Having problems with your NIB Shop Force Universal Pressure Washer Accessoriesnib ?

When I turn on the shop force 1750 electric power washer I get water pressure in intermittent time frames. For example, it may run for a second then stop for ten seconds, then start again for three seconds then stop for 3 seconds then start for a half a second then stop for five seconds etc. until ?. This type of pattern continues for at least ten minutes, which is when I give up. I have tried adjusting the the water hose pressure, high, low. middle, nothing changes. This happen when I have the


Answers :

The usual cause of this is sticky Orings in the water admitance valve.
\015\012
\015\012Take the valve apart and clean the bore with crocus cloth wrapped around a rod and replace the Orings and lube with a bit of plumber's grease and reassemble.
\015\012
\015\012The admitance valve on most pressure washers shuts off the incoming water when up to pressure and admits more when you reduce the pressure by releasing the trigger. Sticking of this valve is the MOST common pressure washer problem.
OK here's what you do: Very patiently dissasemble the housing at least enought to gain access to the valve body caps on the pressure pump unit. Don't worry about the electric motor part just the pump itself. Be careful to note the location of each screw and part you remove. They may be different lengths and you want to be able to put the thing back together again exactly the way it came apart. I mean the housing or chassis parts, that is. Now once you gain access to the pump you should see valve body caps in four or six locations on one ore more sides of the pump. They will look like bolt heads, big ones. Pick one as a starting point and unscrew it. Remove it and the spring and valve components carefully noting the order of assembly. Set these parts aside and mark which hole you removed them from. Then continue on to the rest of the valves in the same way so that you can then inspect all the pieces and compare them againstthe other valves without losing track of which parts came from which hole. Clean all the parts and lube them up with Silicone spray. Shake the can really good before you use it. Thoroughly inspect the passages in the pump body for rust, debris, corrosion or really anything that should not be in there like pieces of torn o-rings or plastic shavings from the factory. Also look for metal shavings from the machining process that may not have been rinsed out of the pump body during manufacturing. Remember you said yourself it broke almost from the time you first used it. I can tell you that you just learned a valuable lesson. Sometimes things are not assembled properly at the factory or there has been some problem with the process that was overlooked. That means that things that are flawed will always tend to break very soon after being put into use the first time. This goes for anything mechanical even cars. So what that is telling you is that the problem should be simple and easy to correct because you are only looking for what they did wrong during assembly and you aren't concernined with looking for worn out parts. Make sure all the valve assemblies you removed are assembled in exactly the same order. If one is not the same as the rest, that's the problem. Make sure they are clean and free of grease, corrosion, debris. Spray silicone lube all over tem and all down inside the pump body and reassemble everything. It should work fine after that. OH wait! While you are at it, remove the tip from the wand and make sure there is no restriction in the tiny hole from something like a small rock getting stuck in it. That will wreak havoc on the pump and make it keep opening the pressure bypass because of over pressure. Kinda like when the pump is running but you are not spraying. The pump recirculates water to prevent over pressure. Anyway don't be afraid to blow out all passages with compressed air while you have the pump disassembled. Anyway like I said carefully reassemble everything and give it a try. hould work great. I think I'm going to go do mine, too now that I've put all this thought into it! Good luck.
Repair Help & Product Troubleshooting for NIB Shop Force Universal Pressure Washer Accessoriesnib

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

When I turn on the shop force 1750 electric power washer I get water pressure in intermittent time frames. For example, it may run for a second then stop for ten seconds, then start again for three seconds then stop for 3 seconds then start for a half a second then stop for five seconds etc. until ?. This type of pattern continues for at least ten minutes, which is when I give up. I have tried adjusting the the water hose pressure, high, low. middle, nothing changes. This happen when I have the


The usual cause of this is sticky Orings in the water admitance valve.\015\012\015\012Take the valve apart and clean the bore with crocus cloth wrapped around a rod and replace the Orings and lube with a bit of plumber's grease and reasse ... NIB Shop Force Universal Pressure Washer Accessoriesnib

The washer works for about 10 seconds the stops will start up again after about a minute then after ten seconds stops again. It's getting plenty of water (Hose not kinked) The reset is not kicking in. It stays on. ????


