Having problems with your NIB Shop Force Universal Pressure Washer Accessoriesnib ?

It runs but has no pressure - NIB Shop Force Universal Pressure Washer Accessoriesnib


Answers :

Repair Help & Product Troubleshooting for NIB Shop Force Universal Pressure Washer Accessoriesnib

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

It runs but has no pressure - NIB Shop Force Universal Pressure Washer Accessoriesnib


... NIB Shop Force Universal Pressure Washer Accessoriesnib

When I turn on the shop force 1750 electric power washer I get water pressure in intermittent time frames. For example, it may run for a second then stop for ten seconds, then start again for three seconds then stop for 3 seconds then start for a half a second then stop for five seconds etc. until ?. This type of pattern continues for at least ten minutes, which is when I give up. I have tried adjusting the the water hose pressure, high, low. middle, nothing changes. This happen when I have the


The usual cause of this is sticky Orings in the water admitance valve.\015\012\015\012Take the valve apart and clean the bore with crocus cloth wrapped around a rod and replace the Orings and lube with a bit of plumber's grease and reasse ... NIB Shop Force Universal Pressure Washer Accessoriesnib

Champion dishwasher we have a champion freestanding dishwasher at my church. after the cycle is completed, the pressure guage behind the washer still shows 25-30 and it contnues to spray water. not forced by the motor, but more like a stuck open fill valve. if i turn off the water and run it, then turn the water back on, the valve is closed and does not let water freely in. butif i run it with the water on, it will continue to spray in freely after the cycle light goes out and you open the door.


If you turn the unit off from the circuit breaker will the water still run?if so the guts inside the solenoid valve are worn.you can call champion and get a kit to replace the worn parts and its not difficult to do.hope this helps. ... Dishwashers

How to get pressure washer to spray shop force 1300 psi pump working


... NIB Shop Force Universal Pressure Washer Accessoriesnib

The last time I used the pressure washer was running fine. A few minutes later I tried to start it up and could barely turn it over. I removed the recoil and could turn it a little easier backwards. The motor is a Honda GC190 on a karcher pressure washer and has 20 -30 hours of running time. Thanks Clint


... Karcher 2500 PSI Pressure Washer

Water runs out of the pressure washer. it still has water come through the nozel but no pressure. water runs out of the washer itself


... Karcher K2.26 Electric Power Washer

I left my craftsman pressure washer (the big one) running while i went for detergent. The pressure hose blew off and now the threads are stripped. can u help me?


You have more problems then just a stiped thread. the machine shouldnt be producing that sort of pressure if you dont have the trigger pulled.sounds to me like the pressure switch is faulty ... Pressure Washers

Briggs and Stratton Troy Bilt gas pressure washer one year old. I can get water thru pressure washer and bleed the air, water comes out the hose just fine until I start the pump. Then, I lose all water flow. Pump runs fine but when it's running, no water goes through.


... Briggs & Stratton Prosumer 20324 Gas Pressure Washer

I have a Generac pressure washer, model #01450-0, with a Honda 5hp motor. The motor runs fine, but the pressure hose pulsates as if the pump is intermittently making pressure, and the pressure out of the sprayer is about half of what it should be. A friend suggested replacing the seals in the unloader. I bought an unloader kit, replaced everything and it still runs the same. It will build a small amount of pressure, spray for a few seconds, then the pressure dropps to almost nothing. Any help ap


Take a small diameter wire and poke thru the discharge hole of the spray head to clean out.\015\012Second time in 6 months that I had the same problem. The problem is alway in the spray head. ... Pressure Washers

I have a 5HP Honda engine installed on a Excell pressure washer. While the engine readily starts, it will not continue to run unless I keep the choke setting nearly completely closed. When I activate the pressure gun, it seems to generate adequate pressure, however, when the trigger is released, the engine continues to run at the same rpm instead of the normal variable rpm that most engines operate at during idling periods. The engine will always cease running when I push the choke rod all the w


... Honda Pressure Washers

Home Depot has a lawn mower with the Honda GCV160 Electric start version engine. They also have a pressure washer with the Honda GCV160 engine. I have a disability that makes it difficult to pull the starter rope. I would like to get the electric start on the pressure washer. My local Honda bike shop service center said they use different blocks. Can I get a pressure washer pump mounted to the Honda GCV160 Electric start version engine? If necessary, are there adapter plates that can be purchase


... Karcher 2500 PSI Pressure Washer

I have an older Landa Pressure Washer. The burner is not working. Once I get the machine running and water flowing to the pressure washer, with the wand pressed, I flip the burner on switch....and nothing...I have no idea how to work on a pressure washer burner. I have been told it could be the igniter, but I don't know how to fix it if it is. Any help is appreciated.


