Having problems with your Miele Inspira Series Dishwasher w/ 6 Programs and 5 Temperatures - G2120 / G2120BL - Blac 24 in. Built-in Dishwasher ?

Hi: I have reviewed the forums and tried to fix this issue. Have a Miele G2120 dishwasher that at the end of the cycle - the three (rinsing, drying and end) orange lights begin blinking in harmony. I have removed the triple filter, and two plastic parts to the impeller and made sure all was free of obstruction. I then pulled it out removed the drain hose from in-sinkerator; removed the water line and checked for obstruction. When it gets into this condition - the majority of water drain


Answers :

Hi

The issue seems to be with the float switch assembly that is bad and should be replaced. Float assembly is found inside the dishwasher's tub, on the bottom. The water that fills your dishwasher lifts the float, and when it reaches a certain level, it acts as a trigger for the float switch. The float triggers the float switch to shut off, thereby shutting off the flow of water into the dishwasher. A defective switch may interfere with your dishwasher's filling and/or draining ability. Use your voltmeter to test the switch. Set the device to the ohms setting x 1. Take each probe and touch them to one switch terminal each. This should produce a reading of either zero or infinity. Continue to touch the probes to the terminals, and press down on the switch's button. The reading should change to the opposite extreme. If your switch fails either of these tests, you should replace it. Hope this helps...please post back for further assistance.


Daniel
Repair Help & Product Troubleshooting for Miele Inspira Series Dishwasher w/ 6 Programs and 5 Temperatures - G2120 / G2120BL - Blac 24 in. Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Hi: I have reviewed the forums and tried to fix this issue. Have a Miele G2120 dishwasher that at the end of the cycle - the three (rinsing, drying and end) orange lights begin blinking in harmony. I have removed the triple filter, and two plastic parts to the impeller and made sure all was free of obstruction. I then pulled it out removed the drain hose from in-sinkerator; removed the water line and checked for obstruction. When it gets into this condition - the majority of water drain


Hi The issue seems to be with the float switch assembly that is bad and should be replaced. Float assembly is found inside the dishwasher's tub, on the bottom. The water that ... Miele Inspira Series Dishwasher w/ 6 Programs and 5 Temperatures - G2120 / G2120BL - Blac 24 in. Built-in Dishwasher

I have a Bosch Diswasher that is not draining. I have disconnected power for 35 minustes and used shop vac to excess water out of drain line. i also pulled all water thru the drain line from the tub itself. i assume that because i could pull the water, all baffles and lines are clear as i emptied the tub from drain line. you can hear the pump come on to drain water but no water is moving. What would be my next step. If it is to replace the pump, how do i easiest access the pump to remove and rep


Either the selector switch or pump is faulty. If there is not any clogs anyways. The system may need to be reset. Most resets are done by entering a series of numbers on the touch pad to enter diagnostic/test mode where the machine can be reset. This ... Dishwashers

I have a hotpoint dishwasher model# HDA1000G00WH. until recently never noticed rinsed water not drained after washing/rinse cycle completed. water level just above the drain cover. i removed the cover to see if i might find something clogging the drain screen but found nothing. i removed the plastic water "return" line & it was not plugged. thinking about pulling the dishwasher out, disconnect the plastic line connected to the bottom of the dishwasher, then remove the "bowel-like" container wher


Take out the pump. You should find a broken rubber flapper indide blocking the outlet tube. Cheap to repair. ... Hotpoint 24 in. HDA3740G Stainless Steel Built-in Dishwasher

The disk washer doesn't drain at the end of the rinse cycle. There is a humming sound but no water is forced through the hose to the sink/garbabe disposal. At the end of the wash, there is a large amount of dirty water in the bottom of the washer. I removed the spray arms, the spray arm holder and the screen and then removed the water, and found a couple of pieces of plastic. But I don't see how I can remove additional parts from the washer bottom. What could the problem be? Is there a fi


Is the dishwasher drain hooked to the garbage disposer? If so is it new? If so did you knockout the plug in the disposer? If so then you either have something clogging the drain or pump. Or the pump motor is bad. ... Dishwashers

Ge profile dishwasher not draining Model no. pdw9280n20ss I checked the drain line at the garbage disposal. No blockage. Line is clear. The back flow loop is high and not kinked. Only a small trickle of water comes out of the disposal drain at the end of cycle. No forceful pressure of water like before. I removed the smaller grill drain area and cannot feel any objects down in there. I do not know how to remove the larger fine mesh grill on bottom. Any suggestions?


