Having problems with your Neff 24 in. S5443X2 Built-in Dishwasher ?

S5433 no life in the machine, have changed the fuse but still dead.


Answers :

Repair Help & Product Troubleshooting for Neff 24 in. S5443X2 Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

S5433 no life in the machine, have changed the fuse but still dead.


... Neff 24 in. S5443X2 Built-in Dishwasher

Dead dishwasher? I have an Prima LXP600 dishwasher that doesn't work - no power light, no beeps, no anything. I've changed the fuse and used different power sockets. Is there anything that I can investigate, or alternatively is it likely to worth calling an engineer? The machine looks almost unused (was in a repossessed house that I bought, so no history), so I'd like to think that it's got some life left in it!


Please find some help from the link below;\012\012\012http://www.repairclinic.com/Dishwasher-Repair-Help ... Dishwashers

When switched on the machine trips the power. Changed fuse in plug and tried different socket but still same problem? took bot of machine no visable burn or soot marks? any ideas


Is it tripping the breaker in the breaker box? If so you have a short to ground. Could be A bad spot on the dishwasher cord. Turn power off and pull dishwasher out and check the power cord all the way back to the dishwasher terminals ... Dishwashers

Hi, I have a Lamona HJA8362 dishwasher, which seems to have no power, as control panel is unlit with power button depressed (on). I changed the fuse, no different. The machine stopped midwash too, water still in bottom. Any ideas? Thanks, G


... Dishwashers

The dishwasher stop during the wash cycle. It did finish draining the water from the tub. The machine is not showing a power signs, I check the circuit breaker and the fuse is not tripped. I open and closed the door and the door latch seems to be working fine. There is just no power to the washer. Usually when a machine breaks down, there still is power or buttons that light up on the front of the machine. I looked on the internet and many say that the fuse could be tripped. No where can I find


... Whirlpool DU912 Dishwasher

I started working with the Karcher KB4040 pressure washer and all was well for 1-2mins, then it sputered a bit and all power died. All hoses were still attached properly, it hadn't blown a fuse in my house and the fuse in the plug of the washer is working fine.When I switch it on I get nothing. Do you think the motor has packed in? I borrowed the machine from my neighbour who's away on holiday, so don't know much about age of the machine. Any advice much appreciated.


If the water is in anyway impeded, like kink in hose the unit turns off and goes into protection mode. That it it shuts down for a pewriod of time depending on how hot it may have got.\015\012When its rested try it again ensuring you definitely ... Karcher 1750 psi Electric Pressure Washer

Have a Teka dishwasher DW6 55 Fl First three lights stuck on and machine will not allow you to change to any other programme. Machine still had water in base.


... Dishwashers

Washer went dead. replaced thermal fuse and it worked for about a week and went dead again. Before going dead it seemed to take it a long time to do a load of dishes. The last load ran 1 1/2 hours and still showed 45 minutes to go on the timer before it quit completely. Any ideas?


Sounds like you have a bad control board on unit.and the reason the thermal fuse went out is one of the relays are getting stuck on unit. before long the fuse will go bad again when the resistance level gets to high again. i would replace the control ... KitchenAid 24 in. KUDP01DL Built-in Dishwasher

E6 I have been getting E6 error message over and over again. I have had the machine to pieces, cleaned out the pump and hoses, and still the same problem. Occasionally, the error message changes to E8 or E1, but no matter what, I can't get it to work. Any ideas? When I start the machine, select any program and close the door after a short while the machine does not complete the wash cycle and I get the following message either: E1 or E2 will appear in the control panel Any suggestions Dave M


I had this problem and fixed it tonight. When selecting a program water pumps into the machine, but with no drain i ended up with too much water and error code E6.\015\012\015\012I traced the fault to a broken wire between the electronic ... Smeg DWI614 Built-in Dishwasher

We have a Bosch Model SKT5102GB/07 and the problem is as follows; we load the dirty washing and start the washing process, the machine then goes through the full cycle of wash. Once finished you open the door and notice that the washing is still dirty and a large pool of water is laying in the bottom of the machine. We have had an independent engineer look at the machine and he has advised that the pump needs changing. Look forward to your reply, thank you. Regards Michael Ballard.


Replacement parts are available here\015\012http://www.repairclinic.com/SmartSearch/SmartSearch.aspx\015\012\015\012on the narrow ... Bosch Dishwashers

No water coming into machine. Programme not running because the machine is still trying to fill. If I add water the machine does drain. Was cleaned with a good dishwasher cleaner only last week. Nothing to moved or changed yesterday before it stopped working properly.


Turns out that the dishwasher had a leak in the bottom. No water could be seen leaking out because Bosch machines have a cut-off valve that means if a tray in the bottom of the machine fills up with water, the float valve doesn't allow anymore water ... Dishwashers

Not working, changed fuse still not working. can i see diagram to check inside them


... General Electric Adora GHDA676NSS Stainless Steel Built-in Dishwasher

Zanussi dw927 not filling inlet valve changed,supply to machine ok, calls for water solinoid activates for about 30secs shuts off and machine does no more. cleaned out two blue plastic pipes situated under a plastic cover which were both blocked, and put a hose jet wash thru where they were situated to clean housing out, put blue channels back still not filling up and now the inlet solinoid wont switch off when when it should and programme advances heater now comes on with no water in.manually


