Having problems with your Miele G848I Dishwasher ?

G848 dishwasher intake valve not closing,water running with power off


Answers :

Repair Help & Product Troubleshooting for Miele G848I Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

G848 dishwasher intake valve not closing,water running with power off


... Miele G848I Dishwasher

Hotpoint HDA3400g dishwasher is not running. I have checked to make sure it has power. Took the washer apart, checked that it had power through the door switch to the timer control, all is well. Still not running or getting water into the dishwasher. Any ideas besides replacing the water inlet valve? Will this dishwasher cycle through if it does not have water?


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks for using FixYa. Please check for the following if your dishwasher\015\012is not working-- ... Hotpoint 24 in. HDA3400G Built-in Dishwasher

Kenmore dishwasher. The upper rack is not getting clean. Even very light residue remains. And, detergent is left in door at end of cycle. The bottom is filling up, so I don't think it's the intake valve. Also, all the blade openings appear clear. I am noticing that hot water is not filling the dishwasher when I first run the cycle. Even if I have hot water running in the sink, the dishwasher fills with cold or warm water. So, I think this is the problem. What should I do? Thank you in advance!


I find it odd that the dishwasher is filling with cold water if the water is hot at the sink. It sounds like the dishwasher is connected to the cold water line rather than the hot. Check under your sink; if you've got standard plumbing, the dishwas ... Dishwashers

Miele Diamante G 2150 SCU Dishwasher problem ----The program cycle indicators "Rinse", "Drying" and "End" flash at the same time. The drain pump is running when the door is open. I have reset the power and cleaned the drain pump and non return valve and Spun the propeller several times in both directions to check for obstructions. Still has the same problem. Water is being drained continuously even with power switch on dishwasher turned off.. Had to shut the breaker off to get it to stop. A


Hi\015\012\015\012Plugged system or a jammed drain pump can cause these issues, also make sure the drain hose is not blocked. Check the drain hose for any visible clogging, remove if present. If no visible lint is present then remo ... Dishwashers

Bosch SHU3300 dishwasher stuck on hot water intake (w/ no power)


It sounds like the fill vlave is stuck open. This can happen if your pressure is low or if the machine is old. I would start by replacing the vlave. ... Bosch 24 in. SHU5305UC Built-in Dishwasher

Bosch dishwasher (SXH55MO6UC/46): The power comes on and runs normal, but no water is coming into the unit. I was told that it was a water inlet valve that needs to be replaced (part #263833). I need to know if this is what needs to be replaced and if so, is this something that I can do or do I need an expert repair service to do it? If it is something that I can do, I need instructions. I am handy, but this is something that I have not done before, Thank you, Craig Covey


Hi Craig,Yes it may be the fill valve...but first take off the pipe or hose and check the screen just inside the fill valve...some do not have it but most do...also check that water comes out of the hose or pipe at the valve....THEN ... Bosch Integra® 500 SHX55M05UC Built-in Dishwasher

Dishwasher intake/drain light is on, removed and cleaned intake valve, no obstructions. Tripped the breaker to the power supply to no avail....any suggestions?


Hi\012\012Intake/Drain light flashing means an issue while\012draining. You would need to check for air gap on the dishwasher, it may be\012clogged. It prevents dishwasher from draining, sometimes the drain flow is\0 ... Miele Touchtronic G894 SC Built-In Dishwasher

Hi experts, My Indesit IDL530 dishwasher never seems to run on any of the 5 programmes. On pressing the power button, the red light comes on and on pressing the start/reset button, the light signalling washing comes on and not the one showing water intake. But even then nothing progresses and just a buzz with that wasing indicator on shows for a second and goe off. But today only the buzzer sounds when pressing down the start/reset button and no indicator comes on atll. Will be great if you coul


... Indesit Dishwashers

All of a sudden no water is running in my dishwasher. There is power and heat and the lights work. Have checked hoses and valves underneath sink and checked the float and dont see any problems there.


