Having problems with your Miele Dishwashers ?

When attempting to start dishwasher load the signal F 70 come up and it wont work. Purchased 2nd Jan 2008.


Answers :

F70, waterproof system activated. this means you have water in the bottom pan of the dishwasher. your miele shuts itself off and runs the drain pump continuously any time water leaking is detected. you can pull out the black plastic toe kick under the door. there is a cover panel in the center held on with two t20 screws. you can dry up the water and try to run a cycle. if it works ok, cut back on your detergent by 1/2. if it leaks again, you should probably request service from miele. if you want to try to repair it yourself, let me know and I will help you troubleshoot it further.
Repair Help & Product Troubleshooting for Miele Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

When attempting to start dishwasher load the signal F 70 come up and it wont work. Purchased 2nd Jan 2008.


F70, waterproof system activated. this means you have water in the bottom pan of the dishwasher. your miele shuts itself off and runs the drain pump continuously any time water leaking is detected. you can pull out the black plastic toe kick un ... Miele Dishwashers

Kenmore undercounter dishwasher model 66517019400 wont start..I want to purchase a new control board do you think this is the problem? normal cycle light comes on, cancel button works, heat on button works, just wont start ??


It might not start because the water solenoid is failed, or the water level sensor is failed.\015\012\015\012You have to use a meter to test these components first. Put your voltmeter on the two leads going to the water solenoid, and psuh ... Kenmore Dishwashers

My Bosch dishwasher had been working though there was water coming up from sink overflow valve starting yesterday. Today after two loads the dishwasher woul not start though the door clisks shut and the indiactor lights are on. Any ideas?


Based on the symptoms, ie, dishwasher not being able to drain, it is likely there is a blockage somewhere in the system.\015\012\015\012If you can remove the drain outlet of the dishwasher from the sink and try to run the dishwasher into ... Bosch 24 in. SHX33A02 / SHX33A06 Free-standing Dishwasher

I have a zanussi tempoline dishwasher, I have loaded this as I usually do, turn the knob to the right and select the 2nd programme the light next to this comes on, I have pressed this to start the machine although it seems as if it is going to start this light flashes and the top arrow on the right of this flashes intermitanly, but the machine does not start the wash programme. The 3hr delay button if I had pressed this by mistake which I am sure I have not would light up. When I found it did no


Hi Ruth.The machine can be in error mode. In this case one or more lights in the control pad will stay on or flash and the cycle will not start.One of the most common fault in your situation, and at start of the cycle is no wa ... Zanussi Dishwashers

I purchased a second hand Electrolux Dishlex DX403 with a kitchen. The dishwasher turns on when I turn the powerpoint on and makes a noise as if it is about to start. I attempt to press the buttons to set a mode and start it and it wont work, the buttons dont do anything. How can I fix this?


... Electrolux 24 in. EDW5505EPS Stainless Steel Built-in Dishwasher

Frigidaire Dishwasher Lights wont come on, hit start button, makes noise, no water then eventually shuts off. Couple weeks ago, had work done to furnace now not much water pressure in house...


Find your main stop cock in your household for cold water supply and make sure it is fully open(anti clockwise).If this makes a difference to rest of house, then your washers pressure should be fine too.If still same problem, check your washers fill ... Frigidaire 24 in. PLD2850 Built-in Dishwasher

The dishwasher ligh blinks showing that its clean. when i go to load it and start it it wont reset, it blinks as if its clean. how do i reset it. ive turned the breaker off and nothing works.


... GE 24 in. GLD5500L Built-in Dishwasher

Green clean light wont stop blinking unable to use dishwasher . It is an energy saver. the drain button works ..and when you push start the light comes on but will not run for cleaning


HiThanks for using FixYa. If the clean light flashes, pauses, and then repeats. When the dishwasher doesn't sense a water temperature increase, it stops working and locks the functions (clean light fla ... Kenmore 16602 / 16604 / 16609 Built-in Dishwasher

I bought a new lg ldf6810bb/01 when re-doing the kitchen. After about a year, the dishes quit drying. Since we had bought an extended warranty, we have had several repairmen out to check on this. The did change the fan in the door, but now says everything is working as should. However, it still wont dry the dishes. We finally got in touch with the distric manager for best buy where we originally purchased, and after some more reps coming out, finally replaced the dishwasher. However, t


... LG LDF6810 Built-in Dishwasher

Frigidaire dishwasher does not start. but i see the cycle select LED light come on . all of a sudden the dishwasher stopped working. all buttons except the "start" work. i can select 'normal', 'pots n pans', select the delay etc, but the START button will simply not work!


