Having problems with your Neff 18 in. S5943 Slim-Line Built-in Dishwasher ?
My dishwasher keeps stopping halfway through a programme - think its an electronic problem??
Repair Help & Product Troubleshooting for Neff 18 in. S5943 Slim-Line Built-in Dishwasher
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
My dishwasher keeps stopping halfway through a programme - think its an electronic problem??
... Neff 18 in. S5943 Slim-Line Built-in Dishwasher
Whirlpool Dishwasher ADG 450. Start as normal and it keeps intermittentlly stopping and starting. Washs / drains fine, but sometimes cycle seams to last for a couple of hours. I think it is four beeps when it is stopping and then immediately starts again. We had a problem months ago where as the sink was draining into the dishwasher out pipe, so dishwasher wasn't draining / filling up. Fixed the problem by turning the pipe the other way so water couldn't flow that way - but I don't know if that
Carlton Cs1w. Hi I have a Carlton slimline dishwasher. No problem with filling, heating and emptying. But if I set it to full programme it sticks. Starting with pan setting and letting run right through programme it just keeps sticking. On last programme timer moves ok for first 10 or so minutes then gets no further. Tried different settings, checked everything I can think of and cleaned added salt etc. Got given. Last owner only used a few times, moved house and no room for it. But was sitting
Dishwasher keeps running I have a Bosche dishwasher and the water keeps running. As long as we run it and don't stop it, the pump will continue to drain about every 3 minutes. The water just keeps running though. If we open it to empty the dishes, the cycle will stop. But the water keeps running, filling the tub, and then overflows, flooding the kitchen and drains through our wood floors to the basement below. Our ASKO seems to have a similar problem. I started the dishwasher, and the water ke
Open up the door, get out the control unit. Pry open the unit's plastic case and look at the board. Burnt spot? If so, the heater circuit burnt out (happens a lot on Bosches) and the control is waiting for the water temp to rise, but of course it ... Bosch SHU43C05 Stainless Steel Built-in Dishwasher
I have Whirlpool dishwasher about 3years old it is the ADP7966 AAA 6th sense. When I put it on and turn the temperature knob, only the first temperature green light comes on althou I can turn the knob all the way round none of the other lights come on, my rinse aid and salt programmes light up thou ,and when I press the start button it flashes twice stops a bit then flashes twice again, and thats all it keeps doing. I would be very grateful if you help to solve the problem. Many thanks to you.
Hi threr I have the following problem with my Haier DW12-EFM dishwasher: The dishwasher seems to operate properly for the first several minutes untill program selector knob stops betwin position 2 and 3. After I turn it manually it keeps on turning and than it stops again after I turn it again it operates till the end of the program but the dishes are not clean enough to be used. I also noticed that the heater does not operate (water is cold). Do you know wht the problem might be. Reg
... Haier 24 in. ESD100 Built-in Dishwasher
Westoint Dishwasher I have looked in the manual under troubleshooting tips, but didn't find anything on the problem. The dishwasher goes into cycle,but during the wash cycle it stops,makes alarm and the wash and rinse ligts come on. And now I can't even find the product on this site.Westpoint Dishwasher WQP12-9240. Thankyou My dishwasher is stopping at stage 2 of the programme after beeping once. Quite often the detergent flap doesn't open. Am at my wits end and threatening to leave home!!!! Th
Hi again,\015\012\015\012That should be OK. Just get in touch with your sales rep or his boss. Somebody there will be able to look up the record of the purchase. If they ask for model & serial numbers, you have them. You will find ... Dishwashers
Hoover dishwasher stops and keeps beeping halfway through cycle
... Hoover Dishwashers
Dishwasher problem Our Asko 1353 dishwasher stops halfway through its's wash cycle. I suspected the thermostat, as it seemed loose in it's holder and not tight against the tub. After I tightened the holder the problem is still the same. Also, the on/off switch (pressure switch?) does not stay in the on position and when I looked it over I found one of the crimp on terminals had melted. Short circuit? Too much resistance from bad thermostat? How do I check the thermostat before I order a new one?