Hi,Here is a tip the will elaborate on your problem more, but the bottom line is that you need to replace that fill valve...Dishwasher ... Amana 24 in. ADB1500AWS Stainless Steel Dishwasher

Obtained this haier hdp18pa portable dishwasher, thought I would give it a try. The unit will not fill with water, turn the power on you can hear the motor or the pump running but no water comes in. THe 4 display lights flash and beep a series of times and then stop only to repeat the sound off in a every few second sequence. I have tried the remedies offered online, tilting the unit does not seem to work for me on this one. I changed out the water inlet valve but nothing changed and I got the s


HiYou need to clean the filter that is in the tube that gets water in the dishwasherin case you can not find it pls ask me to send you a diagram ... Haier HDP18PA Stainless Steel Free-Standing Dishwasher

I have no power to the dishwasher. I tried the circuit breaker, flipped it. No lights on, nothing. It must have been running when the power might have gone off, may be the power surged or something and it wasn't able to finish running the cycle. I have taken out all my dishes and washed them by hand but I still have water standing in the bottom of the dishwasher. I am a mechanically challenged mom and my husband won't be getting home for two more weeks. The dishwasher is a WhirlPool Gold Quiet


First check and make sure that the units not on a switched receptacle(and is wired into this circuit(i know the dishwasher is "hard-wired",as in the unit doesn't have a plug on it,but it could have been wired into this switched circuit by mistake) un ... Whirlpool Dishwashers

No Power I have a bosch shx33 dishwasher. I just replaced the water valve because of a leak and now I can't start the dishwasher. It's like there is no power to the unit. I know there is power because I get a shock if I touch the two wires that are connected to the water valve. Is there another trip switch or something somewhere?


First let me say that using parts of your body to test for mains electriciy is a VERY VERY bad idea. You are lucky you are not dead. Please do not touch live parts again, get a multimeter or a mains tester.\015\012\015\012If there is mains across the ... Bosch 24 in. SHX33A02 / SHX33A06 Free-standing Dishwasher

Dishwasher I have had above integrated dishwasher which is intermittently tripping the mains fuse. Power is getting to dishwasher and the washing cycles work until a certain point (not the same time) where a loud bang can be heard and the main fuse is tripped. Reset the main fuse and power still gets to the dishwasher and it works again. It has just started to trip the fuse when its not running any cycle (just when power is getting to it). I've checked the fuse on the spur and it looks ok. I hav


Its quite common for the interferance filter to fail on these models its situated in the base of the dishwasher connected to the mains block usually when they fail you can see black dust around it, ... Neff 24 in. S5456 Built-in Dishwasher

Champion dishwasher we have a champion freestanding dishwasher at my church. after the cycle is completed, the pressure guage behind the washer still shows 25-30 and it contnues to spray water. not forced by the motor, but more like a stuck open fill valve. if i turn off the water and run it, then turn the water back on, the valve is closed and does not let water freely in. butif i run it with the water on, it will continue to spray in freely after the cycle light goes out and you open the door.


If you turn the unit off from the circuit breaker will the water still run?if so the guts inside the solenoid valve are worn.you can call champion and get a kit to replace the worn parts and its not difficult to do.hope this helps. ... Dishwashers

My Bosch dishwasher, model SHX46A05UC/30 has been working fine. I ran it once today on the Power Scrub Plus cycle (always use this one). Shortly after unloading the dishwasher I needed to run it again with more dishes. Within a few minutes of running the dishwasher I heard loud, almost grinding noises. Nothing appears to be stuck. Any ideas on what to do? This dishwasher has always been quiet up until today.


... Bosch 24 in. SHX36L05UC Stainless Steel Built-in Dishwasher

Hey guys, I am a dishwasher repair guy in barbados, the caribbean. I am having problems with a Hobart LX30H. the relay board is doing half the things right and the othrs not at all. I replaced it with a new one and the same results. At startup, the wash sump heater and wash motor are running, but the fill valve, drain valve and rinse booster are not running. Hence the startup operation is stalled. the funny thing is that the rinse booster and fill valve led's on the relay board light up at


Not sure what sort of problems (fault codes etc) you were having before you chose to go on the path of replacing the relay board.\015\012\015\012It might help to know what fault codes you have been noticing.\015\012\015\012One ... Dishwashers

Kenmore elite dishwasher valve # 8531325 let water run outside the dishwasher. I removed the valve inlet and nothing seems to be wrong with it. When I start a cycle, the water splashes out the valve through the vent holes. Any ideas ?


