Having problems with your Moyer Diebel 401HT Dishwasher ?

The temp of the water is 200 degrees.How do I turn it down to 180


Answers :

If the temperature was ok before, and no one has adjusted the thermostat, then that is an indication of a thermostat that needs to be replaced.
Repair Help & Product Troubleshooting for Moyer Diebel 401HT Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

XL30 Hi temp. Two problems: 1) Hi temp booster not working...worked on and off for awhile, now won't get up to 180. 2) Turned on today and water flooded out. Water overfilled machine, turned off and heard pump drain unit.


To attempt to solve the over filling, clean the probes in the back right corner. Use a green scrubby pad.\015\012\015\012There is also two probes under the front screen. Clean them too.\015\012\015\012As far as the booster not ... Dishwashers

Purchased in 2003. Dishes were exquisitly clean till 2008. Our water heater temp was set at 140 temp. This heater was replaced with a heater now set at 125 temp. In the past two years dishes are nowhere as clean on the the normal start setting. Should I go to the Pots and Pans start setting to get hotter water or should I turn up my water heater? All this is assuming that water is not hot enough. Does the washer heating element ever burn out?


Try turning on your water at the sink for a while on hot let it run then start the wash cycle that should help. what that will do is let the cold water run out of the pipes and therefore you will have a hot water start. ... Kenmore Dishwashers

Fills ok wash ok at 156 degrees goes into rinse cycle dont seem to have much water comming out shows 0 degrees rinse temp. screen is out so thats not clogged have separate free standing electric heater piped in has been working fine for 5 years that way dont understand 0 degree water temp. on display any help would be great thanks for your time joe


... Hobart AM14-253 Free-standing Dishwasher

I have an Indesit IDL 42 dishwasher. It has entered a state in which it behaves like this: as soon as I turn it on, it starts swishing the water around (it doesn't pump it out) and it does that regardless of whether I press any buttons (I have tried Start, Reset, turning the program knob, no difference at all). When I open it in the middle of this cycle, the water drips, and there is plenty of water (about 1 in) at the bottom. I have checked the filter, it is clean. Can you please help?


... Dishwashers

Dishwasher wont turn on dwa73a Amana built in. I turned off circuit breaker and now there's blinking lights on the air temp and water temp. Never use these buttons. I can't get any button to work much less get it turned on.


Hi\015\012\015\012You will have to first check/test the door latch assembly,\015\012if that is fine and the door is closing properly then it means that the control\015\012board is bad and should be replaced. Hope this helps...please post ... Amana 24 in. DWA73A Built-in Dishwasher

Miele dishwasher optima G 2420. during instalation and test for water hardness display shows 'P' then '1' then '0'. is this a water hardness of '1' or of '10'


... Miele Optima G2470SCSF Dishwasher

I have a Karcher 3.99 Pressure Washer. The motor appears to be working and water is passing through the machine when turned to the detergent application setting. However when the lance is tightened to turn on the pressure, no water is coming through. The Karcher is just over 1 year old David


Hi I have a karcher 3.99 the motor comes on and water comes out however thre is no pressure i have tested the lance on my brothers washer and this is ok what is wrong ... Karcher K 5.85 M Electric Pressure Washer

When dishwasher is turned on to the cycle mode - it fills with water - heater heats water to the proper temp - pump starts - washer goes through it's complete cycle - even pumping out the wash water and the drying cycle,then shuts down. the problem is that it does not circulate the wash water thru. the spray heads-even though the circ,pump is running.Even though the unit is 8 yrs.old and hasn't run for 6 yrs,my wife&i do our dishes by hand. our unit is a GU1200XTKB0 Serial# FL4617501


The impeller on the wash pump is worn out or the disposer screen is obstructed. Disassemble as needed to investigate the cause. ... Whirlpool 24 in. GU1200XT Built-in Dishwasher