Did you ever figure out how to remove that large mesh bit? I am stuck at the same spot and would love a hint. ... GE 24 in. Profile PDW9880JSS Built-in Dishwasher

I have a Whirlpool DU810SWLQ0 that will not drain. I've pulled the unit out, snaked the drain tube, pulled the motor/pump, and pipe assemblies, and cleaned the food trap, which I also removed. I've run the dishwasher with a bit of bleach, and the water will pump in, get processed by the agitator, and be heated. When the rinse cycle comes, dishes get covered in food, and are never clean. Waste water was being used for a clean rinse. I've run the dishwasher with the drain dangling in a bucket,


Refer the wash system assembly dwg. Check if the ball (item 21) is sitting correctly. If it is out of ali ... Dishwashers

My SGS55M72AU/65 does not get rid of its drain water, although that wee pump in the bottom is clearly working (which I could see after removing filters and pump cover). There is no blockage near the drain pipe connection, so I infer there is a blockage somewhere inside the dishwasher, in a place I can't get to without further instruction. I've removed most of the drain water and pulled the unit out, so I could lay it on its side and start taking screws out. But I much prefer to have some guidanc


Ok i am attempting to help you although i dont see your make of dishwasher but im using what i know without manual. to ensure there is a blockage in the dishwasher remove that hose you checked at garbage disposal or vent and leave it disconnected an ... Dishwashers

HI dishwasher will not drain if i remove all the water will run thro cycle and stops with a couple of cms of water left have tryed to find filter inside and failed, removed sides and can see a pump on right hand side can turn impeller easily, is this the drain pump? if not how do i get at pump and or filter. is it possible that plastic chamber on left hand side could be blocked assume this transfers heat Robert


... Bosch 18 in. SRS55L02 Logixx Slim-Line Free-standing Dishwasher

Kitchen Aid dishwasher Model# KUDP01FLSS. 2 problems #1 Won't run unless you press in on the door and hold it for a few minutes then it runs through cycle normally. Problem #2 It won't drain water out at the end of the cycle when I open the door there is water laying in the bottom of the tub. I have checked the drain hose for clogging and it appears normal. I am able to remove the hose from the disposal and suck the water out of the tub using a shop vac this indicates to me that the drain is ope


... Dishwashers

My fisher paykel DD603 fills with water at the start of the cycle and stops with the following error code and a beeping noise: - error U1 spanner symbol - crossed out faucet symbol. The water level is high enough that the spray arm is floating in the water. I am able to drain the water by entering the hardware diagnostics mode and running the motor in the drain direction. By removing the filter plate and examining the impellers I am not able to see visible damage. All filters are clean. The


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks for using FixYa. You are spot on as error U1\015\012indicates that the dishwasher has twice tried to fill with the required amou ... Dishwashers

Hello, I have a Neff Dishwasher S5453X1GB/74 and it's not draining the water out at the end of the cycle. I have unscrewed the filter and released the impeller. I have also cleared the waste pipe that runs to the sink waste and put loads of cleaner in the dishwasher. The pipes seem to be clear as water goes somewhere during the cycle but backs up at the end. A few times when I started a cycle the water did not spray out but I could here the drainer or motor? running. I jetted water through th


... Neff 24 in. S5453X1 Built-in Dishwasher

At the end of the cycle the water is not draining out of the tub. I vac'ed out the water, removed the filters and checked for debris but found non.


Check drain hose first.If you do not find any blockage, then you will need to access the pump, remove pump hose and look for blockage in there.If there is no blockage at all, then either the water level switch, a faulty pump ( ... Bosch SHV46C03 Built-in Dishwasher

GE TRITON XL NOT DRAINING-CHECKED AIR GAP AND HOSE TO DISPOSER. USED BASTER TO REMOVE LOTS OF WATER THAT SMELLED REALLY BAD ON ONE RINSE LIKE BACKING UP. CLEANED SCREEN AND AREA IN PUMP AFTER REMOVING IMPELLER (SP). WATER NOT EVEN COMING UP THROUGH DISPOSER. BAD PUMP?


... GE Tritonr XL GSD6260JCC Dishwasher

DS603 Fisher & Paykel U1 error code ..(see our previous errors we've listed) we have now pulled out the yellow water valve that goes up behind the front panel and at the other end by removing the drawer and plastic protector thingy - we checked that there were no bedris or calcium buildup in the valves ends and filters and replaced it all. So we put it all back to gether as we could not see what would cause this error, only to find that it worked - water came into the machine but about 4 mins in


This product is total ****.\015\012Pull it out, call whoever sold the **** to you\015\012and tell the to come get it and shove it up their ***.\015\012Then buy a Bosch and live a happy life.\015\012The design is moronic. The machine is like the old\ ... Fisher and Paykel 23 in. DS603H W Built-in Dishwasher

Hi, I'm having trouble with my maytag jetclean eq. I've removed everything down to what I think is the drain impeller and can't figure out how to remove what seems to be this last piece. Fwiw, the trouble is dishes are dirty/cloudy, soap dispenser is still half full, and there is an inch or two of water in the bottom, like it never fully drains.


