Having problems with your Northstar Pressure Washer 2800 PSI ?

Can i have a pump oil leak because of an over fill of pump oil?

\015 Pump oil is leaking when i have the pressure washer on\015

Answers :

Repair Help & Product Troubleshooting for Northstar Pressure Washer 2800 PSI

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Can i have a pump oil leak because of an over fill of pump oil?


... Northstar Pressure Washer 2800 PSI

I borrowed my nieghbors power washer. It worked the first day all day. In the morning i filled the gas with a fuel stabiler, and 30 oil. I may have over filled it. Upon turning it on the oil started leaking from the air filetr compartment. It starts, but then smokes starts to fume and all the oil leaks. Did I break it or is it a easy fix. I cleaned the filter housing. Also the filter was soaked with oil. should i get a new filter and install it or what is the solution. need help.


You will need to get a new filter, and drain some of the oil out of the machine. If you over fill these this will happen. 90% of the time nothing is broken. ... Karcher 2500 PSI Pressure Washer

I bought a HILMORE PUMP 309515003 for my pressure washer. My old pump had an oil fill port on top and this pump doesn't. Does this pump use oil if so where do I fill it? Thanks


... Karcher Pressure Washers

No water pressure coming out while ingine is running. hoses/ attachments not clog. Pulled and opened pump, didn't see anything broken although noticed pump was filled with oil/lubricant but about 1/4" below top surface. Is it suppose to be filled to the top? What kind of oil is used on the pump? And how come there's no water pressure coming out while the motor is running and handle trigger engaged?


If you can find the model # then you can call tech support for free advise.\0121-888-279-9274 ... Karcher Pressure Washers

Pumpoil started to leak out after a few hrs of use. i have pump oil that i originally got over 12 yrs ago with the pump---is that unopened can still good? and how do you add and how much pump oil do you add? thanks----gary


12years doesn`t have the effect on oil that it does on women,so you should be right.has the machime ever done this before?is the oil white?i think you should drain the oil completely there will be an indicater the some where to tell you how mch,I don ... Pressure Washers

Tub leaks, with a partially filled tub (2.5 inches measured from the lowest point over the pump assembly.) Promblem occured after the washer was idle for 3 weeks. Have just replaced the main water inlet valve. The fill tube is not the source of the leak, the top arm feed is fine also.


I am assuming leaking when it is running, not sitting idle. Leaking from the door? Fill and run unit for 1 minute with no detergent. Open door. Are suds present? Suds turn into water when they drop to the floor. Suds can flow over the lip of the tub ... Maytag MDB7100AWB Dishwasher

Oil leak appears to be from pump, not engine, GC160. What oil and how much should be replaced. what might be source of leak


Some pumps have a side glass and oil should be half of side glass and depends on manufacture oil is different if general pump you can use 30w non detergent ... Honda Pressure Washer PSI 3000

Changing pump oil on ryobi pressure washer model ry80030 guy oil leaking out of breather on pump do I also need to change seals and if so how do I do this


... Karcher 2500 PSI Pressure Washer

Oil leaking from pump


Top is a breather you may be overfull of oil most pumps you can use engine oil .drain and put in half litre or if it has a sight glass top up to low side of glass and try it out.possible your seals on way out this usually then leaks at front or gets ... Pressure Washers

Oil leak at top of pump


The oil in the pump is probably leaking because a seal is blown and water is getting into the piston housing. Take a look inside at the oil. It should be brown and translucent. If it is gray, white or milky, you have a blown oil seal. This reserv ... Northstar Pressure Washers

2700 Series Presser Washer, and I need to change the "engine" oil. There on two oil "yellow" fill point, and the manual talks about changing the pump oil. How exactly do I change the engine oil?


Look for a drain plug on the base of the engine.Take the fill cap off also, and it'll drain easier. ... Briggs & Stratton Prosumer 20324 Gas Pressure Washer

Had the Northstar 3000 psi Pressure Washer for 2 months and it started leaking oil from the pump during use. Took it to Northern and they are replacing the pump under warranty but said it was likely because I was using quick connects on my garden hose coupling and that was restricting the water flow making the pump overheat. They said never to use quick connects on the garden hose unless the opening is at least 5/8". Does anyone make such a quick connect? I hate having to screw the garden hose o


It is easy to check if your hose and quick connects are supplying enough water to the pump. Your pressure washer gallon per minuite requirements are printed on the machine and also on the pressure tips in GPM. Your post indicates 2.5 gpm but check yo ... Northstar Pressure Washer 3000 PSI

Asko Dishwasher starts the cycle by pumping out as it should. But does not stop pumping nor advances. If I click it forward manually it starts to fill and then before overfilling goes into pump out without washing then just repeats this. Pressure switch tubes and air trap chambers are clean and no leak to trip spill switch. I'm guessing It is either the timer or faulty pressure switch any clues ???