... McCulloch Electric Pressure Washer 1800psi 145 GPM Induction Motor Cart

A feew weeks ago Smeg STA6047 dishwasher stopped in the beginning of the programme after approx. ten minutes, and gave the error code E9. There had been clearly water in the machine, but maybe not enough and the detergent box was not open. However, when technician came by two weeks after, the dishwasher worked and he said it was in order. But only after being used only once, the same problem reappeared. First the washer gave the error code E8, on the second try E9. And now it does not start at a


As you know E9 is linked to the water inlet problem. \015\012\015\012There are two scenarios here - 1) Are you using the Aqua-Stop safety system? If this is trigerring then it can shut the inlet water. The reason it can trigger is if the ... Smeg Dishwashers

Got a Indesit Di620 Dishwasher that trips RCD after power up & immediateley as you shut door.Fault is definately related to pressure switch, disconnected pipe to switch and then able to start cycle, without tripping, small amount of water out of pipe,but cycle only lasts for a few minutes, then stops. ( blowing into pressure switch trips rcd )How can i test switch, or is it a water level problem ??Any help would be good, thanks S.C


... Dishwashers

I have whirlpool Dish washer model GU 120 ES (bought in 2001). When we start the dish washer cycle the unit starts for a minute, then the "start indicator" light flashes. As indicated in the instructions, we press the "start button" for five (5) seconds, at this time the washer clears the water out and stops. If you can assist this would be greatly appreciated. Thanks Jeff


I called the service tech.... ... Whirlpool Dishwashers

I have a Husky 2600 2.3 pressure washer with a Honda motor that is only two years old. When I connect the hose and the sprayer I can shoot water through the sprayer no problem. The second I pull start the engine the water stops. Why would water only come through when the engine isn't running?


... Honda Pressure Washers

My Bosch Dishwasher does not drain all the water out of the dish washer after the finishing cycle...I usually start the washer and then push the drain cycle and it starts to pump for about 10 seconds and stops and starts and pumps again for 10 seconds and stops and then pumps for about 25 seconds and stops....doing this manual drain twice empties the dishwasher of the excess water....what may the problem be?


... Bosch 24 in. SHE43C05UC Stainless Steel Free-Standing Dishwasher

Hello, I have a CONSTRUCTA S9W1C dishwasher with aquastop. Unfortunately, I tried once to start it with the house water supply closed. Of course it stopped after a few seconds. After that time, when I start it, the water pumps works and after some seconds the cycle stops. It gets no water. I've checked and noticed that no water passes through the aquastop valve. The aqua stop has two wires that get into the dishwasher. Do you have any suggestions? Thank you for your time Alex


... Dishwashers

My Troybilt pressure Washer Model 020207. runs forabout 30 seconds then the motor stops. Acts like motor is locked up. Motor can't be pulled until water hose is disconnected. Took the water pump off and the 6.75 Briggs starts and runs like new. What could be the problem.


It sound like a digafame problem/or/carborater bowl has some water or needel valae is sticking cheack them if not the problem then you may have a crank shaft problem good luck see if there is oil in motor ... Briggs & Stratton Pressure Washers

Miele Optima G 2430 - The dishwasher will pump water in for 5 seconds with the Intake/Drain light flashing 5 times. Then the light stays on for 5 seconds and it does nothing. This process is repeated for about 10 minutes untill the washer is filled to the just below the door with water. Then the washer starts running for about 1 1/2 minutes and drains the water. Then it all starts over. If I let it do this for a hour - The display reads F12 with the Intake/Drain light flashing.


Hi\015\012\015\012The first thing that should be checked is if its draining\015\012properly as it could be that the drain hose is clogged and needs to be cleaned.\015\012The drain pump also should not be clogged. ... Miele 23 in. Novotronic G841 Built-In Dishwasher

Hotpoint df32 my df32 stops working during its water intake The water intakes come in 3 10 to 20 second pumpings.Its always after the second .spurt that it stops. In order to start it working again,sometimes a quick on/off of the main jkitchen water tap will start it, otherwise I have to advance the timer manually


REPLACE WATER INLET SOLENOID ON WASHER ... Hotpoint 24 in. DWF32P Free-standing Dishwasher

My built in Whirlpool adg 9340 washer won't start a cycle at all. It seems to start a cycle and after 1 minute it stops and it starts beeping. Also water remains on the bottom. As soon as the cycle starts it drains that water and brings new water in which stays there. It won't work for more than 1 minute....


... Dishwashers

GE PDW7300 dishwasher - must slam the door shut to get a light on the panel and when the START button is pressed, it looks like the dishwasher is cycling thru a wash, but there is no water. When I press the START cycle again, it seems like it thinks its pumping the water out for a few minutes, then the light will go off. If I start it again and push really hard against the door, I can hear the water go on. But if I stop pushing the door, the water stops. The dishwasher was installed in 2001, but


... GE 24 in. Profile PDW7300G Built-in Dishwasher

I have a Briggs & Stratton gas power washer. This is the 1st time this year that I have used it. I put in fresh gas, hooked up the water supply. The engine started and then quickly stopped. I had to release the water pressure in the hose before I could pull start the engine. The only way to keep the engine running is to hold down the spray nozzle trigger. Once that is released the pressure in the hose builds up and the engine stops.