I think your switch may just be bad,but to check the t-stat remove both wires and use a multimeter,set the meter to ohms and connect the two leads to the terminals on the t-stat.with the t-stat to off you should read an (ol) open condition,when you t ... Dishwashers
I have F&P DD603 with problem with bottom draw. Once a programme is selected and door is closed, the dishwasher beeps three times then tries to start itys cycle. It then starts but stops every 1-2 minutes (like pause botton has been pressed). If you press start again it starts for 1-2 mins then stops again. I have tried turning off the power and totally cleaned out the dishwasher but no change? Any suggestions?
Hi \015\012When you pull out the drawer, pay attention to the bottom near the bottom front panel, you will see a little tab. this tab is at both sides of the drawer, press these tabs in and pull the drawer fur ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher
Bosch dishwasher I have a month old Bosch dishwasher. It was stopped mid cycle. I drained the water at the bottom, but the active light keeps flashing, and when I press the start,reset button, then turn it off, it does the same thing when I turn it back on. active light keeps flashing and the wash light is on. It won't even lock the door. How do I fix this because there is no Bosch dealers here to help with the problem.
... Hotpoint 23 in. BF41 Built-in Dishwasher
Hi my nearly 9yr old neff S5555 integrated dishwasher has problems on the control panel the program times come up with the completely the wrong times for the wash ie the 150 one comes up saying 32minutes on a quick wash it gets stuck at 1 minute left and keeps going on, also the delay timer timer is not working ( I have been told this could be a problem with the programmer) . Is it cost effective to get the progammer changed plus engineers cost or shall l look for a new dishwasher? Thanks Su
Hi my nearly 9yr old neff S5555XOGB/40 integrated dishwasher has problems on the control panel the program times come up with the completely the wrong times for the wash ie the 150 one comes up saying 32minutes on a quick wash it gets stuck at 1 minute left and keeps going on, also the delay timer timer is not working ( I have been told this could be a problem with the programmer) . Is it cost effective to get the progammer changed plus engineers cost or shall l look for a new dishwasher? Th
... Neff 24 in. S5543X2 Built-in Dishwasher
I have a 4yr old Smeg freestanding dishwasher. Model is DF612SDX. The problem is that a wash cycle will start but about 15 mins in it stops and 2 of the programme option lights (on the left hand side of the programme options), start flashing. If you open the machine the soap dispenser has failed to open. This problem has been a bit of a slow deterioration as we've had a number of washed that have managed to finish and then noticed that although the dispenser has opened it must have been to
... Smeg 24 in. DWF612SS Free-standing Dishwasher
My Delonghi Dishwasher keeps turning off. The dishwasher is turned on at the power point. The water is turned on. Okay When I press the POWER botton on the front it wont stay on. I have to keep my finger on the POWER button and then press the START button for washer to work. If I do this it will then pump out any water in the bottom and start to work. ***BUT when you take your finger of the POWER button the washer just turns off and stops working. Do you have any idea what could be the problem p
Yes, the power button is faulty. by pressing the power button forcefully, you are in effect allowing the contacts to close. Replace it. ... Dishwashers
A GE triton dishwasher causes hammer noise when stops filling. The sink faucet works fine as do all the other faucets in the house. I cleaned all of the traps in the dishwasher. Because the sink works, I don't think it is a sink valve problem. I turned off the water to the house and drained the system, the air chambers should be good. Is there some component of the dishwasher that could be causing the noise? Would cleaning the pump help? If so, how would I do that?