... Frigidaire 24 in. FDBB945DC Stainless Steel Built-in Dishwasher

My Delonghi Dishwasher keeps turning off. The dishwasher is turned on at the power point. The water is turned on. Okay When I press the POWER botton on the front it wont stay on. I have to keep my finger on the POWER button and then press the START button for washer to work. If I do this it will then pump out any water in the bottom and start to work. ***BUT when you take your finger of the POWER button the washer just turns off and stops working. Do you have any idea what could be the problem p


Yes, the power button is faulty. by pressing the power button forcefully, you are in effect allowing the contacts to close. Replace it. ... Dishwashers

I have a 4 year old Maytag MDBH945AWW and the panel lights come on and I can select cycles... but the dishwasher wont start. I tried holding the start cancel button, tried turning the breaker off for a couple of hours, took the inner panel off the door and checked the latch, but its still wont start. Any other suggestions? If it needs a new control panel its probably better to just get a new similar dishwasher for $300, correct?


What you need to do is read for continuity and power across the door latch switch. (2 white wires) AND 2 Black wires Both wires must read continuty at the control panel connectors to the power source terminals for the unit to start. Since the co ... Maytag MDBH945AWW / MDBH945AWQ / MDBH945AWB Built-in Dishwasher

I have a General Electric pdw7880J03ss dishwasher. Tonight, I went to start a load of dishes and the Heated Dry option wouldn't turn off without the lights going to RINSE ONLY. Then the 1hr setting started coming on. Then was able to get the load to start but then it stopped somewhere in the cycle. Now, no lights will come on the panel though I can hear the beeping. Dishes appear to have washed...


Hi\015\012\015\012Press and hold the heated dry button for 15 seconds to reset\015\012the control, if this wont work then it means that the control board is bad and\015\012should be replaced. Hope this helps...please post back for further ... Dishwashers

Our AEG Favorit 50620 dishwasher won't start. When I push the power button, the power light comes on, but none of the other lights. Pushing the function buttons has no effect. The door is fully closed, and it was working perfectly before. I have tried turning it off and on, unplugging it etc. Nothing works. Interestingly, if you push more than one function button at the same time, some of the function lights come on, but then when you try to start the cycle it still won't work. Help!


... AEG 24 in. Favorit 40650 Free-Standing Dishwasher

KitchenAid KUDI10FL dishwasher- The door spring system broke and I repaired it, but now all of the sudden the dishwasher will not start. The door may have been dropped a couple of time before the spring system was repaired, but it did not hit the floor, just a hard sudden stop. All of the cycle setting lights come on when they are pressed except for the start button. Just before the start button stopped working the dishwasher started by itself or started several hours after cycle selection had b


Hi- It is possible that the door latch is not completely engaging. If the door dropped the hinges may have bent a little thus preventing a good contact with door switch. Try pressing and holding the door shut, hard, and pressing start. If that wor ... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

Whirlpool dishwasher The dishwasher works off and on. Every few days it stops going on altogether...only the cancel button goes on and the the dishwasher's timer says 2 minutes. Sometimes the air dry button works,but none of the other buttons work. The problem has been when the repair person comes out, it all of a sudden starts to work and so he can't diagnose the problem. I spoke with someone who said it sounds like with the touch pad or computer control board is bad. You don't seem to list my


Hi there,\015\012\015\012your problem is intermittent and before you start replacing parts, i would recommend that you do these checks:\015\012\015\012unplug the dishwasher from the wall\015\012check the connection betwe ... Dishwashers

Whirlpool dishwasher The dishwasher works off and on. Every few days it stops going on altogether...only the cancel button goes on and the the dishwasher's timer says 2 minutes. Sometimes the air dry button works,but none of the other buttons work. The problem has been when the repair person comes out, it all of a sudden starts to work and so he can't diagnose the problem. I spoke with someone who said it sounds like with the touch pad or computer control board is bad. You don't seem to list my