It is likely the water pressure is too high for the dishwasher. Can you check if the setting has not shifted to Low pressure. Try to run the dishwasher with mains tap feeding water inlet to a lower setting. ... KitchenAid 24 in. KUDS02FRSS Stainless Steel Built-in Dishwasher

ASKO 1555 dishwasher won't run. The anti flood device motor won't stop running but we've removed all the water. All the lights on the front panel blink in unison and when we hold down the start/cancel button on the front, nothing resets. We can't run our dishwasher. We've tried disconnecting power and resetting the circuit breaker but the churning motor won't stop.


Hello,Welcome to FixYa.Based on your description " The anti flood device motor won\\'t stop running but we\\'ve removed all the water " It is likely nothing very serious. ... Asko 24 in. 1805 Built-in Dishwasher

BOSCH DISHWASHER QUIT MID CYCLE NO LIGHTS ON DISPLAY AND ACTS LIKE NO POWER. POWER INCOMING IS GOOD AND POWER TO SWITCH IS GOOD. TRIED NEW SWITCH WITH NO LUCK. MOTOR WILL RUN IF OVERFLOW FLOAT UNDER DISHWASHER IS LIFTED.


Check the sensor of the liquid at the bottom of the dishwasher. Sometimes that is the cause of the fault. ... Bosch SHU43C05 Stainless Steel Built-in Dishwasher

Maytag dishwasher I have a Maytag dishwasher 2001 Mod# MD85100AWB - Ser# 25257529ZD. I can not get it to run again after the last wash. The lights (clean, rince only, light wash, heavy wash, heated dry) continue to blink and won't clear. I tried to power it down and that did nothing. Do you have a suggestion to what I can do to run my dishwasher again?. Thx, Richard


... Dishwashers

Bosch shu9915uc dishwasher when turned on sounds like drain pump is running but water will not enter dishwasher. When opened the pump sound stops. I did have a plumber over right before this occurred to replace kitchen sink faucet but he said he did not shut off valve to dishwasher and valve IS open.


Hello, \015\012 \015\012Welcome to FixYa.\015\012 \015\012 ... Bosch SHU9915UC Dishwasher

Dishwasher - Bosche - SHV43A03GB - When the main power switch is ON, even with the door open the pump/motor continues to run (ie. Stop-cycle does not operate). However, the wash-program itself does not run, even with the door closed (ie. No water entering the dishwasher, even though water supply is on and feed lines are clear - not kinked). It is like the program is 'stuck' and I cannot seem to get it to reset.


Your door switch is likely faulty and should be replaced. You can get them at partselect.com ... Dishwashers

Bosch SHU43C Dishwasher. Where to get parts - quick? Needs a new control-board / circuit board. All valves, switches, heater appear to work. Won't run open the water inlet valve. Won't run the self-check program. Has a burnt connection on the control 'mother-board'.


1-800-944-2904 That is Bosch Company. They will send out-- next day. ... Bosch 24 in. SHU43 Built-in Dishwasher

My power button cover broke on the dishwasher and I figured out the part number I needed, but when I put it back together I got the wires crossed on the board and door switch. Now the control lights up , but the dishwasher will not run a cycle. THe question is does the plug on the door switch have to be a certain way, because there are three wires and you can connect the plug both ways. I did turn the plug, but it still does not run. Did I break the switch? Bosch SHU9956uc/14


The wires do have to be a certain way on the door. Otherwise a door open can tell the board that's it shut and vice versa. The easiest way to do it, is test the switch with an ohmmeter, place the meter on the switch, push button in and see if the rea ... Bosch SHU9956 Built-in Dishwasher

Hi - my Viking dishwasher has developed a problem where the pump runs continuously, whether the power switch is ON or OFF. After the power is turned ON, the troubleshooting guide indicates that there is too much water in the dishwasher. (One of the pot symbols on the display flashes continuously to show this indication.) I am unable to switch between programs, e.g., from quick rinse to pots & pans. I cleaned all the filters to no avail. I had to secure the circuit breaker in order to turn t


If you open the kick plate, you'll see the pan below the motor and check for leaks. The leaks will trigger the sensor to pump water out. Once you dry out the pan, the pump motor will stop and you should be able to reset the program. ... Viking DFUD042 Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2357 seconds