... Dishwashers

Our Asko D1796 dishwasher has all lights flashing and is displaying a F2 message, which according to the good book means there is too much water in the machine. I have followed the instructions for a normal inlet time but the indicators will not change. Is it trying to tell me the Drain Pump is dead? A new drain pump was fitted three years ago. There is no eidence of water in the machine. Can anyone help? Thanks. Alan


Hi Alan,\015\012\015\012The F2 on Asko means it's sensed an overfill, that in itself though can be provoked by a couple of thing's. First, check for blockage at the end of the drain hose where it connect's to your household plumbing, be it under the ... Asko D1796FI Built-in Dishwasher

I have a Bosch dishwasher, M# SHU3035UC/U12. After the cycle is finished, the water is still on bottom of machine, it doesn't pump it out, so I changed the pump. Now when it washes, it fills and washes, when the timer advances it dies, there is no noise and nothing happens, the only way that I get the machine to pump water is by lifting the red overflow lever. Only then does it pump out the water. what can be my problem?


... Dishwashers

Maytag dishwasher has no power changed control panel and thermal fuse still no power...cb ok outlet ok power under dishwasher ok.....still no power


Hi\015\012\015\012Please post back with the manufacturers name and model no of your Dishwasher for further assistance.\015\012\015\012Daniel ... Dishwashers

Kenmore dishwasher... filled up with water and its lights went off.. no buttons work acts like no power. check the house fuse box - ok ... check the 2 door switch - ok .. checked the thermal fuse - ok ... so, i picked up a new board and changed it out. still wouldn't run.


Did you check power to the unit? Double check the common and grounds. When servicing I will disconect(unplug from wall) power to the unit. Is it pluged in? Use another outlet(the outlet under the sink may be wired thru a switch for a disposer)even ... Kenmore 24 in. 16032 Built-in Dishwasher

I have a Bosch dishwasher, M# SHU3035UC/U12. After the cycle is finished, the water is still on bottom of machine, it doesn't pump it out, so I changed the pump. Now when it washes, it fills and washes, when the timer advances it dies, there is no noise and nothing happens, the only way that I get the machine to pump water is by lifting the red overflow lever. Only then does it pump out the water. what can be my problem?


Hi There,\015\012\015\012Your description seems to indicate a fault in the water heating circuit or components. This is often the reason for a wash cycle not finishing and draining. As the machine will drain when you lift the overflow lev ... Dishwashers

Westinghouse SB915WJ is leaking cold water underneath machine. Working fine, just leaking water. Have changed door seal but it is still leaking. Also tried leveling it but this has not helped. Would like to access underneath and see if clamps are on tight but don't know how to access this part of machine.


... Westinghouse Dishwashers

Hello I just borrowed a k archer k 2.87 water blaster from a friend and forgot to turn water on before starting motor. Motor stopped after a few seconds and now won't start. Online guide says to change fuse but nz version doesnt have fuse in plug. Do i have to take machine apart?HELP Please!


Most of the time it is the GFCI on the end of the plug that goes bad. If it were me I would cut off the GFCI and wire in a standard 120v plug. If it still doesn't work after that then there is a good chance that something electric internally has gone ... Karcher PSI Electric Pressure Washer

Need a service/repair manual for a Bosch SGS0905AU/01. The machine is completely dead (no display) after a burnt smell came from it. On the pump motor is a broken/melted brown attachment with a broken ceramic(?) disc inside which looks like some type of capacitor. I really need to know what this is/was so I can replace it. Also, need to know whether there is another fuse somewhere in the machine as that has most likely blown as well. TIA


Hello,\015\012\015\012Welcome to FixYa.\015\012\015\012While I can provide a overall Bosch service manual if you post an email address, Based on your description I'd say the issue actually with the motor start relay and consiquently the control...as ... Bosch Dishwashers

My LG washing machine is dead. It is in my summer home and it worked before we left. The electric outlet is fine and the water supply ok. What could be wrong? Is there a fuse somewhere in the machine that can be checked? Model # WM2277HS Thank you fro your assistance


The control board is probably dead and there is no serviceable parts. There is a fuse in the board but it's encased in acrylic for moisture protection. You will have to order a replacement control board. Good luck. ... LG Dishwashers

There seems to be an electrical fault in my dishwasher. It is a slimline candy dishwasher purchased only three years ago. Everytime I try to start it all the electricity goes in the downstairs of my house. I changed the fuse twice and it worked for a while only for the same thing to happen again. I also tried to turn off all other electical equipment downstairs to see if this made a difference, but it still didn't work. Would you have any idea what is wrong with it? Thanks. S. Byrne


Hello sue by rne.. \015\012If your fuse blows when you are running the dishwasher alone, I would agree that your dishwasher may have a problem however becuse you stated that it works sometimes..I am more apt to believe that when you run the di ... Dishwashers

Hygena ahy-8122 the machine switches on starts wash cycle then trips rcd in home fuse box.trips somwhere between cycle 2 & 3 .have isolated & dissconected heating element but still trips rcd.any ideas?.thanx


... Dishwashers

I have a candy futura cdf322-80 dishwasher,done a load as normal then i put it on the next day and there was nothing no lights came on nothing, i checked the fuses and the socket they were fine,so i had an engineer out who said there was power going to the machine so he said it was the contol panel which is situated behind the temperature and programme buttons so i bought this part and replaced it but still there is nothing.


I would check for myself if there was power going to the machine. If it acts the ways your does, then either the control panel or the power supply is at fault. Slight possibility a wire that runs between the two may be faulty, but not as common ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1119 seconds