Having problems with your Miele Dishwashers ?

Miela G1220.My inlet/drain light is flashing and it says F 12.What do I need to do?


Answers :

Hello and welcome to fixya could you please describe the problem your having as well as provide make and model number
memwhistler says:
Miela G1220 dishwasher.the inlet/drain light is flashing and it is showing F12

rickead1 says:
ok one second while i go pull up that make

memwhistler says:
Miele G1220 SCU

rickead1 says:
f12 is water inlet restriction

rickead1 says:
says this exactly in your repair manual

rickead1 says:
Open the stopcock fully.
??? Clean the water inlet filter (see
"Problem solving").
??? The water pressure at the
intake is lower than 30 kPa
(0.3 bar).
Seek professional advice.

rickead1 says:
i think it better if i just send you the manual

rickead1 says:
www.miele.co.uk

rickead1 says:
page 41 says how to clean the inlet filter

memwhistler says:
Yes that would be good.

rickead1 says:
can you see your manual from that link

rickead1 says:
its a pdf

memwhistler says:
Do I need to clickon that link?

rickead1 says:
yes

rickead1 says:
in order to see it then save it to your favorites

memwhistler says:
I'm in Australia.

rickead1 says:
oh your close to me im in hawaii

rickead1 says:
lol

memwhistler says:
Oh i was just over ther in December...

rickead1 says:
nice i came here in may started working for government hoping to move back to mainland soon its nice to visit

memwhistler says:
Thanks,I got the manual and I will check it out!

rickead1 says:
kk do you have any further questions at this time

memwhistler says:
No thank you.Will check out the manual.thanks and bye.

rickead1 says:
please remember to rank by ending chat accepting solution and picking how helpful this was thanks again


Repair Help & Product Troubleshooting for Miele Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Miela G1220.My inlet/drain light is flashing and it says F 12.What do I need to do?


Hello and welcome to fixya could you please describe the problem your having as well as provide make and model number memwhistler says:Miela G1220 dishwasher.the inlet/drain light is flashing and it is showing F12 ... Miele Dishwashers

Heater circuit the clean light is flashing whirlpool csr says heater circuit malfunction you need a service call


Whirlpool dishwasher won't go into washing cycle ... Whirlpool Dishwashers

Whirlpool model DU960 - from 2001, I think. Stopped running mid-cycle and the cycle lights flash. Won't run. How to fix? If I press 'Cancel/Drain', it flashes that button light. If I press one of the wash cycles again, it turns on the pump for about 1 second, shuts off and the lights flash again. I tried turning off the circuit breaker and turning it back on, but it still won't run. Is this fixable? Do I need to call for service? Or, would I be better off just replacing it?


I have a whilpool du960 the rinse only light is flashing and the light wash light is also flashing. ... Whirlpool Dishwashers

My Dishlex global 300's rinse light is flashing after 5 mins use. About 2 inches of water stays at the bottom of the washer. Bought this second hand and it has not been used for a few months. Do I need to fill the reservoir under the washer or lean it at 45 degrees to dislodge anything in the sump. If you have had the problem of the washer starting its program and then stopping after 5 minutes and the rinse light flashing I would appreciate your advice. Cheers Hyph


The flashing rinse light is an error code. I am assuming that your control board is good because the lights are working. I'm also assuming that this model has two pumps. One for filling and one for draining. The rinse light flashing is probably i ... Dishwashers

Whirlpool dishwasher Clean light is flashing which says check heat circuit. I've reset board a couple times and run diagnostic. Element tests okay. Light keeps going back to flashing when running dishwasher.


... Whirlpool DU1055XTS Built-in Dishwasher

Whirlpool dishwasher Clean light is flashing, we just bought it last week and after the third wash, the Clean light started flashing and it won't go off, which stops it from doing anything else. User manul says to have it serviced, but that seems unneccessary. It doesn't seem to be draining completely, so there may be a knk in the pipe, which may be related, just not sure


The blinking clean light is an interruption in the dishwasher program that either indicates a malfunction, or a simple program glitch. The following link explains how you may be able to clear the blinking clean light problem: ... Dishwashers

Whirlpool dishwasher GU2500XTPS3 QUIET PARTNER. "clean" light flashing. Unit will not run. Light flashes seven (7) times. Manual says call service and check heater circuit.


... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

On the front of my dishwasher it says add salt add rinse aid check water. the red light comes on when i need to fill it up. Now the red light has come on saying check water... I don't no wht to do


This solution is for a Bosch, Siemens or Neff d/w. Please repost with Make and model if you d/w is none of the above.\015\012The tap signs or 'check water' means there is a problem with the water flow in or out of the machine. if you remo ... Dishwashers

My smeg dwi 710 dishwasher keeps flashing on the diplay panel and won't change to another wash selection. it wont close and wont start. the light is stuck on the heaviest wash selection and just keeps flashing on and off and on and off. i have tried turning it off, keeping buttons held down and nothing seems to work. there is nothing in the manual that says what the flashing means so i dont know how to fix it.


... Smeg Dishwashers

I have a fridgidaire dishwasher model # FDB 1450chc2 andon the control panel the red lights are flashing and washer wont start ?? when I open the door the lights go out but when I close the door and push start the washing lights start to blink but doesnt start to work ?? Need help thanks [email protected] Brian


... Frigidaire 24 in. PLD2850 Built-in Dishwasher

Quiet Partner II Whirlpool Dishwasher 2 years old, used about 6 times in 2 years. Panel LED's flashing like a Christmas tree: Pots / Normal / Sani / Cancel lights all flashing Tried different resets as found on web but none work. Dishwasher was NOT being used when the flashing started. Need reset sequence if there is one.


Unusual LED or\015\012Display Readouts\015\012Open ID diodes and/or LED\015\012circuit(s) in keypad, or open\015\012ci ... Whirlpool 24 in. DU1100XTP Built-in Dishwasher

Whirlpool GU2400XTPT Dishwasher is on island of Utila, Honduras. Upon return after several months absence, light was flashing but dishwasher would not turn on, light would not turn off, no other buttons would light up. I am thinking a power surge might have hit it and maybe knocked something out. Problem is, I need a part from here to take down there and hope someone there can install it. Help! Thanks! Barbara Chaney


I had a svc. tech come and he said I need a new "panel". Darn.It's $133 plus labor. He said the "normal" button had shorted out,especially since that's the wash I use all the time. It's only two years old, and I didn't buy an extended w ... Whirlpool GU2400XTP Built-in Dishwasher

The dishwasher keeps flashing a code saying PF and hightemp wash light flashes and also the no heat dry flashes and that is all it does


Hi,\015\012\015\012PF stands for Power Failure.\015\012\015\012You need to Press CANCEL, whenever this message would Display.If pressing the cancel button doesn't get rid of the power failure error "PF" then you have a bad control board.\ ... Dishwashers

Hello, We need some assistance with our Kenmore dishwasher. Last night after I started a load, the dishwasher just stopped and then the washing and drying lights started flashing red, sanitized and green are flashing green and the 6 hour delay button is flashing red. I have pushed the start/cancel button but to no avail. My husband shut the power from it to see if it would reboot, it does not help either. It runs a little bit then quits and does not clean the dishes. Could you give us sugg


Hold the start button for 3-4 seconds and see what that does ... Dishwashers

I have a Zanussi dishwasher model IT 5614. When I turn the dishwasher on, the indicator light is already stuck at "BIO 50" and won't move, and the dishwasher won't start when the door is closed. This just happened today. The indicator light for dishwasher salt was also on, so I added dishwasher salt and that light went off, but the machine is still stuck. The instruction book says that when this happens, technical assistance is needed. What exactly is the problem, and is it anything I can


It has been suggested to switch the machine on/off a couple of times and the flashing light will not reappear. Until this light goes off the dishwasher will not start. All the filters should be cleaned free of any leftover food particles. What i mean ... Dishwashers

Viking professional dishwasher DFUD142 panel lights flashing, and cannot turn of pump, need to cut power, will not go on? worked perfectly 4 yrs. what to do? repair man did not fix.