Sounds like the unloader is not working correctly. Try replacing it and see what happens. ... Briggs & Stratton Prosumer 20324 Gas Pressure Washer

My Dishlex global 300's rinse light is flashing after 5 mins use. About 2 inches of water stays at the bottom of the washer. Bought this second hand and it has not been used for a few months. Do I need to fill the reservoir under the washer or lean it at 45 degrees to dislodge anything in the sump. If you have had the problem of the washer starting its program and then stopping after 5 minutes and the rinse light flashing I would appreciate your advice. Cheers Hyph


The flashing rinse light is an error code. I am assuming that your control board is good because the lights are working. I'm also assuming that this model has two pumps. One for filling and one for draining. The rinse light flashing is probably i ... Dishwashers

My hotpoint dishwasher keeps going off it starts the cycle and you can hear water coming through but after about a minute or two it stops and the second and fourth lights flash all the time does anyone know why?


I am assuming you have tried the possibility it is the water inlet circuit which could be faulty.\015\012\015\012Check page 13 of the ... Hotpoint 23 in. BFI62 Built-in Dishwasher

Diagnostic dishwasher stops shortly after starting a cycle. I start a cycle, it runs water into unit, starts to wash. After 5 seconds it stops, 10 seconds later it starts again, repeats 2 more times, then all lights on panel go out. any help would be greatly appreciated.


... Samsung 24 in. DB5710DT Stainless Steel Built-in Dishwasher

I need a diagram and fixing help for a miele G892 SCU plus. The dishwasher starts up with the intake draining light blinking and the saltpc light on. Then the start stop button turn green on. It sounds like it is filling with water but a few seconds it stops and turns off. I open and no water is filling. I believe it is the water pump, what do you think? How do I install it?


... Dishwashers

Hello , we have a blanco BFDWC65 dishwasher supplied to us by our builder , The dishwaser fills with water ok then once in cycle it starts (with all operating lights ) then stops , it continues to start then stop for the rest of the cycle , Quiet some time later it finished and then drained the water ok , now it struggles to get to the end of the cycle. have checked all filters , water pressure and for clogged hoses , everything is ok in that department. Any help would be apprieciated


I would suspect the control board in this type of behaviour. As the machine is new I advise no interference, but to open a claim under warranty. You would have all the warranty papers for this unit, or should have received them from your builder. The ... Dishwashers

Have a Miele G1220SC dishwasher. It recently developed a strange problem: when switching it on ALL program lights come on and the machine starts taking water. after a while it stops taking water and starts to pump water, all the time all program indicators remain on. if you leave it on a while ( about 4 or 5 minutes) it is impossible to switch off the machine with the main switch, all you can do to stop it is unplug it. anyone experienced something like this and have any idea what part is malfun


Follow this steps and fix it. God bless you\012 \012 Heating Element\012 \012 \012 \012 \012 \012 \012 \012 \012 ... Miele Dishwashers

I have a honda 2600 pressure washer. After running fine for a couple of seconds the water will stop flowing out the tip. It is receiving water,but will not flow it to the pressure hose. I even disconnected the pressure hose and no wate was flowing out. When I shut the pressure washer off it would then flow water to the hose again. Please help


This is a symptom caused by a sticking Unloader valve. The Unloader valve is inside the pump outlet body under the large black knob. \015\012Example picture : ... Honda Black Max 2600 PSI Pressure Washer

I have a Siemens Dishwasher. I'm not sure of the model but it is built in, has concealed controls and was purchased about 6 years ago at Best Buy. It sort of looks like the SL85. When started, it runs for a few minutes and then starts to make a horrible sound. ALmost a grinding sound but may also be like water trying to get through a small opening. The sound does not stop even after turning off the DW and even the power to it. Only turning off the water supply does it stop. Help?


... Siemens SL85A705UC 24 in. Built-in Dishwasher

My maytag quiet series fills with water and then starts for 5 seconds then stops. This happens 4 times and then the entire system just stops. To help troubleshoot I used a screw driver to trigger the closed door so that I could leave the door open when the cycle starts and the pumps seems to be working and water sprays all over the place. I also took apart the impellar blade to make sure there was nothing jammed and everything is clean. Maytag MDB7500AWW


... Maytag 24 in. MDB7600A Jetclean® II Built-in Dishwasher

DISHWASHER STOPPING I HAVE A WHIRLPOOL ADG 7560/01 DISHWASHER. AFTER 4-5 MINUTES IT STOPS AND HAS A CONTINUOUS BEEPING AND THE START LIGHT FLASHES 4 TIMES THEN A PAUSE etc. I HAVE CLEANED THE FILTER LIFTED THE MESH AND CLEANED THE BOWL OF ANY DEBRIS AND WATER. I HAVE ISOLATED IT FROM THE ELECTRIC SOURCE LEFT IT FOR 10 MINUTES AND STARTED IT AGAIN TO FIND IT DOES THE SAME . LOST IS THE WORD THAT SPRING TO MIND. HELP!! MARTIN


... Dishwashers

Motor starts, stops, starts, stops etc never running completely. not putting out much water pressure. not building pressure??


Is you nozzle plugged? That is what this sounds like. ... Karcher PSI Electric Pressure Washer
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1439 seconds