Keeps on filling with water when turned off


Water in let valve ... Whirlpool 24 in. GU1200XT Built-in Dishwasher

Problem: dishwasher (moel MDB6601AWW) will not run. The front panel has a light, between the "Delay 1-9" and "heated dry" buttons, and adjacent to small printed icon (looks like a tombstone with the number 3 inside). Last weekedn I shut off all the water in order to change a faucet, including the hot water feed to the washer. Now the fed to the washer is somewhat frozen -- I can only open it 1/8 turn. So, I wonder if my wife tried to run the machin with no water flow, and it shut itself dow


... Maytag 24 in. MDBH955AW Built-in Dishwasher

KitchenAid KUDP01DLBS2 dishwasher. Runs for a very long time on any cycle; time does not seem to advance. (takes 2.5 hours or more for normal cycle. "sensing soak", "water heating" lights on for a long time, even though it appears that water is not being heated. Checked incoming water temp, is hot. Did not do this when new, something has changed. Typical cycle was 1 hr 10 min. before.


Sounds like the heater inside the dishwasher is not working. The machine is trying to get the water up to a preset temperature, probably in the neighborhood of 140 degrees. That is one of the things that it is sensing.After the machine fi ... Dishwashers

Hi, The machine will not complete a cycle. I think it may have started when the power was turned off at the mains during a cycle. Symptoms are : - You can turn machine on, select a program, press start button, close door, machine appears to begin cycle as normal, water seems to load, then 2 minutes later drains, and 1 minute or so after that the machine beeps 3 times to indicate cycle is finished. Dishwasher tablet door never opens, dishes not cleaned. Have tried : - cleaning filters; - turn


It is likely the dishwasher is locked in some diagnostic program.\015\012If you provide the dishwasher model no. then I can try to find out the keys you need to press to get it out from it. ... Whirlpool Dishwashers

Extremely heavy limescale residue on all items after dishwasher has finished. water temp in house has been turned down. Had water tested by city water company and results were clear. 12 months ago maytag replaced heater element under recall, but dishwasher always seems too hot. Neighbours do not have this problem. Any advice would be most welcome.we only use quality powder and rinse aid. Have cleaned dishwasher numerous occasions. model MDB4651AWS1 SERIAL # NW5015848


Hi,The scum, film and white residueproblems have started since the reductionof phosphates in dishwasher detergents.Here is a tip that will help you to solve the problem of films, residue, and scum in your dish ... Maytag 24 in. MDB4651AWS Stainless Steel Built-in Dishwasher

I have frigidaire dishwasher,starts cycle,can hear water entering dishwasher,checked level of water,does not get to 1",machine starts washing by the sound of motor, but dishes are not clean,water drains machine turns of,cycle complete.what do you think.


Depending on your dishwasher, it fills either by a timer or by a water probe or float. I will assume its a timer as a probe or float wouldnt exhibit this behaviour. I would say you have a restriction in your water supply line. Check your valves, an ... Frigidaire Dishwashers

It won't turn on. Two lights, the Water Temp


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks for using FixYa. Please check for the following--\015\012\015\012 \015 ... Amana 24 in. DWA73A Built-in Dishwasher

Dishwasher cycles through all programs but will not drain or turn off at the end of cycle. I do not know if it drains inbetween. It just continues to run on 0 minutes and when I turn it off and open there is standing water


Underneath the machine there is a donute shaped styrofoam item called a flood safty switch .makke sure there is no debri underneath..mice will drag animal food or chew on this and will lodge it leaving debri under it causing it to trigger a false flo ... Bosch 24 in. SHU43 Built-in Dishwasher

Hobart LXIC under counter comerical dishwasher. Delime lled keeps comeing on every time power up. Checked sensors on bottom in the water drain area senser on right (there are 2 next to each other on this unit I think other is water temp) the wire had wire burn completely off. I reconnected the wire and started to burn up the wire again. Question: 1) Is this sensor for the Delime sensor? 2) does it sond like the sensor is shorted to you? or sending wrong voltage to sensor? 3) If no