Check for 12V at the igniter connector with the unit running. If you have 12V and no igniter it may be stuck or bad. Thrun the unit off and read continuity across the DISCONNECTED igniter plug / terminals to the igniter. No resistance = open ignit ... Pressure Washers

I have a honda 2600 pressure washer. After running fine for a couple of seconds the water will stop flowing out the tip. It is receiving water,but will not flow it to the pressure hose. I even disconnected the pressure hose and no wate was flowing out. When I shut the pressure washer off it would then flow water to the hose again. Please help


This is a symptom caused by a sticking Unloader valve. The Unloader valve is inside the pump outlet body under the large black knob. \015\012Example picture : ... Honda Black Max 2600 PSI Pressure Washer

I have 2400psi washer gas will run w/hi pressure, when i release trigger and then pull trigger for hi pressure it will take minutes to get hi pressure, longer i run longer for pressure to come back.


Hi and welcome to FixYa. I am Kelly. \015\012\015\012First off check to see if there is an inlet screen at the house water hose connection point. Remove it and clean it then reinstall. If the screen was clean.......\015\012The u ... Honda Karcher G2400HH-R Pressure Washer

2-yr old troy-bilt pressure washer with honda gcv160 engine. seems to run well, but when trigger is pulled get full pressure for less than 5 seconds before reducing to house water pressure. when left running, looks a black plastic pressure relief valve starts blasting hot water. appreciate whatever insight you can give. Thx


It sounds like an air lock. Try this: With the machine off, connect the hose to the washer and let it run for several minutes to get all of the air out of the hose, and to purge any air out of the pump. Shut off the water, and connect the high pre ... Briggs & Stratton Pressure Washers

I have a Northstar pressure washer powered by a honda GC160 engine. The last time i used it, water leaks from the bottom of the unit, whether it is running or not. When running, the pressure is fine. I have felt underneath and it appears that the water is coming from the second opening from the rear. Is there a pressure relief valve there. I have a manual but cannot find any descriptors for underneath the motor.


This is a piston seal issue. You can get a kit to rebuild the pump. ... Comet AXD 3020 G Pressure Washer Pump

020272 pressure washer will not spray high pressure water running or not running same amount of pressure comes out


... Karcher 1550PSI Pressure Washer

Hi there, Ok, i think i'm getting close to solving this problem. I have an LG dishwasher- Model # LDS 5811ST. I have stripped it down and clean all hoses etc. It is running fine through all the cycles. The only problem is that it has no water pressure. In other words water is pumping into the dishwasher but it's like there is no pressure behind it to force it through the holes in the propellers so it's just kind of dumping water out as opposed to having any forced pressure. Hope this makes se


Water will flow out of your inlet pressure. The pump takes from your machine to spray. The same water is circulated during wash!Hence try the method I have informed you. If it is a micro controller problem you have to contact the service ... Dishwashers

Hi there, Ok, i think i'm getting close to solving this problem. I have an LG dishwasher- Model # LDS 5811ST. I have stripped it down and clean all hoses etc. It is running fine through all the cycles. The only problem is that it has no water pressure. In other words water is pumping into the dishwasher but it's like there is no pressure behind it to force it through the holes in the propellers so it's just kind of dumping water out as opposed to having any forced pressure. Hope this makes se


Try adding some more water to the machine after it has done the fill cycle do not over fill it. if there is no change in the performance the you need to replace the main wash motor.\015\012if there is achange the you need to change the fill val ... Dishwashers

My pressure washer won't build up any pressure. it will run water when you pull the trigger, but it is the same pressure as if the unit if not running


I'll assume you have an electric rather than a gas powered unit. First check the button on the plug to be sure the GFCI hasn't popped and be sure the outlet has power. With the water faucet turned fully on and the power switch on squeeze and ho ... Pressure Washers

I'm trying to get a Durabuilt pressure washer (model DB1303) to work. After hooking up the water hoses I plug it in and turn on the power. It sounds like it's running but there is no increase in pressure and it runs continuously. I only let it run for about 10 seconds and then turned it off. I tried it a couple of times...no luck.


... Coleman Powermate DuraBuilt 1400 PSI Pressure Washer

Hi I have a Troy-Bilt Pressure washer 2200 psi model 20292. I've used it only 4 or 5 times. It ran great for an hour today then it lost pressure. Seems like the pump is not working. The engine runs fine but no pressure. The water runs through the nozzel and I blew air in the lines to make sure there is no blockage and found no blockage even in the pump lines. Any ideas. Tom


... Briggs & Stratton Gas Pressure Washer 20244

Excell vr2500 pressure washer ,no pressure, took off high pressure hose at bottom of washer , get water flow, but flow does not change when engine is running full throttle


Check the water filter ---high pressurehose must have bbackpressure to develop pressure so disconecting it wont acheive ,much ,if you have agood water supply ,oil in the pump--- adjust pressure by srewing the brass fitting that the pressure hose atta ... Pressure Washers

Pressure washer exh2425 by devap, engine runs but i have no pressure just water from hydrant


It could be the valve(s) ... Devilbliss DeVILBISS Devap DVH2600 Gas-Powered Pressure Washer

Pressure washer runs fine but no pressure out of nozzle, model # 580.752521


... Pressure Washers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0879 seconds