... Viking DFUD142 Built-in Dishwasher

Whirlpool dishwasher model number GU3600XTSY2 is flashing: The clean light is flashing! It's not the heater circuit either. It says the dishwasher is malfunctioned. Call for service to check heater circuit.Won't start at all.


The clean light sometimes flashes and just needs to be reset. To do so hit the keys in the following order. <Heated Dry> <Normal Wash> <Heated Dry> <Normal Wash> <Cancel>.The dishwasher will go through a cancel cyc ... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

Plumbed in new dishwasher wash light and pre wash light flashing nothing happening ! manual says longer inlet time possible cause -faucets not opened?


Hello lozjojo,\015\012Based on your problem description, you either have no water pressure at the inlet valve or the inlet valve isn't operating and allowing water in. Prior to installation, did you make sure you removed ALL the packing materia ... Dishwashers

My panasonic range microwave NN-S255WF started to randomly beeping and flashing the potato/vegetable setting. For about 15 minutes the microwave keypad would not work at all. It is working again. The range overhead light on the bottom of the unit stopped working about a year ago - light will not turn on. Please tell me what the issue is, what would need to be replaced. The microwave is 4 years old. Thank you!!


We get microwaves in our shop frequently, this unit sounds as if it's brain has been damaged, I suspect, as it usually is that either the magnetron, or the High power Diode, has failed, this usually also, "Spikes" the "Brain" as well. At 4 years old ... Dishwashers

I have a kenmore dishwasher model 58715199400. the clean light keeps blinking. ive seen posts that say to press heated dry, normal wash buttons repeatedly until all lights flash. my model doesnt have a normal wash button, it has a rotating knob instead. any tips?


... Kenmore 24 in. 15199 / 15194 / 15192 Built-in Dishwasher

Blinking lights I have a built in Kenmore 15632 dish washer it has been stopping throught the cycle and the lights will flash on it what could couse this to hapen and what part will i need to fix it


Next time this happens, try pushing in the door handle. If it starts up again, the computer thinks the door is ajar, and it won't run. You'll need the door latch assembly w/ door switches.\015\012\015\012Good luck! ... Kenmore 15632 Built-in Dishwasher

Matsui MF160 integrated dishwasher: Had problems for a while now with the buttons on the control panel ie: on button needed to be pressed down hard for it to connect and sometimes the wash cycle programme buttons would just keep flashing between the three of them and then they would settle down, for the past few days the on button light has stayed on and wont go off and now all the lights on the control panel have gone off and the dishwasher wont work at all, we have tried dis-connecting it, che


... Dishwashers

Maytag Dishwasher I need the reset sequence for my dishwasher. The power comany had turned off the electric to the house to make chages elsewhere in my house. When the electric was turned back on all appliance came back on except the dishwasher. The dishwasher has a front panel touch pad and three of the panel lights are flashing. I know there has to be a sequence to reset the machine. I also need the peace and quiet in the house since I am the husband and am suppose to know it al


We have a model mdvtt53aww1 and you can push three buttons and will light up the hi temp wash, heated dry and sanitize is there a code make it start ... Dishwashers

DU1100xtpt6 stopped working - blinking clean light. Reapir tech says needs new logic board and heating element. Says logic board is under warrenty... can I get board from whirpool with out tech? Where I can buy correct heater? thanks!


If you have "good hands" and a technical orientation, you can manage it by yourself\015\012(board and heating element).\015\012In any case, before buying a new heating element, check element's resistance with a multi-meter, maybe there is no problem ... Whirlpool 24 in. DU1100XTPS Built-in Dishwasher

Dishwasher will not drain. Red light flashing / on. Manual says undo "stopcock". Manual does not say what a "stopcock" is


Stop **** resembles a threaded hole with a bolt screwed into that hole. Basically its a manual drain similar to any cars radiator's drain plug/****. There must be something which is blocking the normal drainage tube, hence the machines is indicating ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0929 seconds