If has "mother board" then water could have got in.\015\012\015\012Here Asko is low cost make so check cost before serviceman calls & charges & charges and so on. ... Asko D1706 Built-in Dishwasher

Honda Black max 2700psi pressure washer leaking pump oil.


... Honda Black Max 2600 PSI Pressure Washer

I have a pump oil leak where is it coming from


... Northstar Pressure Washer 2800 PSI

I had a bolt break off the engine shaft end and tookthe pump apart and replaced the bolt. How do you fill the pump back up with oil?


The pump housing usually has a plastic viewport about half way up on side of pumpOil should come to middle of viewportUse 20 or 30 weigh ... Karcher 2500 PSI Pressure Washer

Pump oil seeps out of its fill cap. - Comet GXD2527G Pressure Washer Pump


More than likely you have water leaking into your oil, making the oil float on the top and out of the vent. Eventually you'll only have water, and no oil. Drain oil and replace. You will probably have to replace the seals between pump an ... Comet GXD2527G Pressure Washer Pump

Vulcan Dishlex Executive 14-10 Dishwasher leaking onto floor from right hand side when it was filling at start of cycle. Husband has checked the following: both pumps (main and waste) hoses, solenoid switch (inlet). Where can we find the float/level valve? Could this be the problem? What else to check? This is the second time it's happened - I don't use it that much. The previous time my husband replaced the inlet and outlet hoses. What is the proper level for water fill - never above the


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. If you have water leaks around the base of your dishwasher,\015\012you may be using a detergent that is ... Dishwashers

Hello, my Bosch Classixx dishwasher SGS43E42EU/21 has me stumped. It starts by taking in water but when "filled" pumps out for a couple of seconds then refills for say 10 seconds more before another 2 or 3 seconds of pumping out. This cycle continues for ages without starting to wash. I've tried various things: - checked the Auto Stop valve isn't being activated by leakage (removing the polystyrene float and bottom tray makes no difference - there's no leak) - the valve seems to operate it


Hello Dave,\015\012\015\012Sounds like an overfill problem - the symptoms are consistent with a failed pressure switch. Water enters the dishwasher through a chamber which has a float arm connected to a small microswitch -this is the pres ... Bosch Dishwashers

It starts running then stops - starts pumping in water then stops, etc. burning plastic smell near top... doesn't leak, gets power, but begins to fill, then stops - might start to drain (pump), but then that stops too...


... Frigidaire 24 in. PLD2850 Built-in Dishwasher

Pump oil leak where pump connects to engine


With that few hours, you need to return it as the seal shouldn't leak. Probably was improper pump assembly, so you should take it back, because it will only get worse and fail. Hope this helps you, Rick ... Northstar Pressure Washer 3000 PSI

Troy Bilt pressure washer model 020209 will not build pressure-have checked all screens and intake in pressure hose and garden hose from house to pump. water leaks at gun handle- took it apart and oiled piston- was ''grabby'' but now snappy but still leaks. Engine starts fine and runs fine. Please help.


A leaking gun will kill all the pressure. You may need to repair or replace the gun ... Briggs & Stratton Pressure Washers

SHX46B I have a 4 year old Dishwasher that filled up with clean water on it's own and leaked on the floor. There appears to ba a float switch switch on the very bottom of the unit that runs the pump if this happens. It won't stop until I remove the water caught in the plastic base on the very bottom of the unit. Drain is clear and this machine has worked fine until now. I'm thinking it may be a bad or leaky fill valve but how can I check?


... Bosch 24 in. SHU66C02 / SHU66C06 Built-in Dishwasher

E1 fault code Dishwasher runs for about 5 minutes. Water fills up at bottom of unit and then machine seems to pause then fault code E1 appears then water is pumped out from bottom of machine. There are no leaking pipes and drain is installed correctly. I installed a new wash pump and fault still appears.


Hi,\015\012I think both the heater and thermostat / trip switches need to be checked.\015\012If water is going in and out ok, then it seems to be waiting to heat the water. It sees a fault - so just clears out.\015\012Heating elemen ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1046 seconds