are not clean


Hello mm1973,It could be because of bad door latch switches / blown thermal fuse / blown or oversensitive control board. In all these scenarios, a dismantling of the machine is required. If you have no prior experience, I'd recommend get ... Dishwashers

I have a Kenmore Elite Dishwasher Model 665.172824000. We think it stopped part way throught the dry cycle. The green "Clean" light has been flashing since in 7 flash cycles non stop. I tried pushing the Cancel button, it starts the drain pump then stops and we are back to where we started. I tried to start a new wash cycle but when I close the door and push the start button it just give 3 quick red flashes and then nothing but the green clean light flashing again. I shut the breaker off fo


So sorry but the partsdirect site for sears locked down my computer. Check where the drain hose connects to your pump and see if there is a small device the hose connects to that has 2 wires going to it. If it does unplug the wires, turn power off, w ... Dishwashers

Power light together with 'Intensive', 'Normal' and 'Soak' lights all flash in unison towards end of wash cycle with a gurgling sound from the pump suction that doesn't stop until the power is switched off. Water inlet filters all cleaned with no affect.


... Hotpoint Dishwashers

I have an Ariston LS245 dishwasher, have just had the pump replaced, as it had shorted out, due to water in the bottom tray where the water detection float is, also a new drain hose fitted. Have just run a wash and after running a while, presumably to the end of the rinse, wash and dry cycle, then one of the cycle phase lights, the one for 'soak' blinks constantly. I switched the machine off and had a look to see if a wash had been done, the dishes look clean. In the book it says that if one


... Ariston Technologies Dishwashers

The dishes especially the silverware is not getting clean. After a cycle is finished the clean light is flashing.


... Whirlpool 24 in. DU1100XTP Built-in Dishwasher

Drain/ Inlet red light flash in the the middle of washing cycle and then dish waher stopped. Drain cleaned a few time. It works a cycle and does do the same next time


Check float /i.e drain hose/ must be in as built positions ... Miele Dishwashers

Hi, I have a Miele dishwasher G2150 that after 7-10 minutes on any cycle the rinse, dry, and end lights flash amber. I called the 800 number and they walked me through the diagnostic sequence and they said it was an error code 12 something to do with water restriction. I removed and checked the bottom "L" filter(clean), the wheel (moves freely, not dirty), and the grey in line filter screen on the intake hose,( clean also). I can feel the water coming through the intake hose, water comes in thro


... Miele G2150SC Dishwasher

Dishwasher says dishes are clean but is still stuck in cycle. tried resetting the breaker but no luck. the green light that goes on when clean is constantly flashing but dishwasher is non-responsive. any feedback would be appreciated! Thanks


Some dishwashers have some sort of float switch. They can stick , try rocking dish washer if stuck mid cycle, I would make sure the food collect grid at bottom is clear, try flushing machine through with an empty load now and then, you can buy stuff ... Kenmore Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1222 seconds