Having problems with your Neff 24 in. S5443X2 Built-in Dishwasher ?

Modell S5443X1GB water not pumping out,no

\015 Modell S5443X1GB water not pumping out,no blockages,pump not obstructed,seems to be programmer problem?any ideas\015

Answers :

First you need to ensure that the drain pump is working.
The drain pump is tested by the technician by energizing the pump directly, so to understand if the pump solenoid is working.
This is an unsafe job for the home user, as there is AC inside your appliance, all live power test should be done by techs.
Apart testing the pump, check also the wiring harness to the pump.
If the pump is fine, then replace the control panel.

Here you find parts for your appliance and repair help.
Repair Help & Product Troubleshooting for Neff 24 in. S5443X2 Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Hello, I have a Kitchen Aid (model # KUDMO1T JWHO) dishwasher that runs the motor in all cycles, with water fill & drain working fine, but the pump is not pumping water during any cycle, as the spinners and the inside of the washer are dry when I open the door, except for the water sitting in the bottom. Also, no normal swishing sound of water when the motor runs in any cycle. Looks to me like a mechanical break in the pump drive. How do I check the pump drive on this model? Do you have any


... KitchenAid Dishwashers

I have a DeVilbiss pressure washer, Serial# 2251136878, Model# WVRH2421, Radial Pump# D28703, with a 5.5hp honda motor. It has no pressure. If the pump can't be fixed, is there another brand of pump that will fit this model pressure washer?


THE PUMP FITS THE MOTOR and the pump i always use is a ROYALPUMP made in Italy and they are long lasting and easily serviced ,any of the Italian pumps are good ... Pressure Washers

If the pump is broken, should the engine start? if i choose to rebulid pump where do i find the torque values/guidlines for the pump. i have to get the model #, but i do have the dewalt 3800 psi model. purchased 2 yrs ago.


If the engine turns rather freely and not hindered by malfunction of pump, then it should start. Since you are going to rebuild pump, you should just remove the pump from the engine now and set it on the work bench to prevent any further damage. It ... Dewalt 3800 PSI Pressure Washer

I have a honda pressure washer. Cart serial # 2151076370 cart model # 2221SCVH pump serial # 0000231983 pump model # D2150231983 The problem I am having is that it will not build pressure.


... Honda Pressure Washers

I have a Briggs Stratton Model# 020228 Gasoline Pressure washer with a Faip Brand Pump. The engine starts, the water supply goes thru the pump under its' own pressure. When I pull the trigger on the handle, there is not increase of force nor does the pump engage. I had this same problem several years ago and sent it to a dealer for service. His service tag indicated a stuck unloader. Where is the unloader located on this pump. The indentification on the pump is MTPV90736 191693 Order # 52


... Briggs & Stratton Pressure Washers

Troy-Bilt 2550 20293 pressure washer not producing pressure. Worked when last used 2 months ago. Pump pistons are moving up and down when engine is pulled through. Inlet water is flowing through pump but no pressure when engine is started. I have the same problem. Water flows thru the pump when not running, but no flow or goes in by-pass mode when I start the pump. The pump being Troy Bilt Model 020296-01. I replaced unloader valve even. Anything else I can do?


You replaced the unloaded valve. Are you positive you have the unloader screwed to pressure and not turned the opposite way? You will have no pressure if it is adjusted wrong. One other thing I have encountered is that the unloader has a ball bearing ... Pressure Washers

My pump is gone on my pressure washer. The honda engine is GC 160. The pump is a model VRX2527G. How do I pull the pump off the engine to replace it. I removed the four bolts from the pump housing, but the pump is still tight to the shaft. Please explain the removal process.


Hello,Your pump sits on a keyed shaft, versus a taper fit. This is good, since tapered shafts will require a puller to remove the pump.Since the pump is already bad, you have a few options available to you. 1) W ... Honda Pressure Washers

Parts diagram for cat pumps / ******* pumps model number 66DX40G1I


... Pressure Washers

We recently purchased a new pump for our frigidaire gld4355rf dishwasher. The old one started making grinding noises. When we moved the dishwasher it had leaked due to a failure of an interior seal. Our new pump is now making the same grinding noise but it is not constant. When my husband adjusted the pump by using his hand when he got into a certain position the noise stops. We keep the screens clean. Is there an issue with the pump in this model?


... Frigidaire GLD4355RF Dishwasher

I have a bosch dishwasher model she46c. the float stuck and the pump ran and almost burned out smelled burnt. got washer to restart everything works but pump is noisy. replaced pump but it is still noisy. What do I need to check? nothing is stuck in pump. thanks ron


... Dishwashers

GE Dishwasher model PDW8200J03BB stopped draining. Removed the drain pump, checked with Voltmeter and there is resistance on ohms X10 of about 3. The flap is in place so water isn't shooting back into the sump inlet. Replaced the sump inlet about 6 months ago because it was deteriorated due to hard water. Pump worked fine after that. Checked drain hoses and air gap. Was able to blow water through. Pump only trickles water out at air gap. Does the pump need replaced?


Clear the line from the air gap to the drain,, if the rest is clear the only thing it can be is the propellers on the pump, i which case you will need to change the pump ... GE 25 in. Profile PDW8200J Built-in Dishwasher

Bosch dishwasher model shx36l fails to stop pumping. The drain was clogged. I cleared the drain. Dishasher backed up, water overflowed. Clog has been fixed. Dishwasher will not stop trying to pump water out. There is NO water inside dishwasher. I wish to run another load however unit fails to respond. Pump is operating even when front door to doshwasher is open. Turning the power button to OFF is the only remedy to stop drain pump from operating. How to fix?