The cause of the hammering noise, (slamming) is due to the water inlet valve on the Dishwasher (DW) shutting off abrutly once the DW reaches the proper amount of water.\015\012\015\012If this is an older DW, you might want to replace the ... GE Dishwashers
My LG dishwasher upper rack has stopped cleaning. The uppermost arm is seemingly getting no water at all and the arm on the underside of the upper rack is getting some water, but not enough to turn it. I have already disassembled and cleaned all the way down to the diverter assembly and it has not fixed the problem. I think this is a problem with a the (?) diverter pump or perhaps a sensor that sends water to the upper arms. I am trying to figure out how to further diagnose the problems. The
Hi,\012\012\012\012\012I\012have an older dishwasher also and recently my wife also complained\012about it not cleaning right... so me being the man I am tried in vain\012to clean the things... Bought new ... LG LDF6810 Built-in Dishwasher
Beko Slimline Dishwasher DE2541FW - Eratic Behaviour & Programme Failure (also filling problems)
Location UK? Do not use tabs please. Only loose powder is best.I have seen so many dishwashers fail because of wrong detergent. You need a new control board. Or microprocessor board you say in the UK? ... Beko Dishwashers
Hi, Dishwasher problem: When a programme starts, the machine fills with water then stops and the "check water" light comes on. To empty the machine, I used the reset programme which does empty the machine. Any ideas of about what might be causing and the solution to this? Many thanks, Richard
You will need to check the inlet valve and the water level pressure switch. It can also be a low pressure in the pump that is giving out the signal for the control board to shut off.\012So first of all check the water line throughly to confirm. ... Bosch 24 in. SGS43C12 Classixx Free-Standing Dishwasher
Smeg dwd 64 sse. everytime I put it on a full cycle it starts at the 2nd light and just remains on that programme and sometimes does not even stop I have to stop it manually. do you think its the pcb that has gone and is it worth replacing on a 6-7yr old dishwasher?? always been good up till now
... Smeg 24 in. DWF614SS Stainless Steel Free-standing Dishwasher
Dear Sir/Madam,I have owned a Beko DW450 slimline dishwasher for 13 months and used it only twice, i wanted to use it last night but when i switched it on the drain pump activated and would not switch off. I powered down the dishwasher to see if that would reset it but unfortunately when i started it again it did the same thing - drain pump activated but would not stop running, it is impossible at the moment to carry out a wash programme. Does anyone have any idea on this problem. Thanks, Patric
... Bosch SHU5315UC Dishwasher
Have a Zanussi 6344 dishwasher, when starting the machine it starts pumping en then stops. When adding water the same problem, starts pumping to drain the water and then stops again ? It drains perfectly, seems the machine thinks there's still water inside, is there some sensor that checks the water level or so ?
... Kuppersbusch 24 in. IG6344 Built-In Dishwasher
A feew weeks ago Smeg STA6047 dishwasher stopped in the beginning of the programme after approx. ten minutes, and gave the error code E9. There had been clearly water in the machine, but maybe not enough and the detergent box was not open. However, when technician came by two weeks after, the dishwasher worked and he said it was in order. But only after being used only once, the same problem reappeared. First the washer gave the error code E8, on the second try E9. And now it does not start at a
As you know E9 is linked to the water inlet problem. \015\012\015\012There are two scenarios here - 1) Are you using the Aqua-Stop safety system? If this is trigerring then it can shut the inlet water. The reason it can trigger is if the ... Smeg Dishwashers
Matsui MF160 integrated dishwasher: Had problems for a while now with the buttons on the control panel ie: on button needed to be pressed down hard for it to connect and sometimes the wash cycle programme buttons would just keep flashing between the three of them and then they would settle down, for the past few days the on button light has stayed on and wont go off and now all the lights on the control panel have gone off and the dishwasher wont work at all, we have tried dis-connecting it, che
My Kitchenaid dishwasher Model KUDPO1FLSS3 stopped working. The electrical works, as we checked the breaker and the little lights on the panel turn on, but the machine will not start. We're thinking there might be a problem with the connection where the door closes. We've checked out everything we can think of, but no luck. The plastic panel is worn away in places, so some of the buttons are exposed-can't imagine that matters, though. Help!
... KitchenAid Dishwashers