... Hobart 24 in. LXIC-5 Built-in Dishwasher

Hello I have a Miele G1235 SCU economic model, my problem is the departure of the machine. When you turn on any water stops after 1 minute and I get error f14.Ho clean the inlet water, but always crashes! Thank you for your attention! Angelo


... Miele Premier-Plus Built-in Dishwasher

Siemens auto 3 in 1 dishwasher stopped working. lights are on. Machine is humming for a while, but no water enters the machine. Water tap is turned on, filters are clean, no bends in the hose. timer is counting down as during normal washing cycle, but nothing happens


... Siemens 24 in. SE25A266 ExtraKlasse Free-standing Dishwasher

I have a Bosh Logic dishwasher SGS65L12GB/04 The other day it got to 1 min left and would not stop pumping out water and continued even with the door open. After 5 mins playing around it started working again for a further 2 washes. Now when switched on the pump for pumping out the water works continuously. Reset it time seem to count down but does not do anything reset time goes to 0 and beeps but still the pump runs even with the door open. all buttons seem to work fine but no washing and pu


Hi Jonathan,\015\012\015\012Welcome to FixYa.\015\012\015\012Your float may have got stuck or it's possible that you have water leaking into the bottom of the washer. In the bottom of the wash compartment, next to the drain yo ... Bosch Dishwashers

My new bosch dishwasher doesen't clean the top rack of glasses, ran it 3 times, no difference. also the soap dispenser opens up but the powdered detergent won't dissolve, the same soap has been in the dispenser for 3 cycles. i turned up the water heater temp to try to fix the problem it seems to have no effect. the dishwasher is 2 weeks old. could my water supply line be too small or are they a stndard size. thanks


... Bosch Dishwashers

After starting wash cycle the rotary dial advances to what appears to be the second phase and stops at about 1 oclock position. I replaced the timer/switch, same problem. Could I have a water temp sensing problem due to a poorly adhered sensor? I thought this may be the issue as the sensor at the water feed near the soap dispenser was loose on inspection. Model Bosch SHU4002UC/U06 Under counter Dishwasher


Check the thermostat sensor. If the sensor is faulty the amchine will not detect that the right temperature is reached and the cycle will not advance.The thermostat will read low ohms (about 1K) using a multimeter at Rx1 at ro ... Dishwashers

Dishwasher fix water does not go through the spray,. the upper hand an lower hand are clean , the pump does operate to empty the dishwasher . I do smell like some burning smell when I turn the dishwaher on, the water start running for 1 minute or 2 than stop shortly and doesn t reach the arm then the dishwasher becomes hot inside . Thank you


Something has gotten passed the screen and is jamming your pump impeller pull lower spray arm pull screen and see if you can find what is jamming the impeller and remove it drain pump is separate ... Maytag MDB7100AWB Dishwasher

501ht goes thru wash cycle but cam stops just before rinse cycle clicks in - stays in wash cycle - turned thermostat to booster down in temp -cam then keeps going properly but with no hot water from booster - replaced thermosat still same result - apparently a safety ? no booster water no rinse?


Did you get a solution for this? I am having the same issue. Please email me at [email protected] Thanks -Eric ... Moyer Diebel 24 in. 501HT Built-in Dishwasher

Zanussi DA6141. Dishwasher will not progress from turning on at wash code c1. Test 1: No kinked hoses Test 2: Put water in by hand and it empties it. Lift out the central sieve/filter and it all appears very clean. Test 3:Inlet water filter clean. No actions except low buzz (?solenoid?) after emptying. (Possible Hint: Previously this washer sometimes stalled with knob rotated 15 degrees clockwise from C1 position and would continue to wash dishes indefinitely, if unattended. This was


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks for using FixYa. If the\015\012cycle doesn't complete, check these:\015\012\ ... Zanussi Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1070 seconds