THE TECH WHO CAME TO FIX MY DISHWASHER FROM Y=THIS EXACT PROBLEM TOLD ME THAT IT IS CAUSED BY THE WATER THAT TAKES TOO MUCH TIME TO GET WARM, SO YOU HAVE TO MAKE SURE THE WATER IS NOT GOING TO BE COLD BEFORE YOU TURN THE DISHWASHER ON. AS TO FIXING I ... Whirlpool 24 in. DU1100XTP Built-in Dishwasher

My Bosch Dishwasher model #SHU43C06UC/17 in 5 years old and has been working great and all of a sudden last week it stopped working. When you try to start a new load it will start the timer, but the dishwasher won't fill and run. Any Ideas on what to check or what may be the problem?


Hello,\015\012\015\012Welcome to FixYa.\015\012\015\012I would first run a diagnostic to see what error is presented and in turn will direct which way to focus the repair.\015\012\015\012Try this and t ... Bosch 24 in. SHU43 Built-in Dishwasher

I have an inglis ipu5846 built in dishwasher it fills thaen trys to start but wont start or drain now i took off the lower spray armthe part that is screw down under it tryed cancel drain and it worked put thetop bacck on but not the spray arm and it wont work.what stopping that from working there are not any moving parts on that piece


... Whirlpool Dishwashers

Cranky dishwasher I have to admit my wife's solution is the only one that works. Our ten-year-old Superba built-in usually starts a normal cycle part-way through, at the wash part, without filling or opening the dispenser door. Therefore the dishes come out with the soil now baked on. Closing the door, selecting normal and start results in a pump-out sound, or at least just the pump running to wash the dishes. The dishwasher ignores any cancel button push,and the light does not come on over t


You want to make sure that the dishwasher is level and secure first of all. Then I would look into the door latch assy. Sounds to me that you are not making all the latch switches when closing normally. When you are slamming it, you are making the s ... KitchenAid KUDS24SE Built-in Dishwasher

Neff dishwasher our dishwasher is six years old and have had no problems till now . there is power to it but when you push the on button the impeller starts up even when the door is open , and it wont go through the cycle , its asif there is no water going in and it is not draining away i have checked and cleaned the filters but nothing, then pulled it out from undre the sink and it started working . i put it back , it went through the cycle then the next day it would'nt work again . do i need a


You have a faulty door switch. It can be replaced and may be available at youre local appliance parts dealer. ... Dishwashers

The touchpad buttons no longer work to select a wash cycle. When I push "Start" the light above "Smart Wash" comes on and the dishwasher operates normally, but I cannot select any other cycles and the light only comes on after pressing "Start", not before. Also, the Options buttons seem to work normally but the delay button doesn't scroll through 2-4-6, it only toggles the light on and off above "4". The item is 15 months old. Thank you.


... Kenmore 13743 Staimless Steel Built-in Dishwasher

I have a bosch smu 2000 series dishwasher. it has always worked well with no problems but then all of a sudden a week or so ago, the water stopped coming into the dishwasher to wash the dishes. the faucet and all other water areas continue to work w/o problems (i.e. bathroom, shower etc). in attempting to use the dishwasher, the entire cycle seems to be working, i initially hear what sounds like an initial water discharge when the cycle first starts and during the entire cycle it sounds like it


... Bosch Dishwashers

The ge profile dishwasher model PDW8280J10SS was purchased about 2 yrs ago. It was working fine up until Jan. 2009. It ran fine but the water stopped draining. I read were you should run the garbage disposal prior to running the dishwasher. I drained the water and did this. It worked fine for a while then the problem was back. Once again, Drained all the water, sucked it out with a turkey baister, moved the dishwasher and checked hoses etc. Once again, it worked fine for about 10-14 runs. It now


It is probably clogged at the pump or before. See if you can get outlet hose off the bottom before the pump. ... GE 24 in. Profile PDW8280JSS Built-in Dishwasher

Dishwasher lights work but wont start


... Frigidaire Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2761 seconds