... Bosch Integra® 500 SHX46A0 Dishwasher

Have GE Dishwasher model GLD6700N20WW,unit has stopped draining! Took apart and pump was running when check, but no water coming out. Checked drain line and pulled apart pump housing, all clear. Thought maybe pump has a silinoid built inside of it and was stuck shut, so bought new pump and same thing, no water will go thru! Please help me? Is it control module, or turbitity sensor possibly?


... GE Profile PDW8600J Built-in Dishwasher

My Bosch dishwasher circulation pump stays on through all cycles. No leaks and pump works. Other then the circulation pump remaining on, the machine goes through all cycles normally. Any suggestions? Model shu 9920


... Bosch 24 in. SHE43C05UC Stainless Steel Free-Standing Dishwasher

Dishwasher model: se6 tie1 Fitted under kitchen work-top. Problem: After setting a program & switching on & closing door ? there is a normal sound from within but if door is opened there is no evidence of water being pumped in. I previously cleared food debris from the drainage pump area (including under the pump cover), checked the spray arms and checked the water supply was getting as far as the long in-take pipe. As it seems problematic to remove the (screwed in) dishwasher, I have not che


... Dishwashers

Pump is pulsating , not pumping full pressure , water supply and screens checked out ok pump model sjv3g627-1 on a briggs 6.5 hp


Pulsating is usually due to a leak. It could be the pump leaking or the hose, gun or wand leaking. Is there water coming out of these anywhere it is not meant to? It could also be a valve is not closing properly or a seal needs replacin ... Pressure Washers

I have a model 665.1576 or 1676 my paperwork does not have the number on it and no part number on he machine, but I ordered parts from the catalog which matched. about 7 years old, stopped draining, so I changed the Seal kit, pump base seal, impeller, plus drain cover gasket but not the pump gasket could not find it, reinstalled, pump works but much slower and times out, have to hit drain button to get all water out. Keith


... Kenmore Dishwashers

I have two questions and would greatly appreciate some help: - What oil to use in the pressure pump of a Ryobi Pressure Washer RY80030? - How much to put in? The pump model is MTP092150 from FAIP. As per the manufacturer, the oil is not to be changed or topped up by the end-user, I know, I know, but brought to a service center instead - I certainly don't want to do that, and there is none close to my place anyway. The reason I need this is that I had to take the pump apart and a


... FAIP Non Marking Pressure Washer Hose 4000 Psi, 50ft. Length

Our GE model GSD4320Z00B is having a problem with the drain system. I've run the unit in the test mode and it does pump the dishwasher down. The problem is the unit does NOT pump down during a normal wash cycle. The fact that the unit works in test tells me it is not the pump. I've checked all the hoses and drain paths and there are no obstructions, again verified by the fact it works in test mode. Any test that can be used to determine the problem besides replacing parts one by one?


... GE 24 in. GSD4320Z Built-in Dishwasher

Dishwasher (Whirlpool Model DU930PWQ0) won't pump out. Problem occurred after door was opened during a cycle. Then the pump-out function ceased to work. Washer fills and pumps correctly during the wash cycle. Any suggestions? My guess is that the electronic control may be faulty and it is not opening the solenoid valve for the drain cycle. The other option I have thought of is that the solenoid valve may be faulty and is not responding to the signal from the controller. The dishwasher is n


... Whirlpool DU930 Built-in Dishwasher

Is there a general reset code for this model? Problem seems to be that it pumps out,then fills thendoesnt advance in the program.There is a clicking occasionally then it waits 5 mins then a short pump out again followed by a long pump and refil Just lacking the actual wash..+no spray


Please confirm if there is still a problem with the dishwasher. Are you expecting any further suggestions ? You should post a comment as soon as you find the torx screw driver and are able to investigate the component. ... Dishwashers

Full model number is SGS45E08GB/56 Will pump out water if you pour it in manually. Takes in water - sometimes. Main pump runs but no water flowing out of arms. Float switch is not operated and is not defective (tested off the machine). Intake solenoid valve seems to work properly (tested off the machine). Pump continues to run even if door is opened.


... Bosch 24 in. SGS45E02 / SGS45E08 Exxcel Free-standing Dishwasher

HI, I have a Karcher Model K2400 and the pump stopped working. I took it apart and found the 'cheese head' screw had broken. there didn't appear to be any other problem with the pump so i am replacing the screw only. my question is how much pump oil should be put in the reservoir upon assembly as there doesn't appear to be a fill/drain plug?


... Karcher 2500 PSI Pressure Washer

I HAVE A GE DISHWASER MODEL#GSD2200G02WW I WANT TO CHANGE THE PUMP BUT CAN'T FIND A REPAIR MANUAL I CALLED A REPAIRMAN AND THEY WANT $300 TO CHANGE THE PUMP CAN ANYONE TELL ME WHERE TO GET A REPAIR MANUAL OR TELL ME HOW TO CHANGE THE PUMP IT DOESN'T LOOK THAT HARD PAUL


... GE Dishwashers

Hi ..I have an Excell gas pressure washer model no. Exwgv2121-3 with Faip 2100 psi 2 gpm vertical shaft pump..the problem is that there is water leaking from every weep hole at the bottom of the pump when running. Oddly enough,the pump still puts out significant pressure but less than it should due to the leaking water. What is the most likely cause of this?..is it the high pressure water seal(s)? If so,how do I repair it?


... Pressure Washers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1022 seconds