The problem is not your dishwasher but your water actually. hard water is the reason for the cloudiness. www.dishwasherfilter.com makes a filter just for this problem. it f ... Dishwashers

Inlet/Drain light is on. I have cleaned the drain pump and non-return valve, rinsed under water, removes all foriegn objects, turned the drain pump impeller (which turns freely) and carefully replaced the non-return valve and secured it with the locking clamp. I tried turning off the dishwasher and teuned it back on. No warning light shows but as soon as I try the dishwasher on a wash cycle it fails to pump water into the machine and release the washing tablet door. The programme unit makes a no


Is the water inlet turned off by chance? Is there no water at all inside the dishwasher? ... Miele 24 in. G643Vi Plus Built-In Dishwasher

I have a Frigidaire dishwasher. Model FDB520RHS0, Serial TH92539147. The drum fills with water but will not drain. I purchased the unit about 2 years ago. It has been used sparingly and mostly on light wash. I removed the basket and could find nothing blocking the drain. Is there a fix? Can I replace the drain pump? The unit is making a noise as if it is trying to drain but nothing is happening. I have checked the drain line for clogs and it is clear and the terminal end is conn


... Frigidaire 24 in. PLD2560LCC Energy Star® Built-in Dishwasher

Drain pump runs non-stop. Continues when dial is in Stop position. When disconnected for hours, drain pump starts immediately when power restored. In any wash cycle position, drain pump runs and cycle never commences. Small amount of residual water in drain line when impeller cover removed. Board? Switch?


Sounds like the flood switch has activated.\015\012\015\012You will have to drag the dishwasher out from under the counter after turning off the power to it. Tilt to one side so that any water collected under it is expelled. This will fre ... Miele 23 in. Novotronic G841 Built-In Dishwasher

This is a 15972 that does not drain. I think the drain is clogged, how do I access it from inside the machine? I have removed everything to the point of the impeller..... I pulled the drain line from the sink and tried to blow into it to see if that would clear it...did not work.


... Kenmore 24 in. 15992 Built-in Dishwasher

Bosch S9G1B does not drain water away at the end of any cleaning cycle


... Dishwashers

Machine just started leaving dirty water in bottom of machine. cleaned filters,had machine apart,removed and cleaned waste pipe. pump runs and impeller feels ok.only time i could get any water to drain into bucket was when shook waste pipe very hard?


Check that the pump is clean and not loose. Make sure pump, impeller, and waste pipe are in alignment with each other and are clean. If it works when you shake the pipe, then there is still a clog inside or the pipes aren't aligned correctly and some ... Dishwashers

I have a Bosch SGS46E22GB Exxcel dishwasher. It is failing to drain or pump out dirty water. About a year ago we had this fault and the engineer replaced the impeller jug. He showed my wife how to clear a blockage with the left hand side panel removed. I can't get the panle off so am looking for instructions on how to remove it. Thanks


... Dishwashers

How do you remove the impeller from the main pump on a Hobart C44AW. I have taken the nut off the end of the shaft but I don't know if the impeller pulls off or screws off.


It pulls off. Just use a small/medium sized gear puller and it'll come easily ( there is a lip on the impeller for the purpose of pulling). ... Hobart 40 in. AM14-254 Free-standing Dishwasher

Does not drain water out at end of cycle, I have tried cleaning out all the screens,have opened the impeller cover and checked that the impeller is clean and free. When I put together, it runs for 2 or 3 cycles before the unit has the problem again.


Hi\015\012\015\012\015\012\015\012\015\012\015\012Thanks for using FixYa.\015\012Dishwasher not draining properly or not draining at all issues can arise due\015\012to different reasons. Usually, these issues are related to kinked h ... Bosch 24 in. SHX33A02 / SHX33A06 Free-standing Dishwasher

I have a Maytag MDB7100AWW dishwasher that makes a lot of noise from the motor at the end of the drain cycle. When there is water in the dishwasher it doesn't make any noise and washes well. This url (http://www.applianceaid.com/maytag-dish-noise.html) describes my problem exactly but I can't remove this part. I have unscrewed the 3 screws keeping it in place but it seems to be still attached to the motor. How can I remove it?


... Maytag MDB7100AWB Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1706 seconds